Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Building an HF shack around a 100 W rig: what to sort first, grounding and bonding or filters and gear?

ci_cover.jpg

Whether the rig is an IC-7300, IC-7610, FTDX10, TS-590SG, TS-890S, K3S or a smaller radio like an FT-991A or G90, the radio is usually the easy part of a new shack. Most of the trouble comes from how it connects to everything else: the power supply, the antenna system, the computer, the amplifier and the building's electrical system.

I'd like to compare how people order the work. This is my suggested sequence, and I'd like to hear where you'd change it.

First, safety bonding and lightning protection. Treat these as separate from RF performance. The mains safety ground, the equipment chassis bonds and the coax entry point need to work together. A common approach is a single entry panel or ground bus where coax shields are bonded and arrestors are mounted. Its ground rod is then bonded to the building's electrical service ground, so there is no separate "clean" ground at a different potential. Exact requirements depend on your local electrical code, so a qualified electrician is worth consulting.

Second, common-mode current. Many cases of RF in the shack, such as a distorted mic, a USB device dropping out or a hot microphone case, come from current on the outside of the coax shield and not from a missing ground. A choke at the feedpoint, and sometimes another near the shack entry, often helps more than another ground wire. A long ground wire can also be an unhelpful resonant stub at certain frequencies.

Third, power. A 100 W transceiver typically draws somewhere around 20 A on transmit, so a supply rated at 25 A or more is a reasonable starting point. Keep the DC leads short, use adequate wire gauge, fuse the positive lead and check voltage at the radio under load, not just at the supply. Switching supplies can add noise on some bands, so it's worth testing yours on the receive side.

Fourth, filtering and the amplifier. A band-pass filter helps mainly where a nearby transmitter or a strong signal on an adjacent band is overloading the front end, as in multi-operator or multi-radio setups. Otherwise it adds insertion loss and one more thing to keep matched. An amplifier needs a good 50 Ω load. A tuner can make the radio or amp see 50 Ω, but it doesn't remove loss in the feedline from a high SWR at the antenna.

Which of these would you do first, and do you think a 5 W or 20 W radio such as a KX3 or G90 changes the order?

  • Replies 2
  • Views 18
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

I'd put common-mode control ahead of almost everything except safety. Adding more ground rods or a heavier ground strap is a common reflex, but a lot of shack RF problems are really about where the antenna current returns. If the feedline is part of the antenna, the shield carries RF back into the shack. A choke near the feedpoint (a stack of suitable ferrite cores, or coax wound in a coil) is cheap and often changes how the whole station behaves.

One caution on the tuner point: the internal ATU in a rig such as the IC-7300 or G90 matches the radio to the line. It doesn't fix the antenna. On a non-resonant wire fed with coax, the tuner can make the transmitter happy while the coax runs at a high SWR and loses power as heat. If that's the situation, a tuner at the feedpoint or a different feed system may serve you better than a bigger amp.

  • Administrators

On filters, I'd test before buying. Modern rigs differ a lot in front-end design: some are direct-sampling, some use a roofing-filter superhet architecture, and some are hybrids. Local interference may come from a neighbor's transmitter or from a nearby switching supply, so a band-pass filter is not always the right answer. Check attenuator and preamp settings first, and use a dummy load and a short test antenna to see whether the noise comes from the shack itself.

If you do add band-pass filters, check their power rating and what they do to the SWR the radio sees outside the passband. Watch the amplifier handshake too. Band data or a keying line that isn't wired correctly can send an amp to the wrong band and cause damage, so confirm the interface before applying full power.

For layout, I'd keep the power cables, coax and USB/audio cables separated where possible, and cross them at right angles if they must meet. A ground bus behind the desk with short bonds to each chassis tidies up a shack, but it mainly serves safety and fault current. RF behavior depends mostly on what the antenna and feedline are doing.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.