Run or hunt? Deciding when to leave your run frequency for multipliers, SO2R and band changes
- Replies 2
- Views 15
- Created
- Last Reply
Top Posters In This Topic
-
Mod_Dan 1 post
-
Mod_Chrissy 1 post
A better way to browse. Learn more.
A full-screen app on your home screen with push notifications, badges and more.
I'd like to compare notes on one decision that shapes most contest results: when to keep running and when to go search and pounce (S&P). Most operators know the broad rule that running builds rate and S&P builds multipliers. The hard part is deciding when the trade-off has flipped.
A simple way to frame it is marginal value. If you are running at 120 Q/hr and each new multiplier is worth a lot of points, a 5-minute trip to grab a few mults may pay off. If the run rate has dropped to 40 Q/hr and the band is thinning out, S&P or a band change is probably better than calling CQ into silence. The N1MM rate window (last 10 and last 100 QSOs, plus hourly) is a more honest guide than how busy the band feels.
Some questions to get things started:
1. What is your rule for leaving a good run frequency? Some people use a fixed rate threshold. Others look at how many unworked multipliers are visible in the bandmap. A common rule is to leave the run only when the multiplier window shows enough needed stations to justify the lost CQ time, and to go back to the same frequency immediately afterward.
2. How do you handle band changes? A band change costs rate for a few minutes while you retune, check the new band and find a clear frequency. Changing on a fixed clock schedule rarely works as well as changing when the rate and the propagation say so. In multi-band contests, multiplier passing helps: after working a mult on a band you won't return to, move on. Pre-contest propagation checks (a quick look at predicted openings, plus a read of the skimmer on each band) help avoid blind switching.
3. Skimmer and spots: how do you use them? A local skimmer decoding your own receiver is a very different thing from cluster or RBN spots. In many contests, using spots from outside sources moves you into an Assisted category, while a skimmer fed only from your own station may still count as unassisted. The rules differ by contest, so read the specific rules before the event and choose your category deliberately. Whatever the category, spot quality matters. Busted calls and busy-band spots on the wrong frequency can waste more time than they save, so many logging setups verify a call before you trust it.
4. SO2R: is it worth the complexity? Single-operator two-radio setups work best when the second radio does something productive during the gaps in your CQ cycle: listening for multipliers on another band, or running a second CQ frequency. The basics are two radios, a switching box, stereo headphones, and a way to prevent both radios transmitting at once. On the RF side, band-pass filters and stub filters matter, especially if both radios may end up on nearby bands or share antennas. Without them, receiver desense can cancel the rate gain. Even simple SO2R, where radio 2 only searches while radio 1 calls CQ, can beat a single-radio approach if the operator can focus on both without fumbling.
5. Antennas and time on the band: The best operating strategy still depends on the station. Stacked Yagis or switchable heights let you pick the take-off angle that works for the path at different times. For the low bands, receive antennas can matter as much as the transmit antenna, because you work only what you can hear. A decent antenna for each band, plus the ability to switch quickly, is worth more than one great antenna on a single band.
6. Endurance: In a 48-hour event, fatigue costs points through busted callsigns, slow reactions and missed openings. Plan off-times in advance, ideally during the low-rate hours of the band you rely on. Some contests limit total operating time, so check the rules. Eat and drink on a schedule, not only when you feel like it.
How do you decide when to leave the run, and what do you track beyond the rate meter?
Link to comment
https://www.hamradiobase.com/forums/topic/11664-run-or-hunt-deciding-when-to-leave-your-run-frequency-for-multipliers-so2r-and-band-changes/Share on other sites