Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Dual-band mobile setup: FTM-500D vs ID-5100A vs TM-D710G, plus wiring, noise and cross-band questions

ci_cover.jpg

I'm planning a dual-band mobile install for 2 meter and 70 centimeter and want to get the basics right before I drill anything. The three radios I keep comparing are the Yaesu FTM-500D, the Icom ID-5100A and the Kenwood TM-D710G. I'm not trying to start a brand war. I'd like to know how people choose between them for daily mobile use rather than from a spec sheet.

From the feature lists, the FTM-500D is the C4FM/System Fusion option, the ID-5100A is the D-STAR option with a touchscreen, and the TM-D710G is the APRS-oriented one with a built-in TNC and GPS. Local activity is probably the deciding factor, but I'd like to hear what else matters. Control head size, button layout for blind operation and speaker quality all seem to count when you're driving.

Then there are the installation questions. Where should the main body go, and what's the safest way to run power? Direct to the battery with an inline fuse is the usual advice, but I'd like to hear about fuse placement, wire gauge and grounding. I'm also wondering how people avoid alternator whine and ignition noise, and whether cross-band repeat is worth planning around. Last, what mobile etiquette do you consider non-negotiable on busy repeaters?

  • Replies 2
  • Views 20
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Administrators

Pick the radio by what your local repeaters and nets actually use. Digital features only matter if people near you are on that system. If your area is mostly analog FM, any of the three will work fine, and ergonomics should decide it. Try to get your hands on each one, or at least study the manuals online. In a moving vehicle you want the volume, squelch, band/VFO and memory controls to be easy to find without looking. Touchscreens look nice, but physical knobs and buttons are generally easier to use while your eyes are on the road.

On power wiring, follow the manual for your radio and the fuse values it specifies. A 50 W class mobile can draw a double-digit amount of current on high power, so a thin wire or a poor crimp will drop voltage and can overheat. Run the positive lead to the battery with the fuse holder as close to the battery terminal as practical, because the fuse protects the wire along its whole run. If the radio has separate positive and negative leads with fuses, keep the supplied fuses in place. Use grommets wherever the cable passes through sheet metal. Don't rely on the cigarette lighter socket, since those circuits are shared with other loads and often have inadequate wiring for sustained transmit current.

Ground the negative lead to the battery negative or to a proper chassis ground point recommended for your vehicle. Some modern vehicles have battery monitoring systems on the negative terminal, so check the service information before connecting there. Keep the lead short and tidy, and make sure crimped connectors are properly crimped and not just squeezed.

For cross-band repeat, check the manual for each model rather than assuming. Not every dual-band mobile offers it, and the setup details differ. If you do use it, remember that the usual licensing and identification obligations still apply, and the licensed control operator needs to be able to monitor and shut it down. It's often used to extend a handheld's reach from a vehicle with a better antenna, but test it on a quiet simplex pair first so you don't interfere with an active repeater.

  • Moderators

On noise, start with the antenna and coax, because a poor antenna installation makes every other noise problem worse. A roof-center mount on a proper NMO base gives the best ground plane and keeps the antenna away from most vehicle electronics. A trunk-lip or magnetic mount can work, but expect more variation in SWR and pattern. Solder or crimp the connectors carefully, check SWR on both bands, and keep the coax away from power cables and engine harnesses where you can.

For alternator whine that follows engine RPM, check the power connection first. Poor grounds and long power runs are common causes. Ignition noise sounds more like ticking or buzzing and also follows RPM. Dash cameras, LED lights, USB chargers and DC-DC converters are classic culprits too, and they're usually easy to find. Turn accessories off one at a time while listening to a weak signal or an empty channel. Ferrite cores on a noisy accessory's power lead can help, but the cause should be found rather than just covered up. Also keep the radio's own power leads from running beside the noisy device's wiring.

As for etiquette, the main rule is that driving comes first. Use memory channels or preset frequencies, keep transmissions short in heavy traffic, and don't start long technical discussions when the road needs your attention. Listen before you key up, since mobile signals can be hard to judge when you're driving through fringe areas. Give your callsign properly, and say "mobile" if that's how people usually announce it on your local nets. Don't hog a busy repeater: if you only need a quick check-in, say so and clear. Also check your audio level. Road noise can push you to shout, and over-modulation makes you harder to copy.

Last tip for APRS or digital use: if you enable beaconing or digital modes, confirm the settings so you aren't transmitting more often than local convention suggests. A mobile that beacons constantly in a congested area is a good way to become unpopular.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.