Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Stuck around 15 WPM? Farnsworth, paddle setup, and when a decoder helps or hurts

ci_cover.jpg

Plateaus around 12 to 18 WPM are common in CW, and the cause is often a mix of habits rather than one problem. Here are the main pieces, with a question at the end for people who want to compare approaches.

Receiving. The usual advice is to learn characters at a real speed, not by counting dits and dahs. Farnsworth timing helps here. Characters are sent at their full speed, say 18 to 20 WPM, but the gaps between characters and words are stretched. Each letter then sounds like a single rhythm, and you get extra time to think. The risk is staying on stretched spacing for too long. On the air, most operators send with standard spacing, so reduce the extra gap over time until it disappears. Remember the basic timing: a dah is three dit lengths, the gap inside a character is one, between characters three, between words seven.

Copying in your head rather than writing every letter is the next step. Start with common words and callsign patterns, then whole exchanges like 5NN, TU, or a state or name. Copying a bit behind the sender, instead of chasing each letter, usually helps too.

Sending. Poor spacing is the main reason a clean-sounding fist is hard to copy. Whether you use a straight key, a bug, or an iambic paddle, regular timing matters more than raw speed. With iambic paddles, try both Mode A and Mode B on your keyer. In Mode B, releasing the squeeze after a dit-dah pair adds one extra opposite element. Some operators love that and others find it throws off their timing. Mode A stops when you release. Neither is correct, but you should know which one your keyer is set to, because it changes how a letter like C or K feels under your fingers.

Paddle tension and contact spacing also matter more than people expect. Too light and you get accidental doubles. Too stiff and you tire at higher speeds. Makers like Vibroplex, N3ZN and others sell paddles and keys with adjustable tension and gap, so it is worth reading the manual for whatever you own before blaming your hand.

Rig settings. Match your sidetone pitch to the pitch you tune the receiver to, since you will tend to zero-beat what you hear. For the filter, a width of roughly 200 to 500 Hz is typical. Going very narrow can make the signal ring and blur the keying, so start wider when practicing and tighten only when interference calls for it. QSK, or full break-in, lets you hear the band between your own elements, which is useful in a contest or a pileup. Semi break-in with a short hang time is still fine for casual operating and can be easier on a rig that switches slowly.

Decoders and skimmers. CW Skimmer and similar software are very good at pulling machine-sent calls from the noise, and they power spotting tools. For ragchews, though, decoders often struggle with fading, hand-sent irregularities, and QRM, and they can become a crutch for your ears. A reasonable use is checking a call you missed, not replacing your copy.

A few abbreviations and prosigns show up constantly: AR to end a transmission, SK to end a contact, BT as a separator, KN to invite only the station you are working, plus Q-signals like QRS (send slower), QRM (interference) and QSB (fading). Learn them as sounds, not as written letters.

So what has worked for people here when moving from stretched Farnsworth spacing to normal spacing? And do you prefer a straight key, a bug, or paddles for everyday operating?

  • Replies 2
  • Views 18
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

On Farnsworth, one practical split is to pick a character speed and leave it fixed, then only change the spacing. If the character speed keeps changing, the sound patterns never settle. Many learners choose something like 18 or 20 WPM for characters and bring the overall speed up gradually.

Contests are good practice because the exchanges are predictable. In a typical CW contest you hear the same few words over and over: the call, 5NN, a serial number or zone, TU. Cut numbers like T for zero and N for nine are also common, so it pays to recognize them as part of the rhythm. Because the content is limited, you can concentrate on callsign copy. It is a good way to build confidence without needing full conversation skills.

For the decoder question, some operators run a skimmer on a second receiver or window just to check calls and keep their own ears as the primary copy. That makes the decoder a backup rather than the main tool.

  • Moderators

On the key question, there is no single winner. A straight key makes you think about timing for every element, and that can improve your sense of spacing. Paddles with an electronic keyer give consistent dits and dahs, which makes high speeds easier on the hand. A bug like a Vibroplex gives automatic dits and manual dahs, and it has its own swing and rhythm that takes time to learn. Newcomers often find a bug harder to send cleanly than either other option.

If you use paddles, be careful about setting the keyer speed above what you can copy. It is tempting to send faster than you can receive, and then the replies come back at that speed. Keeping the sending speed close to your copying speed makes the exchange easier and avoids calling CQ at a pace that only gets answers you cannot read.

For QSK, it helps to check the rig manual for the recommended settings. Some rigs and amplifiers handle full break-in without trouble, while others click or chatter. If the relays are noisy or the amp cannot keep up, semi break-in with a slightly longer hang time is a fine compromise.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.