Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Planning a 24-hour EMCOMM station: generator or LiFePO4, and how do you keep noise and grounding under control?

ci_cover.jpg

I'm drafting a deployment plan for a 24-hour served-agency support station: one HF rig, one VHF/UHF mobile, a laptop for digital modes and logging, and a few 12 V LED lights. It will be set up in a tent or pop-up shelter at a site with no mains power. I'd like to compare notes on how to split power, antennas and noise control before I commit to gear.

The power budget so far: an HF rig running 100 W draws roughly 20 to 22 A at 13.8 V on transmit and a few amps on receive. The VHF/UHF mobile draws a few amps on receive and up to about 10 to 12 A at 50 W. The laptop and lights add a few more amps. Real duty cycle is what matters. A net-control station that listens 90% of the time uses far fewer amp-hours than the transmit current suggests. I'd rather measure it with a DC meter during a drill than guess.

The main fork is between running a small inverter generator and running a LiFePO4 battery with solar topping it off. The generator is simple and gives plenty of power for a long shift, but it brings fuel logistics, carbon monoxide risk, noise and RFI. The battery is quiet and clean, but it has finite capacity, and an undersized solar array won't keep up on a cloudy day. A hybrid, with the battery as the primary source and the generator as a backup charger, seems sensible, but I'm not sure how others split it.

On the antenna side, I'm weighing a 31 to 33 ft fiberglass telescoping mast supporting an inverted-V or end-fed half-wave for 40 and 80 m, plus a separate vertical or J-pole for VHF/UHF. For regional traffic, a low dipole or inverted-V on 40/80 m works as an NVIS antenna, and that's probably the priority. I'd like opinions on common-mode chokes, guying, and how far to keep the mast from everything else.

Finally, grounding. I've seen everything from "drive a rod and bond everything" to "a ground rod does nothing for RF." What's a reasonable, safe baseline for a temporary station?

  • Replies 2
  • Views 17
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

Think of grounding as two separate jobs. One is bonding the equipment together so there are no voltage differences between the radio, power supply and metal chassis. The other is lightning protection, and a single driven rod doesn't provide that. For a temporary station, bond your equipment together, and if you drive a rod, treat it as a static-bleed point, not protection. The real lightning plan is to watch the weather, lower the antenna, disconnect the coax and stop operating when thunderstorms get close. Nothing you can carry in a go-kit will make operating in a storm safe.

With a generator, check the manual to see whether the neutral is bonded to the frame or floating. Many portable inverter generators have a floating neutral and say so. That matters if you ever plug into a GFCI or a transfer device. Never backfeed a building circuit. Keep the generator at least 20 feet from the tent, downwind, with the exhaust pointed away. Put a battery-powered CO alarm in the shelter anyway, because wind shifts and tent walls change airflow.

For noise, turn things on one at a time and watch the S-meter on a quiet band, 40 m at night if you can. Cheap USB chargers, LED lights, MPPT charge controllers and laptop supplies are frequent offenders. A noisy device often can be fixed by moving it, shortening or rerouting its cable, or adding a snap-on ferrite. Don't wrap AC and DC cords alongside the coax. Run them at right angles where they cross.

  • Moderators

On the battery side, a few details are worth checking before you buy.

Voltage: a 12.8 V nominal LiFePO4 pack charges to about 14.2 to 14.6 V and sits around 13.2 to 13.3 V under light load, which is fine for most rigs rated for 13.8 V plus or minus 15%. Check your rig's spec. Sag under a 20 A transmit load is mostly a wire and connector problem, so use heavy enough gauge, short runs and properly crimped Powerpoles or similar, with a fuse close to the battery.

BMS behavior: when a pack's battery management system trips on over-current or low voltage, it can cut power instantly, with no slow decline to warn you. Decide in advance what your low-voltage alert is, such as a voltmeter on the bus, and what happens when it trips. Also, most LiFePO4 packs shouldn't be charged below freezing unless the pack specifically supports it, so cold-weather deployments need a plan.

Solar: use an MPPT controller with a LiFePO4 charge profile, and test it for RFI while it's actually charging. Panels in full sun can feed a lot of current, and the controller's switching noise can get into HF receive. Keep it well away from the antenna and feedline, and use short, tidy panel leads.

Antenna: put a 1:1 current choke at the feedpoint of any end-fed or dipole, and consider another where the coax enters the shelter. If the coax shield carries common-mode current, it becomes part of the antenna and picks up noise from everything in the tent. Guy the mast at three points about 120 degrees apart, keep the whole fall zone clear of power lines, and set the stakes before you raise the mast. For HF, RG-8X or similar is usually fine at these lengths. For VHF/UHF, coax loss adds up quickly, so keep that run short or use a lower-loss cable.

For the checklist, put the order of operations on paper: site survey and hazard check, shelter, generator or power placement, mast and guys, feedline, power bus, radios, noise check, then log your first contacts. Reverse it for teardown, and add a final step to walk the site for stakes, cable ties and fuel containers.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.