Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Scratch-building a multiband wire antenna: wire, insulators, feedline, chokes and how far to trust the model

ci_cover.jpg

This thread is for the practical decisions in a from-scratch wire antenna build, the ones that decide whether it works for years or needs fixing every spring. Add your own numbers and corrections. Here are the starting points, followed by a few questions.

Wire. For a fixed dipole, 14 AWG hard-drawn copper or copper-clad steel is a common choice. Copper-clad steel barely stretches, so the resonant frequency stays put as the span ages. For spans over about 80 feet, or in ice and wind, 12 AWG is worth the extra weight. Stranded insulated wire is easier to handle and coil, but the insulation lowers the velocity factor, so expect the antenna to resonate a few percent low. Bare wire is longer than insulated wire for the same frequency. Start with the cut length calculated and leave extra to fold back at each end. Trimming is easier than splicing.

Starting lengths. The usual half-wave formula, 468 divided by the frequency in MHz, gives total length in feet. At 7.1 MHz that is about 66 feet, or 33 feet per leg. At 14.2 MHz it is about 33 feet, or 16.5 feet per leg. Treat these only as a starting point. Height above ground, nearby objects, wire diameter and end-effect all shift resonance. Cut long, measure, and trim the same amount from each end.

Insulators and supports. End insulators carry mechanical load, so the wire must not be the weakest part of the joint. Pass the wire through the hole twice and twist it back on itself. Use polyester (Dacron) or another UV-resistant rope rather than nylon, which stretches and weakens in sunlight. At the center, take the strain off the solder joints with a proper center insulator or a plate with a strain-relief hole, and let the coax weight hang from the support, not the wire. Seal the coax end, because water wicks into braid and ruins the feedline from the inside.

Fiberglass poles. Telescoping fiberglass masts in the 30 to 40 foot class are popular for inverted-vees and verticals because they are non-conductive and light. Clean and tape the sections, or use hose clamps, so the pole does not collapse in wind. Do not let a wire vertical run right alongside a metal mast, because that changes the feedpoint impedance. A pole holds up much better if it is guyed or lashed at a couple of points.

Feedline and common-mode current. A coax-fed dipole wants a 1:1 current balun or a common-mode choke. Typically that is several turns of coax, roughly 8 to 12, wound on a large ferrite toroid such as an FT240 in a 31 or 43 mix. Mix choice depends on the band, so verify with a VNA rather than trusting a rule of thumb. For a ladder-line doublet, 450 ohm window line has low loss even at high SWR. Keep it away from metal, avoid sharp bends, and put the balun or choke where the line meets the tuner and coax. Some doublet lengths put a very high impedance at the feedpoint on certain bands, so check the length in a model before you cut.

Verticals and radials. A quarter-wave vertical is about 234 divided by the frequency in MHz, in feet. Elevated radials resonate and work well in small numbers. With two to four sloping radials, the feedpoint impedance moves toward 50 ohms. Ground-mounted radials need many more wires, since a handful does not make a good ground screen.

Traps vs. fan dipoles. A trap is a parallel LC circuit resonant at the upper band. It isolates the outer wire on that band and loads the antenna on the lower one. The capacitor needs a voltage rating and temperature stability suited to your power level, and each trap must be tuned and checked, for example with a grid-dip meter or a VNA with a coupling loop. Traps save space but add losses and mechanical complexity. A fan dipole costs only extra wire and spreaders. It has interaction between elements and takes more care to tune.

Measuring. Measure at the feedpoint if you can, with the choke in place. Coax loss can make the SWR at the radio end look better than the antenna actually is. Minimum SWR does not always coincide with zero reactance, so look at R and X, not just SWR. Calibrate a NanoVNA or antenna analyzer at the end of the cable you are measuring through.

Modeling. Both EZNEC and MMANA let you test a design before cutting wire. Set the real ground type, the wire conductivity, and enough segments per wire. Check the average gain test in NEC-based programs. Junctions of very different wire diameters can give bad results. Models predict trends well and absolute resonance only roughly, so build with trimming margin.

Questions for discussion: What is the best way to verify a choke's common-mode impedance on the bench? Where does a trap dipole beat a fan dipole in a real installation? And how many radials do you consider enough for an elevated vertical?

  • Replies 2
  • Views 15
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

On checking a choke on the bench: a NanoVNA can read it in a few ways. One is to put the wound choke in series between two ports and read S21, though that tends to flatter a choke at low impedance. Another is to wire the choke as a shunt with the coax shield and read the impedance directly in the shunt-through arrangement. The main thing is to look across all the bands you plan to use, because a toroid that performs on 40 m can be weak on 10 m, where self-capacitance in the winding starts to matter. Some builders stack several chokes, one for the low bands and one for the high bands, to cover the range.

Before trusting any measurement, check that the dipole is balanced. Run the VNA with the choke at the feedpoint and again with the feedline touching or draped across something different. If the readings change noticeably, there is still common-mode current on the shield. A choke is also only useful if the feedline leaves the antenna at a sensible angle. Dropping coax along one leg of the dipole invites currents onto the braid. Power matters too. A choke working into a high-SWR load heats the core, so for a doublet driven through a tuner the core size and mix need to match the power and the worst-case mismatch, not just the average.

  • Administrators

On trap vs. fan, the practical difference is usually space and the number of supports. A fan dipole can need a spreader at each element and enough room to keep the wires apart. A trap dipole is one line of wire, so it hangs from the same two points as a single-band dipole. The cost is bandwidth and efficiency. Each trap carries some loss, and on the lower band the antenna is electrically shortened, so the lower band tends to be narrower. Fan dipoles keep the full-length wire for the low band, which generally gives better bandwidth there.

For the model, a trap in EZNEC or MMANA can be represented with a parallel R-L-C load. The trap inductor's Q sets the loss, so enter a realistic Q or the model will look better than the real antenna. Build the antenna, then measure and trim each band in order, starting with the highest band, since the outer sections only matter on the lower bands.

For elevated verticals, the number of radials depends on how they are used. Two to four tuned radials for a quarter-wave with a good rise above ground gives a usable match and solid performance. Radials raised several feet above ground do not need the huge counts that buried or ground-laid radials need. Slope them downward from the feedpoint to raise the feedpoint impedance toward 50 ohms, and model it with the ground type you actually have. If the radial tips are within reach of people or animals, insulate or mark the ends, since the voltage at the tips can be high.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.