Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Bench checklist before first RF out: Pixie, Tuna Tin 2, BITX and uBITX builds

ci_cover.jpg

A lot of homebrew radio trouble comes from skipping the boring steps between "it's soldered together" and "it's on the air." This thread is for sharing a bench order for first power-up that works across simple builds: Pixie-style transceivers, Tuna Tin 2-type crystal transmitters, BITX-family SSB rigs, and uBITX kits. Add your own steps or disagree with mine.

Start with power, before any RF. Put a fuse or a current-limited bench supply in line, and add a series diode or a proper reverse-polarity scheme if the board doesn't have one. Measure the supply rails with no active parts installed or sockets empty, then check again with everything in. A direct conversion receiver or a BITX audio chain can show a lot of hum or motorboating if the supply is poorly filtered, so look at ripple with a scope if you have one, or listen with headphones. If the build uses a regulator, check that it is not oscillating. A small ceramic and a bulk electrolytic at the input and output, placed close to the regulator, usually settle that.

Next, check the oscillator on its own. For crystal-controlled designs like a Pixie or Tuna Tin 2, you want to know the crystal is oscillating on the marked frequency and not on a spurious mode. A frequency counter helps, and so does a general-coverage receiver or SDR listening nearby with the antenna disconnected. For a BITX, the VFO and BFO are separate things to verify. The original BITX20 concept runs a roughly 12 MHz IF with a VFO tuning in the 2 MHz region to land in the 20 m band, so a stray VFO harmonic or a drifting BFO shows up quickly as a distorted or offset signal. uBITX kits move that job to a Si5351 clock generator and an Arduino-class controller, so calibration of the reference frequency becomes a software and measurement step instead of a trimmer adjustment.

Always load the transmitter before keying it. Use a dummy load, not an antenna, for the first tests. A resistive load that suits the power level, and a simple RF probe or power meter, will tell you more than a stretched piece of wire. Tuna Tin 2 style transmitters and Pixies are low power, but a transistor final with no load or a bad load can still be damaged. Measure output voltage across the load and compute power (P = V_rms² / R, or V_pp² / (8R) for a sine wave). A scope with a 50 ohm termination or a probe with a known attenuation makes this easy. Don't forget that cheap scopes and cheap probes get less accurate as frequency rises.

Then look at the spectrum. This is the step most often skipped. A Pixie or other simple single-transistor stage without a proper low-pass filter can put substantial energy on harmonics. An SDR or spectrum analyzer is great for this, but never connect a transmitter directly to its input. Use a calibrated attenuator chain or a sampling tap, and know your input limits. The harmonic suppression required varies by country and power class, so check your own regulations rather than trusting a number from a forum. As a rule of thumb, a well-built multi-section low-pass filter, like a 5-element Chebyshev or similar, can make a big difference for a crystal transmitter, and for the multiband uBITX it is worth verifying output on each band instead of assuming the filters are right.

Receiver checks are different. A direct conversion receiver is simple and can be sensitive, but it has no selectivity from a crystal filter, so strong broadcast stations can leak in through detector nonlinearity and be heard as AM breakthrough. Common remedies include a front-end band-pass filter, good shielding, short leads, and good RF grounding. Microphonics from coils and wire can also be a problem. Tap on the board with an insulated tool and listen for it.

Finally, soldering and mechanical issues cause many failures that look like circuit design problems. Check for cold joints, bridges under ICs, and incompletely stripped enamel wire on toroids. Count turns on toroids the standard way, by the number of times the wire passes through the center, and double-check the core material (T37-2 and FT37-43 behave very differently). Use an adequate-temperature iron, good flux-core solder, and a magnifier. Many kit problems trace back to mislabeled parts or a misread color code, so measure resistors and small capacitors when you can.

What would you add to this order? Do you test the receiver first or the transmitter, and what is the cheapest measurement tool that changed how you build?

  • Replies 2
  • Views 14
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

I'd add one thing to the receiver section: test it with a signal source before an antenna. A simple crystal oscillator feeding a big attenuator, or a signal generator if you have one, gives you a repeatable signal for checking sensitivity and tuning range. An antenna only tells you what the band is doing at that moment, which makes it hard to tell whether a change helped.

For direct conversion in particular, check audio gain staging as a separate step. If the product detector is fine but the audio chain has too much gain, you get hiss and hum that sound like poor sensitivity. Back off the gain and compare. Also keep the audio stage's ground return away from the RF side, because a shared ground path can couple RF or oscillator leakage into the audio. A small change to where a bypass cap or ground wire lands can make a surprising difference.

  • Administrators

On the transmit side, I'd push the SWR bridge and dummy load step a little harder. A bridge is useful, but a homebrew one needs to be calibrated or at least sanity-checked. With a good dummy load it should show a very low reflected reading, and with the load open or shorted it should show a high one. If it doesn't do both, don't trust it for antenna tuning. Also, bridge readings at very low power can be misleading because diode detectors are not linear at low voltage, so test at the power you will actually use.

For the uBITX and similar modular kits, I'd also separate the questions "is the radio working?" and "is the output clean?". Plenty of boards will make power and still need attention to filtering, drive level and spurs. Keep drive within a range where the final is not being compressed, check each band's low-pass filter setting, and look at the output with an SDR through a proper attenuator. A clean-looking waveform on a scope can still hide harmonics that a spectrum view makes obvious.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.