Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

From FM Birds to Linear Transponders: Doppler, Tracking, Antennas and What to Expect on Each Pass

ci_cover.jpg

This thread is a working overview of how the common amateur satellite types differ in practice, and where operators usually get stuck when moving from one to the next. Frequencies and satellite status change over time, so check the AMSAT status pages and your tracking software's current transponder database before relying on anything below. The numbers here are the commonly published ones and are meant to explain the concepts.

FM birds (AO-91, AO-92, SO-50). These are single-channel crossband FM repeaters, so one station at a time can use the transponder. AO-91 and AO-92 have been published with a 70 cm uplink (around 435.250 and 435.350 MHz) and a 2 m downlink (around 145.960 and 145.880 MHz), with a 67.0 Hz CTCSS tone on the uplink. SO-50 is the reverse: a 2 m uplink near 145.850 MHz and a 70 cm downlink near 436.795 MHz. It has historically needed a short arming tone (74.4 Hz) before the 67.0 Hz tone, so read the current access instructions. Because FM satellites are crowded, passes usually consist of short exchanges: callsign, grid square, signal report if there is time. Grid squares are four-character Maidenhead locators such as CN87 or FN31, and operators commonly chase rare grids.

Doppler. The shift scales with frequency and radial velocity. For a typical LEO pass it is roughly plus or minus 3 kHz on 2 m and about plus or minus 9 to 10 kHz on 70 cm. It starts high on approach (the signal arrives above its nominal frequency), crosses zero at closest approach, and goes low as the satellite recedes. On FM this matters because a downlink 8 kHz off will sound distorted or fall outside a narrow receiver filter. Many operators correct only the 70 cm side in steps and leave the 2 m side nearly fixed. Rig memories with a few frequency offsets also work, but software-controlled CAT tuning makes it much easier.

Linear transponders (RS-44, and others). A linear transponder retransmits a slice of spectrum, so many SSB and CW signals can coexist. RS-44 has been published as an inverting linear transponder with a 70 cm uplink around 435.610 to 435.640 MHz and a 2 m downlink around 145.935 to 145.965 MHz, with a beacon near the bottom of the downlink. Inverting means that if you tune your uplink higher, your downlink moves lower, and sideband is flipped. The usual workflow is to pick a spot on the downlink where you want to be heard, let the software hold the uplink so that you land on that spot, and fine-tune with the VFO only. You need to hear your own downlink (full duplex or two receivers), and your uplink power should be modest. If you are louder than the beacon, you are too loud, and you are also eating the transponder's power budget. RS-44's orbit is higher than the typical cubesat, so passes tend to be longer and the Doppler changes more slowly, which makes it a popular first SSB/CW bird.

ISS. The ISS APRS digipeater is on 145.825 MHz at 1200 baud AFSK, using the ARISS-style alias path. The ISS crossband voice repeater, when it is enabled, has been published as 145.990 MHz up (with 67.0 Hz CTCSS) and 437.800 MHz down. Both depend on crew and operational schedules, so do not assume they are active. The ISS has a short pass duration and quickly changing Doppler, and APRS in particular is limited by collisions, since everyone transmits on one channel.

QO-100 (Es'hail-2). This is a different kind of operating. It is geostationary, so there is no Doppler from orbital motion and no pass planning. The narrowband transponder uses an uplink around 2400.0 to 2400.5 MHz (2.4 GHz) and a downlink around 10489.5 to 10490.0 MHz (10 GHz), with coverage over a large footprint spanning Africa, Europe, the Middle East and parts of Asia. The challenges are the microwave hardware: a dish, a feed for 2.4 GHz, an LNB on 10 GHz, and frequency stability, since a free-running LNB oscillator will drift. Many stations use a GPS-disciplined or otherwise stabilized LNB, and a beacon as the reference.

Tracking software. Gpredict is free and cross-platform, and can drive a rig through Hamlib's rigctld and a rotator through rotctld. SatPC32 is a long-standing Windows program with wide rig and rotator interface support. Both depend on up-to-date Keplerian elements (TLEs). Old elements cause errors in timing and pointing, and weeks-old data for low-orbit satellites can be noticeably off. Set your station location correctly, including your grid or latitude and longitude, and keep your computer clock accurate.

Antennas. A handheld dual-band Yagi like the Arrow style is a common starting point for FM satellites. You point it by hand, so there is no rotator cost, but you must manage radio, logbook and pointing at the same time. Because these antennas are linearly polarized and the satellite is spinning or tumbling, expect signal fading. Larger Yagis on an azimuth/elevation rotator give more gain and allow SSB/CW work, but pointing accuracy and cable losses matter more. A preamp at the antenna is helpful for 70 cm downlinks but is not magic: it cannot fix a bad feedline or a noisy location.

Questions for the thread: what is your setup for tracking Doppler on linear birds? Do you prefer manual tuning or software-controlled tuning? And which step actually limited you when you started: antenna pointing, rig control, or simply learning to hear your own downlink?

  • Replies 2
  • Views 17
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

On linear birds, the thing that usually breaks people's first few attempts is not the antenna, it is the tuning loop. If you chase your own signal with the main dial while the software is also moving the uplink, you create a feedback problem. A cleaner method: let the software handle Doppler for the downlink you are listening on, and make only small corrections with the RIT/XIT or sub-VFO. Then the frequency you hear stays put, and the other station will not need to chase you. On an inverting transponder like RS-44, this also keeps the sideband logic straightforward: you transmit one sideband, and you will hear the opposite on the downlink.

Also, test the full duplex path before you use a pass. Listen to the beacon, transmit at low power into a dummy load or a lower setting, and see whether your receiver front end desenses. 2 m and 70 cm are close enough for some rigs, and receive overload or desense from a nearby transmitter can look like a weak satellite.

  • Moderators

For FM passes, one practical point is to separate the two jobs: pointing and operating. With an Arrow-style Yagi, the elevation mismatch with the satellite at low angles is rarely a problem; at high elevation passes, you must change your pointing fast near closest approach because the satellite sweeps quickly across the sky. Plan the pass in Gpredict or SatPC32 before AOS (acquisition of signal), write down the maximum elevation and the time, and know whether the pass is east or west of you. Low passes (under about 15 degrees) are often more trouble than they are worth with ground clutter and trees.

For logging, keep the exchange minimal: callsign and grid, perhaps a quick report. If you are using the ISS APRS digipeater, remember it shares one frequency with everyone else. Long beacon texts or frequent transmissions create collisions, so keep packets short. And if you are using a rotator, check that your software and controller agree on the protocol (many use GS-232 style commands) and the elevation range. A rotator that stops at 180 degrees of elevation is a different setup from one that goes to 90 only, and it affects how you handle overhead passes.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.