Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Band plan vs. license privileges: how do you work out where you can operate, and how close to the band edge is too close?

ci_cover.jpg

I'm trying to build a mental map of the amateur bands from 160 meters up through 33 centimeters, and I keep mixing up what is legal and what is just convention. Some of the questions I'd like help sorting out:

First, when the ARRL band plan shows a CW/data segment and a phone segment, is that a rule I can be cited for breaking, or a gentleman's agreement? How does that differ from the sub-band limits tied to my license class?

Second, how should I think about band edges? If a privilege ends at a certain frequency and I'm on USB or LSB, where should the dial sit so my signal doesn't spill over?

Third, what's the story with the 60 meter channels, and why do some bands seem to have different edges in other parts of the world? I'd also like a quick sanity check on the simplex calling frequencies on 6 m, 2 m, 70 cm and 33 cm, and where weak-signal and FM operation tend to live.

Please correct anything that has changed. I know rules get updated, so pointers to where to verify are welcome too.

  • Replies 2
  • Views 16
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Administrators

The most important distinction is that there are two layers. Your license privileges come from the FCC rules (Part 97 in the US) and are legally binding. Those cover which frequencies, which modes and how much power your class allows. The ARRL band plan is voluntary. It is a consensus on how to share the spectrum so CW, digital, SSB, beacons and satellite traffic don't trample each other. You won't get a notice for running SSB in the middle of the FT8 watering hole, but you'll be unpopular and probably unintelligible. Stepping outside your class privileges is a different matter.

On HF, the pattern by class is roughly this. Technicians get CW privileges in segments of 80, 40 and 15 meters, plus 10 meters (CW/data in the bottom part, SSB in the upper part of the lower portion) with a 200 W PEP limit. Generals get most of each HF band, with phone segments that start higher than Extra's on 80, 40, 20 and 15 meters. Extras get everything, including the bottom slices of the phone bands. Because the exact edges differ band by band (and 30 meters is CW/data only with a lower power limit), don't memorize them from a forum post. Print the current FCC privileges chart or ARRL's band chart and check it when rules change.

The band edge question is mostly about sidebands. The dial frequency on SSB is the suppressed carrier, not the edge of your signal. On LSB, the signal extends below the dial, so near the bottom of a phone segment you need to sit a few kHz inside it. On USB, the signal extends above the dial, so near the top of a segment you need to stay a few kHz below the edge. A voice signal commonly occupies around 2.4 to 3 kHz, and the dial readout may have some error, so leave extra margin. Digital modes are similar. The transmitted audio tone offset is added to the dial frequency, so your actual RF edge is the dial plus the highest tone in the passband.

The 60 meter band is different in the US because it has historically been channelized rather than being a continuous band. General and Extra operators can use a handful of specific channels, and the rules call for USB for voice, a limited occupied bandwidth, and a low ERP limit relative to a dipole. The dial frequencies commonly cited are 5330.5, 5346.5, 5357.0, 5371.5 and 5403.5 kHz. Check §97.303 and current ARRL guidance before relying on that list, since 60 meter rules have been revised over the years and may change again. Other countries often have different 60 meter allocations, so you can't assume the US channels exist elsewhere.

  • Moderators

On VHF/UHF the band plan matters even more, because FM voice, weak-signal SSB and CW, repeaters, satellites and beacons are all squeezed into relatively small slices. The usual pattern is that the very bottom of each band is for weak-signal work (CW and SSB, sometimes EME), with digital and beacons nearby, and FM simplex and repeaters above.

On 6 meters, the weak-signal area is at the bottom of the band. The CW-only portion is at the very bottom, and 50.1 to 50.3 MHz is the usual SSB/CW area. The DX window is around 50.110 MHz, and 50.125 MHz is the common domestic SSB calling frequency. FT8 is typically near 50.313 MHz. FM simplex activity is higher up, with 52.525 MHz commonly used as a national FM calling frequency.

On 2 meters, 146.52 MHz is the national FM simplex calling frequency. Many people use it as a rendezvous: you call, then move to another simplex channel to talk. Repeaters sit on pairs that vary by region, which is why your local frequency coordinator's list matters. For weak-signal work, 144.200 MHz is the SSB calling frequency, and FT8 is commonly on 144.174 MHz. On 70 cm, 446.0 MHz is the national FM simplex calling frequency, and 432.100 MHz is the usual SSB/CW weak-signal calling area. On 33 cm, activity is much thinner and is concentrated around the weak-signal calling frequencies in the ARRL plan (902.100 MHz, with 903.100 MHz as an alternate). Check the plan if you want to try it. Technicians have full privileges on all of these VHF/UHF bands, which is one reason they are such a good place to explore.

Two caveats are worth keeping in mind. First, 70 cm and 33 cm are shared bands, and amateur operation there can be secondary to other services. In some areas there are geographic or power restrictions on 70 cm, and 33 cm shares spectrum with unlicensed devices, so noise and interference can be a real issue. Second, allocations differ by ITU region. The US is in Region 2. Examples include 40 meters, which is 7.0 to 7.3 MHz in Region 2 but narrower elsewhere (7.0 to 7.2 MHz in Regions 1 and 3), and 33 cm, which is a Region 2 allocation that isn't available in Region 1. 70 cm is 420 to 450 MHz in Region 2 but 430 to 440 MHz in Region 1. Your US license does not automatically grant operating privileges abroad. Look into the specific reciprocal or CEPT arrangements before you travel. IARU band plans for each region are also voluntary, like ARRL's, but they are what most operators outside the US follow.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.