Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Small lot or HOA: EFHW, OCFD, doublet, vertical or loop? What actually decides the result

ci_cover.jpg

This comes up constantly: a lot of roughly 50 x 80 ft, a house in the middle, no tower, and either a covenant or a spouse who objects to anything that looks like an antenna. The question is usually "which antenna should I buy or build?" The better question is what you can hang, how high, and what feedline and common-mode problems come with it. Here is a framework for comparing the usual candidates.

Height and geometry come first. A horizontal wire at 25 to 35 ft is low for 80 and 40 m. It tends to radiate at high angles, which is fine for regional contacts and poor for DX. On 20 m and up, the same height starts to look reasonable. An inverted V, with its apex at the best support you have and its ends sloping down, saves horizontal space and needs only one tall support. The cost is a little pattern and bandwidth change and a feedpoint impedance that drops toward 50 ohms or below as the included angle closes. Trim for resonance by measurement, not by formula.

EFHW. The feedpoint of a half-wave wire at its end is high impedance, commonly in the low thousands of ohms depending on the installation. A 49:1 or 64:1 transformer brings that down toward 50 ohms. The advantages are one support, a single wire, and multiband operation on harmonically related bands (for example 40/20/15/10 from a 40 m wire). The catch is that an end-fed wire has no deliberate counterpoise, so the coax shield often becomes one. Without a common-mode choke, you may see SWR that changes when you move the coax, RF on the shack equipment, and noise pickup. A low SWR reading on an EFHW can be real or can be the feedline doing part of the radiating, so check it with a choke in place.

OCFD (Windom style). Feeding a half-wave wire about one third of the way along gives a more moderate impedance, often handled with a 4:1 current balun. It covers several bands, but the harmonic feedpoint impedances are not uniformly benign, and patterns on higher bands are lobed because the wire is multiple half-waves long. Balun core saturation and heating matter more at high SWR or high power.

G5RV and doublets. A G5RV is a 102 ft top with a ladder-line matching section, designed for good behavior on 20 m and tuner-assisted on other bands. A general doublet is any center-fed wire of roughly 100 to 130 ft or more, fed with open-wire or ladder line and used with a tuner that can handle balanced loads, or a good 4:1/1:1 balun-plus-tuner arrangement. Ladder line has very low loss even at high SWR, which is why a doublet can be the most flexible compromise. The real work is getting the line away from the house cleanly and choosing a length that avoids extreme impedances on your most-used bands.

Coax loss and SWR. A common mistake is treating SWR as a performance number. A dummy load is 1:1 and radiates nothing. Coax loss rises with frequency and with mismatch. Thin coax such as RG-58 loses noticeably more than RG-213 or low-loss 50 ohm cable at 14 MHz and above, and a high SWR on a long run multiplies the loss. If the tuner is at the radio and the antenna is a high-SWR multiband wire, the feedline matters more than the antenna model suggests.

Verticals. A vertical is a small-footprint option and can have a low takeoff angle. Its weakness is the ground system. A ground-mounted quarter-wave needs many radials, with 16 or more as a common rule of thumb for low loss. An elevated vertical can work with fewer resonant radials, often 2 to 4 per band. Sloping radials raise the feedpoint impedance toward 50 ohms. In a small yard, a vertical with a poor ground system can trade away the advantage of its low angle through ground loss.

Magnetic loops. A small loop can be a practical indoor, attic or balcony choice and often reduces local electrical noise. The tradeoff is efficiency, which depends heavily on loop diameter relative to wavelength, conductor loss and capacitor quality. Bandwidth is narrow, so you retune when you change frequency, and the loop's high voltage requires proper spacing and parts. Expect lower efficiency on 40 m and below, where a small loop is electrically very small.

Yagis. A multielement beam gives gain and front-to-back advantages, but it needs a tower or mast, a rotator and permission to put it up. For many HOA situations it is not on the table, and a good wire and a modest vertical are the realistic baseline.

Which tradeoffs have bitten people most in constrained installations: common-mode currents, ground losses, or tuner and feedline losses? And for HOA situations specifically, what has been the least visible practical option for you? Note that FCC PRB-1 covers state and local regulation, not private deed restrictions, so check your actual covenant text.

  • Replies 2
  • Views 15
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

Common-mode current is the sneaky one, because the SWR meter can look great while the coax is doing half the radiating. With an EFHW especially, I'd put a proper choke at the feedpoint and, if the run is long, another choke where the coax enters the shack. A choke made of coax wound on a ferrite core needs the right material for the band. Mix 31 and 43 behave differently across HF, and a choke that is good on 20 m can be mediocre on 80 m. If you can, measure the impedance of the choke rather than assuming.

For comparing antennas, avoid judging by who you hear on a single band. Use a consistent method: WSPR or RBN spots over several days at similar times, or a switchable A/B setup with a second antenna and S-meter readings on a steady signal. Your noise floor will often change the result more than the antenna's gain. A quieter antenna that hears slightly weaker signals can still give better readable copy.

On doublets: with open-wire line, I'd avoid a feedline length that happens to be a multiple of a quarter wave on your busiest band, because it can bring extreme impedance to the tuner. Changing the line length a few feet can make the tuner's job a lot easier, and the effect is easy to model with free software like 4nec2 or MMANA-GAL before cutting anything.

  • Moderators

For a tight lot I'd think in terms of two buckets. The first is a horizontal wire as high as you can get it, which favors medium-range work and low noise from the ground. The second is a vertical with a real counterpoise, which favors lower angles. If you can only choose one, the deciding factor is usually which supports you actually have. A tall tree, a flagpole or a chimney mount changes the answer more than the antenna type does.

On the vertical side, a flagpole or a thin telescoping mast can disappear visually, but you still need the radial system. A set of elevated radials running along a fence or tucked just above the grass can be more efficient than a few short ground radials. Keep in mind that the radials carry current and are not harmless, so keep them out of walking areas for safety and RF exposure reasons.

For stealth wire, thin dark insulated wire against sky or trees is far less visible than white or shiny wire, and a wire that is not a straight line can still work. The cost is some pattern distortion and lower efficiency if it bends too close to metal gutters or house wiring. A magnetic loop may be a good complement for local noise rejection, but don't expect it to match a half-wave wire at 40 m. If the main goal is 20 m and up, a loop of reasonable size can be a surprisingly practical option. Below that, a wire with a decent feedline will usually win on signal strength.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.