Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

SSB audio setup: mic gain, ALC, compression and EQ for a clean signal that still cuts through on DX

ci_cover.jpg

Most SSB audio problems come from the same few settings: too much mic gain, too much processing, or too much low-frequency energy. This thread is for comparing approaches and sharing the order in which you set things up. Here is a baseline to argue with.

Start with the microphone and position. Before touching any menu, fix the acoustic side. Keep the mic about 2 to 4 inches from your mouth, and slightly off-axis if it pops on P and B sounds. A hard-walled room adds reflections that no equalizer fully removes, so a rug, curtains or a mic closer to your mouth often helps more than any menu setting. Check whether the mic is dynamic or electret. Many electret and headset mics need bias voltage from the rig, and a wrong setting gives low output or noise.

Set mic gain by the ALC, not by feel. ALC (automatic level control) protects the final stage from being overdriven. If your voice peaks push the ALC far into its zone, you are overdriving the audio chain. That means distortion, wider splatter and a signal that sounds harsh on the other end. A common approach is to speak at normal volume with processing off and raise mic gain until the ALC just flickers on the loudest syllables. On most rigs, if the ALC is pegged continuously, back off. If you run an amplifier, watch for ALC feedback from the amp as well, since that is a separate problem from mic gain and the drive level is often the cause.

Compression and the speech processor. Processing raises average power relative to peak power, which is what helps a weak signal be copied. The gain is not free. Past a modest amount of compression, background noise rises, sibilance gets harsh and intelligibility drops. Many operators find that around 3 to 6 dB of compression on the rig's compression meter is a sensible range. Check your manual, because meters are not calibrated the same way across brands. Note also that RF clippers and AF compressors behave differently. RF clipping can add distortion products that are filtered but still audible if overdone.

Use the monitor, but know what it is telling you. Use headphones with the monitor on at a low level so there is no feedback. On many rigs the monitor takes audio after the processing and EQ, so it is a good guide to how your voice has been shaped, but it does not show what the RF sounds like after the transmitter. For a real check, ask a local station for an honest report, or listen on a remote receiver such as a WebSDR or KiwiSDR if you can reach one within range. A recording of your own signal reveals things you will not hear live.

Transmit equalizer and bandwidth. SSB voice intelligibility lives mostly between roughly 300 Hz and 2.7 kHz, and consonants sit toward the upper end. Trimming deep lows reduces rumble and saves power for the part of the spectrum that carries information. A gentle lift in the 1.5 to 3 kHz region often helps readability, but too much sounds thin and sharp. Many modern rigs allow a narrower or wider TX bandwidth. Wide settings, say 3.0 kHz or more, sound natural for a casual local chat on a quiet band, while about 2.4 kHz or a bit less is a better fit on crowded bands and in pileups. Be considerate: your occupied bandwidth affects neighbors.

Sideband convention. Use LSB below 10 MHz (160, 80 and 40 meters) and USB above 10 MHz (20, 17, 15, 12, 10 and 6 meters). The 60 meter channels are used with USB in many regions, but check the rules and band plan for your country. If you are on the wrong sideband, the other station may be unable to copy you properly without retuning.

Working weak stations and DX. On receive, a 2.4 kHz filter is a good starting point, and many operators drop to around 1.8 to 2.1 kHz when QRM or noise is heavy. Use passband shift or IF shift to move the window away from an adjacent signal rather than just shrinking it. Keep the AGC suitable for the band, and use the preamp, attenuator and RF gain deliberately rather than leaving them wherever they were. Noise reduction can help, but heavy settings add artifacts that can hide a weak voice. On transmit, speak clearly and slightly slower, and use standard phonetics for your callsign, especially when conditions are poor. Repeat the callsign suffix, not the whole thing endlessly, and listen to where the DX station is working before you call.

What order do you set things up in, and where do you stop adding processing? If you have rig-specific tips on EQ curves or compression levels, include the model and what the manual says so others can compare apples to apples.

  • Replies 2
  • Views 17
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

One addition on ALC: a lot of people set it once and never revisit it after changing mics or turning the processor on. Processing changes how much average level reaches the modulator, so the mic gain that looked right with the processor off can overdrive the chain with it on. Redo the ALC check with processing engaged, saying the same test phrases at the same distance from the mic.

Also check the ALC reading on each band if you run an amplifier. A little ALC action from the radio is usually acceptable on many rigs, but if the amp is feeding back its own ALC voltage, the audio will sound compressed and mushy even though the radio's settings look fine. In that case reduce drive until the amp's output stops growing faster than the distortion.

For sideband, remember that tuning the band edge on LSB or USB shifts where your signal actually sits. Keep your suppressed carrier frequency and the whole audio bandwidth inside the allowed segment, not just the dial reading.

  • Moderators

Good baseline. On the EQ question, I would treat any curve as a starting point for your voice and mic, not a universal recipe. A lift that makes a deep voice clearer can make a naturally bright voice harsh. A practical method is to make short recordings of yourself with one change at a time, such as cutting below 300 Hz, adding a bit around 2 kHz, or reducing compression. Then compare them, ideally listening through small speakers or an SDR the way a distant station would hear you.

For DX, the other half is receive discipline. A narrower filter helps only if you tune accurately. Many weak signals disappear because the filter is centered a few hundred hertz off, so try shifting the passband before blaming the band. If the station you are chasing is very weak, drop the noise reduction a notch, use a slower AGC if it stops the band noise from pumping, and listen for several exchanges before calling so you know whether the operator wants a callsign only or a full report.

And if a station tells you that you are splattering or sound distorted, do not go straight for more compression. Lower the mic gain and drive first, then rebuild the audio chain stage by stage.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.