Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Winlink over radio: a working setup order for Winlink Express, gateways, sound card modems, P2P and forms

ci_cover.jpg

This thread is meant as a baseline for people getting Winlink Express working over radio, and as a place to correct it. Most setup problems come from doing steps out of order, so this is the sequence that tends to isolate faults fastest.

1. Start with Telnet. Install Winlink Express, enter your callsign, and set your Winlink password. Then run a Telnet Winlink session over the internet. This confirms that your account works and that you can send and receive through the CMS before any radio is involved. Passwords are case-sensitive, and it is worth setting a password recovery address now rather than after you are locked out. The password authenticates your station to the system. It does not encrypt your message content, so write every message as if it could be read by anyone.

2. Download the gateway list while you still have internet. Winlink Express keeps a channel list of RMS gateways: callsign, frequency, mode, grid square and distance from you. You refresh it online and it is cached for later use. If you wait until the internet is down, you may only have an old list. For VHF/UHF packet or VARA FM you are looking for gateways within line-of-sight or repeater range. For HF you want a spread of stations at different distances, because propagation, not distance, decides what works. The HF channel selector can give propagation estimates, but treat them as hints. Also check whether a listed HF frequency is a dial frequency or a center frequency, and make sure your rig control and mode settings match what Winlink Express expects.

3. Choose the session type to match the radio and the path.

Packet Winlink is the classic 1200 or 9600 baud connection to an RMS Packet gateway, using a hardware TNC or a software TNC through KISS. VARA FM is a sound card modem for VHF/UHF that is much faster than 1200 baud packet when the link is solid. VARA HF is the HF counterpart and adapts its speed to conditions. The unregistered versions of VARA are speed-limited, and a license removes that limit. ARDOP is a sound card HF mode and is a common choice when you want an open-source option, with selectable bandwidths. Pactor needs a supported hardware modem, and Pactor 3 and 4 need SCS modems, so it is mostly a fixed-station or maritime-style choice rather than something you add with a free download. Telnet Winlink runs over the internet, and Telnet P2P is the same idea between two stations on a network.

4. Know what Radio-only and P2P mean. Normal gateway sessions end up on the Winlink system, which is internet-connected. Radio-only is about keeping traffic on the radio path, so it can still be handled if internet is not available at the gateway or if you do not want the message going to the internet. Check how your Winlink Express version labels and handles this, and remember that recipients and routing then become more limited. P2P (peer-to-peer) is a direct connection between two stations with no gateway and no CMS. One station listens, the other calls it, and you can do it over packet, VARA, ARDOP or Pactor. It is the fallback that keeps working when there is no gateway in range, but both operators have to agree on mode, frequency, and who is listening.

5. Test your audio and PTT before your first on-air session. For sound card modes you need the right audio device, a clean transmit level, and reliable PTT (CAT, serial RTS/DTR, GPIO/CM108-type interface, or VOX as a last resort). Turn off Windows audio enhancements and any rig speech processing. Aim for no visible ALC action on the transmitter. More drive causes distortion that hurts decoding and wastes your power. I will leave the finer points of this to replies.

6. Practice on a schedule. Winlink Wednesday is a weekly exercise where operators send practice check-in messages. Read the current instructions from the people who run it before you take part, because the exact address and format are not something to guess. Weekly practice finds the real problems: stale gateway lists, wrong COM port, an audio device that Windows renamed after an update, or a password you forgot.

What have I missed in this order? In particular, I am interested in how people decide between VARA FM and plain packet for local emergency-comms drills, and how they handle forms and attachments for served agencies.

  • Replies 2
  • Views 18
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

On the sound card and TNC side, most failures I see described fall into four buckets: wrong audio device, wrong PTT method, overdriven audio, and a software TNC that is not actually running.

For packet with a software TNC, the chain is: radio audio into the sound card, a software modem that does the AFSK and AX.25 work, then a KISS connection to Winlink Express, and finally a PTT method that the modem or the program is allowed to control. The common mistake is two programs trying to key the radio, or the modem expecting a different COM port than Winlink Express does. Pick one owner for PTT and one owner for the audio device. If you use a virtual COM port pair or a TCP KISS connection, check the exact option your Winlink Express version offers, because the supported choices have changed over the years.

For VARA HF and VARA FM, the VARA modem is a separate program that Winlink Express talks to. It has its own audio device, PTT, and sometimes CAT settings. If you set up Winlink Express but never opened the VARA settings, you will get a session that starts and then does not key or does not decode. Set the soundcard input and output in VARA, then use its tuning display and level indicators to set receive audio so it is neither buried nor clipping. On transmit, raise drive until you see power on the meter, then back down. A clean 100 W signal is not the target for a 2300 Hz wide data mode on a typical transceiver. Look at ALC and keep it from moving.

For HF, use USB, and keep the rig's noise reduction, compressor, and wide filtering features out of the way. For ARDOP, the bandwidth you select should match what the gateway is configured for. A mismatched bandwidth is a common reason for connection attempts that go nowhere.

One more detail that gets overlooked: if the gateway list shows a frequency for the station you want, confirm whether it is a dial or center frequency and how your software handles it. A 1.5 kHz offset error is the kind of mistake that looks like a dead band.

If a connection fails, change one thing at a time. First prove the radio chain with a known-good test, then the modem, then the gateway, then the path. Trying a different gateway or a different time of day often tells you more than changing settings.

  • Moderators

On message handling, the main habit to build is to keep messages small and plain. Radio links have limited throughput, and an attachment that is harmless over the internet can dominate a short HF session. Send text where text will do. If you need an image, reduce its size first, and ask whether it needs to be sent over radio at all. Keep in mind that packet, VARA HF, ARDOP and Pactor all have very different speeds and that conditions change them further.

Winlink Express keeps an Outbox, so you can compose messages offline and send them in one session. That is the efficient way to work: write, attach, check addresses, then connect. Posting a message does not mean it has been delivered, only that it is queued for the next session. Check the Sent items and the session log after each connection, because the log shows which messages went out and which came in. For recipients, a Winlink address or an internet address can be used, but the recipient on the other end may have mail filters, so for important traffic confirm receipt another way.

Forms are where Winlink is useful for served-agency work. The standard templates include the ICS-213 General Message. Using a form instead of free text makes the message structured: To, From, Subject, Message, Approved by, and so on. The form data travels as compact data with the message, and the receiving operator uses the form viewer to see it in the intended layout. If the recipient does not have the same tools, the message may still be readable but not as intended, so agree on the process before an incident, not during it. Do not edit the template in ways that break how the form data is read. If your agency needs a customized form, work with whoever maintains the templates and test it end to end.

For P2P, set the session type to match your partner and decide in advance who listens. Messages exchanged P2P do not pass through the CMS, so a P2P message is not a replacement for a message that must reach an internet address, unless one of the stations later connects to a gateway and forwards it. That is a workable emergency pattern: collect traffic locally by P2P, then relay it when a gateway or internet link returns.

Finally, if you take part in Winlink Wednesday, treat it as a drill and not just a check-in. Try a different mode each week, use a gateway you have not tried, send a form, and read the session log afterward. Over time you build a personal record of which gateways and bands work from your location, and that is more valuable than any list.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.