Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Scratch-building wire dipoles and verticals: wire, chokes, support points, and how far to trust SWR and models

ci_cover.jpg

This thread is for the practical decisions that come up when you build an HF antenna from raw materials rather than buying a kit. I'll start with a rough order of operations, and then I'd like to hear where others disagree.

Start with the support plan, not the wire length. The wire length can be trimmed, but the places where you can hang things cannot. Decide the apex or center height, where the ends will land, and how the feedline will leave the antenna. A dipole at 30 to 40 feet is a very different antenna from one at 15 feet, and the resonant length shifts with height, nearby trees, and wire insulation. The familiar 468/f(MHz) formula gives a half-wave length in feet. For 7.1 MHz that is about 66 feet total, so each leg is about 33 feet. Treat that as a starting point. Cut long, fold the excess back at the ends, measure, and prune.

For wire, 14 AWG hard-drawn copper is a common choice for long permanent spans, because it resists stretching. Soft-drawn copper stretches over time and moves your resonance. Copper-clad steel is strong, but it has more skin-effect loss at lower frequencies, and it can be stiff and springy. Insulated stranded wire is easy to handle and lowers the resonant frequency a few percent compared with bare wire, so allow for that. Wire gauge matters less for efficiency than most people expect at HF. A dipole made from 14 AWG instead of 18 AWG will have slightly broader bandwidth and better mechanical life, but it won't be dramatically stronger on the air. What fails in the field is usually the connection or the strain relief, not the conductor.

Insulators and supports are where many builds fail. Use UV-resistant polyester or similar low-stretch rope at the ends. Avoid cotton, which rots, and cheap nylon, which stretches and weakens in sunlight. The center insulator should take the wire tension, not the solder joint or the coax connector. Run the wire through the holes, twist it back, and then solder, so the joint carries no load. The coax should hang from a strain-relief point, because its weight pulls on the center. A fiberglass pole at the center or ends is useful because it doesn't detune the antenna the way a metal mast does. Poles flex, so leave some slack for wind loading.

Feedline and common-mode current deserve separate attention. A coax-fed dipole should have a 1:1 current balun or choke at the feedpoint. The goal is to keep RF off the outside of the shield, and a choke with high impedance does this better than a low-loss one. Ferrite beads or toroids of a suitable mix, such as type 31 or 43 in many builds, wound with several turns of coax, are one common approach. Another is a coiled-coax choke, which works but tends to be narrower in bandwidth. If you feed the dipole with 450-ohm window line instead, you can use it on multiple bands with a tuner, but keep the line away from metal gutters and walls, and expect a balun or choke at the transition into the shack.

Verticals have their own questions. A quarter-wave vertical for 20 m is about 16.5 feet, which fits nicely on a telescoping fiberglass pole with wire taped along it. The radial system matters more than the radiator. Raised radials, sloped or horizontal, can be fewer and resonant; ground-mounted radials usually need more, and many people use a larger quantity of mixed lengths. The feedpoint impedance changes with radial angle and count, which is why the SWR varies from the textbook number.

Finally, how much do you trust a low SWR? It tells you the match at the point of measurement, not how much power is being radiated. Coax loss can make a poor antenna look good, and a modeled pattern can look wonderful if the ground or segmentation is wrong. What methods do you use to confirm that an antenna works, rather than just matches?

  • Replies 2
  • Views 14
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

On measuring: if you can, take the SWR or impedance reading at the feedpoint, or at a length of coax that you know the loss of, and with the choke already installed. Without a choke, the coax shield becomes part of the antenna, and the reading can change when you move the cable or touch it. That is a useful test in itself. If the reading drifts as you handle the feedline, you probably have common-mode current.

Also, minimum SWR and resonance are not always the same frequency, especially with lossy traps or a short vertical over poor radials. An antenna analyzer that shows R and X helps more than a single SWR figure. Reactance crossing zero shows resonance, and the resistance shows what the feed has to match. For a multiband doublet on ladder line, measure at the tuner end only if you accept that the line length transforms the impedance. A very high or very low value at some lengths is normal and not a sign that the antenna is broken.

  • Moderators

For modeling, EZNEC and MMANA-GAL are both useful, but each tells you only what you put in. In either one, check that your segments are short enough relative to wavelength, especially where wires bend, join, or change diameter. Place the source on a segment that is properly connected to both legs. Choose a realistic ground model, because a free-space result and a result over average ground at 15 feet can look quite different. The EZNEC demo has a segment limit, so a complicated antenna may need the full version, while MMANA-GAL is a free option that many builders use for simpler wire shapes.

The biggest modeling trap is leaving the feedline out. If you want to explore common-mode current, add a wire representing the coax and see how pattern and feedpoint impedance change with its length and routing. For traps, model the coil and capacitor as loads, but treat the result with caution. Real traps have finite Q, so a model may show more efficiency than the built antenna. Use the model to choose starting lengths and compare designs, then use measurements on the real wire to adjust. When the two disagree, check height, wire diameter and insulation, and nearby objects before you decide which one is wrong.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.