Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

2m/70cm antenna choices: whip, J-pole, collinear or yagi, and what actually matters once it's installed

ci_cover.jpg

This is a starting point for comparing common VHF/UHF antenna types on practical terms rather than catalog gain numbers. Most problems with 2 m and 70 cm stations come from the installation (feedline, connectors, ground plane, polarization, height) rather than from the antenna type.

Simple verticals. A quarter-wave whip is about 19 inches on 2 m and about 6.5 inches on 70 cm. It is mechanically simple and tolerant of imperfect ground planes, and its pattern is very predictable. A 5/8-wave whip has a lower takeoff angle and a few dB more gain than a quarter-wave under good conditions, but it needs a matching coil or network at the base and a reasonable ground plane to perform as advertised. On a small mag mount or a roof-edge NMO mount the real pattern can be skewed, and the gain on paper may never show up. A 5/8 whip on a metal roof is a good match. The same whip on a fiberglass trunk lid with a tiny ground plane is a poor one.

J-pole and Slim Jim. Both are end-fed half-wave antennas with a quarter-wave matching section. Their gain is close to a half-wave dipole, so expect roughly 0 dBd and not the 3 dB or more some listings claim. They need no radials, which is why they are popular for DIY builds from twin-lead, copper pipe or ladder line. The catch is that with no ground plane, the coax shield can carry common-mode current and become part of the radiator. A choke (ferrite beads or a few turns of coax) near the feedpoint often improves pattern consistency, and the SWR may change when you move the cable. The Slim Jim is a folded variant of the J-pole. Its pattern and gain are similar, with a slightly lower radiation angle in many builds.

Collinears. Stacking phased elements squeezes the vertical pattern, trading elevation coverage for horizon gain. That helps for a base station talking across flat terrain. It hurts when you are in hills or in a tall building looking down at a nearby repeater, because the main lobe can pass over the target. Collinear gain figures depend heavily on whether they are quoted in dBi or dBd, a 2.15 dB difference. Check the unit before comparing.

Yagis. A directional antenna adds gain and rejects interference from the sides and rear. Typical 2 m yagis range from about 6 to 12 dBd depending on boom length. The tradeoff is that you have to aim it. For FM repeater work, mount it with the elements vertical. For weak-signal SSB/CW, convention is horizontal polarization. A cross-polarized path can cost many dB, and the actual loss in real terrain varies a lot.

Feedline and connectors. At 440 MHz, coax loss adds up quickly. RG-58 loses several dB per 100 ft on 70 cm, while low-loss types like LMR-400 or RG-213 class cables lose far less. Check the manufacturer's datasheet for the exact cable. A PL-259 is acceptable for 2 m and many mobile installs, but its impedance isn't constant and weatherproofing is poor. An N-type connector has a controlled 50 ohm design, seals better with proper tape or boots, and is the better choice for outdoor UHF runs. Adapters add loss and failure points, so minimize them.

SWR. A low SWR means the antenna's impedance matches the line. It does not prove the antenna is radiating efficiently. A dummy load has a perfect SWR and zero gain. Lossy coax can make a poor antenna look better, because the reflected power is attenuated on its way back to the meter. For a meaningful tuning check, measure at the antenna end if you can, or use a short test cable.

Repeater and satellite use. A repeater site needs omnidirectional vertical coverage, good isolation between transmit and receive antennas or a duplexer, and low-loss hardline. For a user trying to reach a distant repeater, a small yagi can help far more than a taller whip. For low-earth-orbit satellites, a handheld dual-band yagi works for FM passes, and the operator has to track the satellite and account for polarization changes. Fixed station setups often use crossed yagis with circular polarization and an az/el rotator.

Questions to get things started: what are you trying to reach, what is the terrain, and what mounting options do you have? What would you check first when a new install shows high SWR or weak signals?

  • Replies 2
  • Views 18
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

One thing I'd add on mobile installs: the ground plane matters more than whip length. An NMO mount in the center of a metal roof gives the antenna a symmetrical ground plane and a clean pattern. A mount near the edge or on a trunk lip pushes the pattern off to one side and raises the takeoff angle. That is where a 5/8 whip can behave unlike its spec sheet. A quarter-wave is often a decent answer when the ground plane is mediocre.

For mag mounts, the coupling is capacitive through the paint, so the surface must be clean and flat. Any dirt, grit or a thick film can cause SWR changes and scratch the finish. Also watch the cable: the thin coax on most mag mounts has noticeable loss at 70 cm, and routing it through a door seal can crimp it. A permanent NMO with a proper cable through a grommet is usually more reliable than a magnet for daily driving.

  • Administrators

On the J-pole point, the common-mode issue explains a lot of the "it works fine until I touch the coax" complaints. If moving or touching the feedline changes the SWR or the reading, the shield is likely part of the antenna. A choke at the feedpoint and keeping the coax leaving at a right angle away from the antenna usually helps. Because there is no ground plane, mounting height and distance from metal masts also shape the pattern, so a plastic or fiberglass standoff above the mast is worth it.

For the connector question, I'd use N-type for anything exposed to weather and UHF. If you stay with PL-259s, a wrap of self-amalgamating tape plus a layer of vinyl tape keeps water out. Water in coax is a more common cause of slowly rising loss than any single bad antenna. When testing a new setup, compare SWR with a short jumper and with the full run. If the full run looks much better than the short jumper, that points to a lossy cable masking a mismatch.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.