Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Gain staging, dynamic range and noise: what actually limits an SDR, and how to match hardware, software and antenna

ci_cover.jpg

A lot of SDR troubleshooting threads come down to the same few causes: overload, a noisy local environment, or the wrong antenna for the band. This thread is meant to separate them. Please add corrections or other approaches.

Dynamic range is more than ADC bit count. An 8-bit RTL-SDR (RTL2832U with an R820T2 tuner) has a theoretical ADC range of about 48 dB, and real-world usable range is lower. A 12-bit Airspy or LimeSDR and a 14-bit SDRplay RSP give more headroom. The HackRF One has a very wide tuning range and can transmit, but it is also 8-bit, so strong out-of-band signals overload it easily. Wider capture bandwidth also puts more signals into the ADC at once, so a 10 MHz slice of the spectrum can overload a receiver that would be fine with a narrow slice. The front-end filtering and the amount of analogue gain ahead of the converter often matter as much as the ADC.

Recognising overload. Typical signs are images or ghost carriers that appear across the waterfall, a raised noise floor when a strong station is on, and broadcast FM or DAB signals showing up where they should not. A quick test is to lower the RF or LNA gain by a step or two. A real signal drops by roughly the amount you removed, while an intermod product usually drops much faster. If the strong signal is outside your band of interest, filtering is usually better than lowering gain. Broadcast FM notches, MW or HF low-pass filters, and band-pass filters for ham bands all help. Some SDRplay models have built-in notches for broadcast FM and DAB, and the RTL-SDR Blog V3 offers a bias tee but no meaningful front-end selectivity.

Gain staging. Set the tuner gain so that the noise floor rises slightly above the receiver's own noise floor when the antenna is connected, then stop. With an RTL dongle, an AGC setting is not always the best choice, and manual gain with a sensible RF and IF split often gives better results. For SDRplay, the RF gain reduction and IF gain reduction interact with the AGC in SDRuno, so decide whether you want fast AGC for weak-signal work or fixed gain for measuring signal levels. In SDR#, the RTL-SDR source panel offers a tuner AGC and a separate RTL AGC. Using both makes behaviour harder to predict.

Noise, and why it often isn't the dongle. At HF and lower VHF, external noise from switch-mode supplies, LED lighting, power-line hardware and computers usually dominates the receiver's own noise. More gain won't help then, because it amplifies signal and noise equally. What does help is moving the antenna away from the house, adding a common-mode choke on the feedline, and keeping the dongle away from the PC and its USB 3 ports. Long USB cables, ferrites and a powered hub have all been used to reduce USB hash. A noise floor that changes when you unplug or turn off a device is a strong hint that it is a local source.

Antenna matching by band. A telescopic whip is a compromise on every band. For ADS-B at 1090 MHz, a quarter-wave element is about 69 mm. For 137 MHz weather satellites, a V-dipole with each leg of roughly 53 cm is a common starting point. For airband and VHF scanning, a discone gives broad coverage but is not optimal anywhere. For HF reception, active loops and magnetic loops can reduce local noise pickup compared with a long wire, while a long wire with a 9:1 unun is a simple wideband option. If the cable run to a VHF or UHF antenna is long, a low-noise amplifier at the antenna end preserves sensitivity, but it also adds the gain that can cause overload if strong signals are nearby.

HF with a dongle. There are two main routes. Direct sampling on supported RTL-SDR boards (the Blog V3 uses the Q-branch input) lets the converter sample HF directly, but performance is limited by the 8-bit ADC and by the lack of front-end filtering. An upconverter shifts HF to a frequency the tuner covers; with a converter that uses a 125 MHz local oscillator, you set the SDR software's frequency shift to match so that the display shows the real frequency. Dedicated HF receivers such as the Airspy HF+ family or the SDRplay line generally outperform dongles on crowded bands because of their front-end design and dynamic range.

Software choices. SDR# is Windows-focused with a large plugin ecosystem and broad source support. SDRuno is built for SDRplay hardware and handles multiple receivers and detailed spectrum tools. HDSDR uses ExtIO drivers and is popular for HF work and for CAT/OmniRig integration. GQRX runs on Linux and macOS and works with gr-osmosdr or SoapySDR, which also covers LimeSDR. CubicSDR is cross-platform and uses SoapySDR. A good rule is to pick the software that supports your hardware's native driver, since generic wrappers sometimes expose fewer gain controls or less accurate frequency correction.

Digital modes. Most decoders take audio, so a virtual audio cable such as VB-Cable on Windows, or PulseAudio/JACK routing on Linux, connects the SDR's demodulated audio to the decoder. FT8 and other WSJT-X modes need a correctly tuned USB receiver and a system clock synchronised to within about a second. For APRS, Direwolf takes FM audio, rtl_433 reads sensors in the ISM bands directly from the dongle, and multimon-ng handles pagers and some data modes. DSD-style decoders for digital voice depend heavily on a clean signal and correct frequency offset. Frequency error also matters. Many cheap RTL dongles drift with temperature and have a ppm error, so a TCXO-equipped model or a calibrated correction helps with narrowband modes.

Panadapters and bandscopes. A panadapter gives a conventional transceiver a wide spectrum and waterfall display. It usually takes an IF tap or a splitter at the antenna, and CAT control so the display follows the radio's frequency. The most important rule is to protect the SDR from transmit power. Never connect a receiver input to an antenna that your transmitter also uses without a proper relay, attenuator or isolation circuit that has been rated for your power level. The same caution applies to the HackRF and LimeSDR, which have transmit ports.

Questions for discussion: which bands are you trying to cover, what overload symptoms have you seen, and what is your noise floor like at the antenna? Those three details usually decide whether the next purchase should be a filter, an antenna, or a different receiver.

  • Replies 2
  • Views 19
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Administrators

One point worth adding about the spectrum display: FFT size and sample rate change what you see as well as what you hear. A wide span with a small FFT gives coarse resolution, so a weak narrowband signal can be hidden in a bin that also holds a lot of noise. Narrowing the span or increasing the FFT size reduces the resolution bandwidth, and the noise per bin falls, so weak carriers can pop out of the waterfall. Averaging helps too, though it slows the display. That is useful when comparing two antennas, because you want a fair test: the same span, FFT, averaging and gain on each antenna, and ideally a quick A/B switch rather than moving the cable around.

On the overload test, it is worth also checking with a band-pass filter or a notch in place before touching gain. If the spurs vanish with a broadcast FM notch, you have found the cause immediately. That is a more informative test than just turning the gain down, because gain reduction also hides weak wanted signals.

  • Moderators

I would put a bit more weight on the choice between direct sampling and an upconverter. Direct sampling on an RTL dongle is a cheap way to look at HF, but with no preselection the 8-bit converter sees the whole spectrum at once. On a night with strong shortwave broadcast signals, the result can be a crowded display full of images. A converter does not fix that on its own either, because the mixer and any amplifier in it have their own limits. A switchable low-pass or band-pass filter ahead of the converter does more good than most people expect, and it is often cheaper than a new receiver.

On the software side, it is worth checking how each app handles the frequency shift for converters. In SDR# the shift field takes the oscillator frequency, and a mistake with the sign gives a mirrored or offset display. Verify it against a known station, such as a time signal or a broadcast carrier on a known frequency, before trusting the dial. For the panadapter case, I would also add that CAT latency can cause the display to lag when you tune quickly, so the choice of CAT interface and polling rate can affect how usable the setup feels.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.