Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

First homebrew QRP rig: what build order and test gear catch problems before you power it up?

ci_cover.jpg

Many first projects in this hobby, whether a Pixie, a Tuna Tin 2, a BITX-style SSB board or a uBITX kit, are about the same size. The circuit is small enough to understand, but there is enough RF in it to cause trouble: an oscillator that won't start, a final stage that runs hot, a receiver full of hum, or a transmitter with a dirty output.

Here are the questions I'd like to discuss.

1. Is it better to build and test in stages (VFO or crystal oscillator first, then the receive chain, then the PA) or to finish the whole board and troubleshoot afterward? Kit instructions often push toward the second.

2. What is the minimum test gear worth having? A DMM and a 50 ohm dummy load are obvious. What about an RF probe, a frequency counter, a scope, a NanoVNA, or a general coverage receiver used as a monitor?

3. What do builders tend to overlook? Candidates include the low-pass filter after a QRP transmitter, a fused power supply with reverse-polarity protection, and checking an SWR bridge on a known load before trusting it.

Opinions on any of these are welcome. Real-world rule-of-thumb numbers are especially useful.

  • Replies 2
  • Views 17
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Administrators

Staged testing is usually the better habit, even when the kit manual doesn't require it. With a crystal oscillator or Si5351-based VFO, you can confirm frequency, amplitude and stability before anything else is connected. A counter is ideal, but a general coverage receiver tuned to the signal works too, and so does a scope. If the oscillator is wrong, nothing downstream will make sense.

For the transmit side, a current-limited bench supply is very cheap protection. If you don't have one, put a small resistor or a suitably rated fuse in series with the supply for the first power-up. A final transistor drawing far more current than the schematic suggests often means parasitic oscillation, bias trouble or a wrong part value. It is much better to see that on a meter than to smell it.

Always do the first transmit tests into a dummy load, never an antenna. Measure output with an RF probe or a scope across the load, and use P = Vrms²/R to estimate power. For a sine wave, Vrms is the peak voltage divided by 1.414, or the peak-to-peak voltage divided by 2.83. Treat the result as an estimate, since probe and scope error add up at RF.

For BITX-family boards, alignment can be a long process. Calibrating the Si5351 on a uBITX-style rig, checking the BFO or carrier placement against the crystal filter passband, and setting drive levels to the PA all interact. The order you do them in matters, so follow the documentation for your particular board revision.

  • Moderators

On test gear, I'd split it into must-have and nice-to-have. The must-haves are a DMM, a dummy load, an RF probe (which is simple to build) and some way to see your own signal, either a scope or a receiver. A NanoVNA is useful for checking filters, measuring antenna impedance and sweeping crystal filters, though it doesn't replace a scope. If you're comparing the two, a scope shows you waveform problems such as clipping, oscillation and hum, while a VNA shows how a network behaves across frequency.

A direct conversion receiver has its own quirks. There is no image rejection, so you hear both sides of zero beat. Strong AM broadcast stations can get into the audio chain, which is why a bandpass filter ahead of the mixer helps. Hum and microphonics are common, so look at your power supply decoupling, ground routing and any loose toroids or coax. Audio gain stages with an LM386 or similar chip can oscillate if you skimp on bypassing and layout.

A Pixie-style rig is a good learning project, but remember that the single transistor doing double duty as mixer and transmitter finishes with poor receive performance and a transmit signal that needs a proper filter. With any transmitter built around a simple crystal oscillator and final stage, such as the Tuna Tin 2, check the output for harmonics, ideally with a spectrum analyzer or a known-good receiver tuned across the harmonic frequencies. Add a low-pass filter for the band, using the right toroid cores and winding counts from a design you trust. Spurious emission limits depend on your licensing authority, so check the requirements that apply to you.

For SWR bridges, calibrate on a known load: a good dummy load should read close to 1:1, and an open or shorted terminal should give a very high reading. If the bridge disagrees with that, don't trust it with an antenna. Also remember that bridge sensitivity changes with power level, so a QRP-level reading may be less accurate than the same bridge at higher power.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.