Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Dead rig triage: no TX, no RX, or both. What do you check first, and in what order?

ci_cover.jpg

A rig that won't transmit or receive can have a dozen causes, and the order you check them in matters more than any single trick. This is a baseline workflow for discussion. Please poke holes in it or add the steps you'd move around.

1. Power first, and measure it loaded. A bench supply that reads 13.8 V with nothing connected tells you little. Put the meter at the radio's DC input and watch it while the rig transmits. Sag between the supply and the rig points to a bad connector, a corroded fuse holder, thin cable, or a supply that can't deliver the current. Check the fuses on the power lead, and check polarity if anything was recently rewired. If the rig has an internal regulator chain, such as 13.8 V to 8 V to 5 V, measure each rail against the service manual's voltage table.

2. If both TX and RX are dead, think common to both. The shared items are the power rails, the reference oscillator, the PLL/synthesizer, the CPU or control logic, and the antenna changeover relay. An unlocked PLL can kill both directions at once. If you have a scope or frequency counter, confirm the reference oscillator is running and the VCO control voltage is sane. Also rule out the boring stuff: a TX inhibit or lock setting, a stuck mic or PTT line, a squelch or RF gain setting, or a menu reset that changed something.

3. Receive-only faults. Split the path in half. Is there audio noise when you turn up the AF gain with the antenna disconnected? If so, the audio stage is alive and the problem is further up. If the receiver sounds deaf, try injecting a signal from a generator at progressive stages, working from the audio end back toward the antenna. Dirty band-switch contacts, a failed preamp or attenuator relay, and a bad front-end diode or filter can all produce a deaf receiver.

4. Transmit-only faults. Always use a known-good dummy load and a wattmeter, never an antenna, when you diagnose TX. Check for drive from the exciter stages, then the driver, then the final. A rig that shows some power on a low-power setting and none at full power suggests a bias or gain problem rather than a total failure.

5. SWR protection that trips. This is where people chase the antenna when the fault is inside. Put the radio on a dummy load. If the protection still trips or the power folds back, the fault is in the radio: the SWR detector bridge (diodes, trimmers, a cracked toroid), a dirty or failing low-pass filter relay, or a damaged output stage. If it behaves on the dummy load, the problem is outside the rig: the coax, connectors, tuner, or antenna.

6. Noise. First determine whether the noise is entering through the antenna or generated inside. Disconnect the antenna and terminate the input with 50 ohms. If the noise stays, look at the power supply (a switching supply is the usual suspect, so try a battery for comparison), dried-out electrolytic capacitors in the radio's own regulators, and poor internal grounds or shield connections. If the noise goes away, you're chasing an external source or a common-mode problem.

Test gear that earns its bench space: a decent DMM, a current-limited bench supply, a dummy load with a wattmeter, an ESR meter, and a scope with enough bandwidth for the clocks and oscillators you care about. An RF probe for the meter is useful for tracing signal. The service manual is the other essential tool, because the block diagram, test points, and alignment procedure save hours.

So what's your sequence? And do you break it down differently for older discrete-component rigs versus modern SDR-style radios?

  • Replies 2
  • Views 18
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

I'd keep that order and add one rule: don't touch any alignment slugs or trimmers until you know the fault is not a hardware failure. Alignment fixes drift, not dead stages, and tuning a faulty circuit just buries the evidence. If you must adjust something, mark the original position first.

On the voltage table: measure with the radio in the state the table describes (RX, TX, or specific mode), because the readings differ a lot between them. A rail that reads right on receive and collapses on transmit usually points to a load fault or a regulator that can't supply the current.

For capacitors, electrolytics in switching regulators and in the DC-DC sections are common failures in older rigs, and an ESR meter finds them faster than a capacitance meter does. Replace with the same or higher voltage rating and the correct temperature rating, and use low-ESR types in switcher circuits. Check the orientation twice, and clean up any electrolyte residue, since it can eat copper traces. Don't swap RF-path ceramics, mica, or trimmers at random. Use the right dielectric and tolerance for those, or you'll shift the tuning.

For contacts, use a proper contact cleaner on switches, pots, and relay contacts, and go easy on the quantity so you don't float dirt into other areas. A band switch that works on 20 m but is erratic on 15 m is often just a dirty wafer.

  • Moderators

On blown finals, the key question is why they failed. Replacing the transistors without finding the cause usually means replacing them again. The usual causes are high SWR with weak protection, bias runaway, a failed driver stage overdriving the final, a supply over-voltage, or parasitic oscillation. Before applying power to the new devices, check the bias circuit: bias resistors, any bias-regulation transistor, and the thermal-tracking diode if the design has one. Also check the output network, because a shorted or open component there can destroy the new parts quickly.

When you do power up, use a current-limited supply starting at low current, a dummy load, and the service manual's idle-current procedure. If the final stage is push-pull, use matched devices if the manual calls for them. Mount them with fresh thermal compound and make sure the heatsink is flat and clean.

For a scope on this kind of job, check the drive waveform into the final, watch the ALC and protection lines during a short key-down, and look for oscillation when no drive is applied. A final stage that draws current with the drive removed is oscillating or has a bias problem, and you should stop there before it cooks the parts.

On the older versus modern question: with older discrete rigs the service manual's alignment and voltage tables will usually take you most of the way. With newer radios, the firmware, the configuration, and the surface-mount parts make signal tracing harder, so check the settings and the power rails thoroughly before opening the radio up.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.