Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Small lot, 40–10 m: EFHW vs OCFD vs doublet vs vertical, and where does the loss really go?

ci_cover.jpg

Here is a scenario that comes up constantly in small-yard and HOA discussions, so let's work through it. Suppose a lot has room for about 60 ft of wire in a line, two supports around 25 to 30 ft (a tree and the roofline), no tower, and a rule against anything that looks like an antenna. The goal is general-purpose HF coverage on 40 through 10 m, with some DX and some regional ragchewing. The rig is a 100 W transceiver with an internal or external tuner.

The usual candidates are an end-fed half-wave (EFHW) with a 49:1 or 64:1 transformer, an off-center-fed dipole (OCFD), a G5RV-style or plain doublet on ladder line, a trapped dipole, a ground-mounted or elevated-radial vertical, and a small magnetic loop. Each has different tradeoffs in efficiency, pattern, noise pickup and how much common-mode current ends up on the coax.

I would like to compare them on three things that matter more than the SWR meter reading: how much power ends up in the feedline and ground instead of the radiating element, whether the pattern suits the height you can actually reach, and how much common-mode current you will have to deal with in the shack. A flat 1.1:1 SWR on a dummy load tells you nothing about radiation. Where would you start with this lot, and what would you measure first?

  • Replies 2
  • Views 14
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

I would start with height and feedline rather than antenna type. A horizontal wire at 25 to 30 ft is about 0.18 to 0.22 wavelength on 40 m, so it radiates mostly at high angles. That is fine for regional contacts and NVIS-style paths, but it is weaker for DX. On 20 m and up the same wire is a higher fraction of a wavelength and the pattern lowers nicely. Moving a dipole from 20 ft to 35 ft often does more than switching between two wire designs.

The EFHW is attractive here because you need only one feed point, thin wire and a short run of coax. A 40 m half-wave is roughly 65 to 66 ft after end effect. It resonates on 40, 20, 15 and 10 because those are harmonics, but 30, 17 and 12 m are not, so expect to lean on the tuner there. The transformer presents a few thousand ohms at the end of the wire. On a half-wave that end-point impedance is high, so any loss in the transformer, such as core heating or stray capacitance, shows up directly as lost power. The EFHW also has no real counterpoise except the outside of your coax, so a common-mode choke a short distance from the transformer is not optional. It decides whether the coax shield becomes part of the antenna.

A doublet fed with ladder line and a tuner can be more efficient overall because the ladder line is low-loss even at high SWR. A 4:1 current balun or a proper balanced tuner at the shack end keeps the system balanced. Matched-loss figures vary by cable, so check the manufacturer's attenuation tables. RG-58 at 14 MHz loses on the order of 1 dB per 100 ft even when matched, and it gets worse quickly as SWR rises and frequency goes up. Short coax runs are far kinder than long ones.

  • Moderators

I would add that the pattern changes by band, which catches people out. An OCFD with a 4:1 current balun at roughly the one-third point is designed so that the feed-point impedance lands near 200 ohms on several bands. That is why it works on 80, 40, 20 and 10 without a tuner. But the current distribution on the wire is lopsided, so on higher bands you can get lobes pointing in unintended directions. The same goes for a long doublet. Neither is bad, but do not expect a clean cloverleaf on every band.

The G5RV is often misunderstood. It is a 102 ft flat-top with a roughly 31 ft section of ladder line that then transitions to coax. It is a good fit for 20 m, where the section behaves as intended, and on other bands it is basically a tuner-fed multiband doublet with a stub of ladder line in the path. Put a choke where the ladder line meets the coax, or the coax run becomes a radiator that picks up household noise too.

For a stealth vertical, remember that the radials do the heavy lifting. A quarter-wave ground-mounted vertical with only a handful of short radials loses a lot of power to ground resistance. Four resonant radials, raised a few feet and drooped, can be a good compromise: the feed impedance lands in the neighborhood of 50 ohms, and the ground loss is much smaller than with a few short buried wires. A flagpole or a thin wire up a fiberglass pole can disappear against a house or tree line. The HOA question is separate. Read the actual covenants, because federal rules such as PRB-1 apply to state and local government regulation and generally do not override private deed restrictions. A magnetic loop is quiet and compact, but be honest about efficiency. It drops quickly as frequency falls and loop size shrinks, and joint resistance and the capacitor matter more than the shape. It is also very narrow, so you will retune often, and the voltage across the capacitor can be dangerous at higher power.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.