Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Planning an HF shack around the rig: where should the money and effort go first?

ci_cover.jpg

Radio comparisons tend to be IC-7300 vs FT-991A vs Xiegu G90, but the rig is often only part of what decides how a station performs. A 100 W transceiver on a noisy, poorly bonded setup with a marginal antenna system will usually lose to a modest radio on a clean, well-planned one. Here is one way to think about priorities. I'd like to hear where people disagree.

Rig class. The popular options fall into a few groups. The IC-7300 and IC-7610 are direct-sampling SDRs. The 7610 adds a second receiver and a second antenna connector arrangement, which matters for diversity listening and a more flexible station. The FT-991A is a multiband all-mode radio that covers VHF/UHF too, while the FTDX10 is a more HF/6 m-focused design. The TS-590SG and TS-890S are Kenwood's HF/6 m radios, with the 890S being the higher-tier receiver and filtering design. The Elecraft K3S is a superhet with a strong reputation for receiver performance and modularity, and the KX3 is a compact radio for portable use. The Xiegu G90 is a 20 W SDR, popular for portable and budget operation with a built-in tuner. Receiver performance matters most when the band is crowded, as in contests or when a strong station sits next to a weak one. For casual operation, the differences are often smaller than the differences between antenna systems.

Power. A 100 W radio typically draws around 20 A on transmit at 13.8 V, so the supply should have headroom beyond that. Voltage drop in the DC leads is easy to overlook. Short, heavy-gauge cable with a properly rated fuse close to the source avoids the radio shutting down or distorting at the peaks. Switching supplies are small and efficient but can radiate noise into the receiver. If you hear birdies or a raised noise floor, try moving the supply, adding ferrites to the DC and AC leads, or testing with a battery to confirm the source.

Tuners. A tuner presents the radio with a load it likes, but it doesn't make the antenna itself better. If a coax run is long and the SWR at the antenna is high, the feedline loss can be significant even if the radio sees 1:1. Built-in tuners, like the ones in the IC-7300, FT-991A and G90, handle a limited mismatch range. For wide-range or multiband wire antennas, an external tuner, preferably one at the feed point or a balanced-line tuner with a good balun, can be a better match.

Band-pass filters and amplifiers. Band-pass filters become useful when more than one transmitter or receiver shares a site, or when nearby strong signals overload the front end. They have insertion loss and power limits, so they need to be matched to the power level. An amplifier raises other requirements: drive level, ALC and band data cabling, a suitable power supply or mains circuit, cooling, and RF exposure compliance for your location. Adding 500 to 1000 W is not a small step for an existing shack.

Grounding and bonding. This covers three jobs that are often confused. Safety grounding keeps fault current from energizing equipment. Lightning protection gives a surge a controlled path, usually through an entry panel and a bonded ground system, and often by disconnecting antennas when a storm is near. RF grounding is mostly about controlling common-mode current: bond equipment together with short, wide conductors, and use common-mode chokes on the feedline and on USB and audio cables. A long ground wire to a rod is not a reliable RF fix. Local electrical codes apply, so confirm requirements for your location before doing mains-related work.

Given a fixed budget, in what order would you handle the radio, antenna system, power, filtering, grounding, and amplifier? And what is the one item you think new shack builders consistently underspend on?

  • Replies 2
  • Views 13
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

Antenna system first, then the station infrastructure, then the rig upgrade. That ordering holds until the receiver is the limiting factor, which is more often a matter of crowded bands than of the radio being poor. If the noise floor at your location is high from local interference, a better radio won't change that, but a better antenna placement or a receive antenna might.

On tuners, the wording "the tuner makes the SWR 1:1" causes confusion. It makes the radio's output stage happy, but you can still lose power in a lossy feedline, especially at higher bands. If you run a multiband dipole fed with ladder line, the tuner and balun combination matters as much as the antenna. For the amp question, I'd settle the power supply and the mains circuit before you shop, since the amp's requirements can force electrical work. Also check that the radio's ALC and band data connection are compatible with the amp's interface. It's easy to buy the amp first and find out later that the cable doesn't exist.

  • Moderators

I'd put noise management and bonding ahead of buying filters. A lot of problems blamed on the receiver are really common-mode current on the coax shield, a USB cable acting as an antenna, or a switching supply spraying hash. A simple diagnostic: turn off one thing at a time, such as the supply, the computer, or the LED lights, while watching the S-meter or the waterfall on a quiet band. Then add choke or ferrite fixes where the noise originates.

For bonding, one point worth stressing is that the ground rod and the mains safety ground should be tied together, not treated as separate systems. If an antenna entry panel has a different ground potential than the house, a surge can find the path through your equipment. For shack layout, keep RF feedlines, DC leads and audio or USB cables apart where possible, and cross them at right angles rather than running them in parallel. Label everything, because once there are an amp, tuner, and a couple of antennas, troubleshooting without labels gets annoying fast.

Band-pass filters are most valuable in specific cases, like multi-transmitter stations or heavy local interference from a neighbor on another band. Otherwise, a good receiver, proper grounding, and careful antenna placement tend to give a bigger improvement.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.