Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Planning a dual-band mobile install: FTM-500D vs ID-5100A vs TM-D710G, plus wiring, noise and etiquette

ci_cover.jpg

This thread is for working through a 2 meter / 70 centimeter mobile setup from the radio choice through to on-air habits. The three radios that come up most often for this are the Yaesu FTM-500D, the Icom ID-5100A and the Kenwood TM-D710G. They are all FM dual-band mobiles with digital or data features, but they suit different operators.

Radio choice. The FTM-500D is a Yaesu System Fusion (C4FM) radio, so it makes sense if your local repeaters and friends are on Fusion. The ID-5100A is an Icom D-STAR radio with a touchscreen, and its appeal is largely D-STAR plus the dual-receive layout. The TM-D710G is the one people tend to pick for APRS, with a built-in TNC and a long history of use as a mobile packet and tracking station. Before buying, check which digital mode your area actually uses, because a digital mode nobody nearby uses is just an expensive FM radio. Also check the manual for the specific features you need. Not every mobile offers cross-band repeat, and the way each one handles it differs.

Cross-band repeat. The idea is that the mobile receives on one band and retransmits on the other. A common use is a handheld on 70 cm talking through the vehicle's rig and its roof antenna on 2 meters. It is useful at a trailhead, a work site or an event, but it needs some care. Check your local rules on control operator, station identification and any restrictions on this mode. Make sure the transmit and receive frequencies are far enough apart and the antennas separated enough that you are not desensing yourself, and remember a vehicle repeating at 50 W can run warm if you leave it keyed up for long periods. Read the radio's own cross-band instructions, including how to turn it off, so you do not leave it running by mistake.

Mounting. Put the main body where it will not be hit by knees, cargo or airbag deployment, and keep the head unit where you can glance at it without reaching. Many installs use under-seat or console mounting with the control head remote-mounted on radios that support it. Mount the microphone hanger somewhere you can reach it without looking. Whatever you do, do not drill into or fasten to anything you have not checked behind first.

Power and fusing. A 50 W FM mobile can draw on the order of ten amps or more on high power, so do not use a cigarette lighter socket. Run properly sized wire directly from the battery or a suitable fused distribution point, put a fuse on the positive lead close to the source, and use the fuses and gauge the manufacturer specifies. Use a grommet where the cable passes through the firewall so it cannot chafe. Some modern vehicles monitor battery current on the negative terminal, so check the vehicle manual before choosing the ground point. Keep the ground connection short, on clean bare metal, and tight.

Antenna and coax. A roof-center NMO mount with a dual-band antenna is the usual choice. Coax loss climbs on 70 cm, so use a decent low-loss cable rather than the thinnest stuff available, and check SWR on both bands after installing. A poor ground plane or a bad connector can make an antenna look fine on one band and bad on the other.

Noise. Work out whether the noise is on receive or transmit. Alternator whine usually shows up as a tone that follows engine RPM, and it can come through the power lead or into the audio. Ignition and electronic noise tends to be a hash or ticking on receive. Test with accessories off, then switch them on one at a time, since LED lighting, USB chargers and DC-DC converters are common offenders. Keep power wiring away from coax, use ferrites where they help, and make sure the grounds are solid before buying any filters.

Etiquette. Listen before you key up, keep transmissions short, and use a hands-free setup or pull over when traffic needs your attention. Follow your local laws on handheld devices while driving. Do not hog a busy repeater, and if you are on APRS or digital modes, think about what your beacon rate and settings are doing to everyone else on the channel.

What would you prioritise first: the radio, the antenna or the power wiring? And has anyone found a clean way to route the control head and mic cable so the install still looks tidy?

  • Replies 2
  • Views 15
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Administrators

I'd put the antenna and the ground first and the radio second. A well-installed antenna on a roof center with low-loss coax will do more for your range than the extra features on any of those three radios. A good radio on a bad antenna just gives you a nicer screen to look at while nobody hears you.

On the radio choice, I'd base it on what repeaters and nets you actually plan to use. If everything near you is analog FM with a bit of APRS, the TM-D710G is a reasonable fit. If you have a lively D-STAR or Fusion group nearby, buy for that mode. Digital voice only works when other people are on it too.

One wiring tip: when you test, measure the voltage at the radio while transmitting, not just with the engine idling and the radio in receive. A voltage drop under load will tell you whether the wire, a connection or the ground is the weak link.

  • Moderators

On cross-band repeat, treat it as a feature you configure deliberately and test on a quiet frequency before relying on it. Two things cause most of the trouble: the antenna on the vehicle picking up its own transmission, and someone forgetting it is enabled. With a handheld talking into the mobile there is also the question of who is the control operator and how ID is handled, so check your licence rules instead of assuming.

For noise, I'd add one step to the checklist: if the whine is on your transmitted audio but not on receive, look at the microphone cable routing and the power feed to the radio, not the antenna. If the noise is on receive only, go through the vehicle's electronics one by one. A cheap phone charger can be responsible for an alarming amount of hash on VHF.

On etiquette, one thing that gets overlooked is the volume at the speaker. Mobile ops often run the audio loud over road noise, then key up in a quiet parking lot and blast anyone nearby. A small external speaker mounted closer to you helps with that.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.