Rate vs. multipliers: when to leave your run frequency, and how to make SO2R and S&P work for you
- Replies 2
- Views 8
- Created
- Last Reply
Top Posters In This Topic
-
Mod_Dan 1 post
-
Mod_Chrissy 1 post
A better way to browse. Learn more.
A full-screen app on your home screen with push notifications, badges and more.
Most contest scores come down to two numbers: QSO points and multipliers. Where the two compete for your time, you need a rule for when to keep running and when to leave. Here is a framework to pick apart, along with some SO2R, skimmer and fatigue notes.
Run or search and pounce? Running (CQing on a fixed frequency) usually gives the highest sustained rate because the callers come to you. Search and pounce (S&P) gives a lower rate, but it is how you collect multipliers you would never get by sitting on one frequency. The real question is which one is producing more score per hour right now. In a contest with a big multiplier count, such as one with zones and countries, a multiplier can be worth many QSOs by the time you count the final multiplication. In a contest with few or static multipliers, the rate is almost everything.
A practical test is to compare your current 10-minute or 30-minute rate with what you estimate you would make tuning the band. If the run rate has dropped to a trickle of unrelated callers, or you are working only dupes, S&P is probably better. If you are still pulling a steady string of new callers, leaving usually costs you the frequency, and getting it back can be hard.
Rate versus multipliers across the clock. Many operators run hard when the band is wide open to the big population centers, then spend slower periods hunting multipliers. A new multiplier is worth the most early in the contest, when the count is low. Late in the event most of the easy ones are already logged, so S&P yields less per minute and running gets relatively more attractive, unless a band opening is giving you rare stuff.
Band changes. Changing bands costs you your frequency, your rate, and a few minutes of retuning and finding a clear spot. Moving to a new band can pay off when it gives you new multipliers or new propagation, but moving just because the rate dipped for five minutes often loses more than it gains. Watch for the band-opening and band-closing windows for each of your antennas. Contest logging software that displays multipliers by band, and a band map showing what is still needed, helps you decide when a change will pay.
SO2R. Single Operator Two Radio lets you run on one radio while the second radio hunts multipliers during the gaps between callers. The aim is to use dead time, not to split your attention so much that your run rate falls. Some basics:
Isolation matters first. If two radios are on bands that are too close, you can overload the receiver of the one that is listening. Band-pass filters and stubs help, along with antenna separation and a lockout or interlock so you do not transmit on both radios at the same time. Audio also matters: many operators put one radio in each ear and switch the focus between them, and a good SO2R controller or software-controlled audio switching keeps this manageable. N1MM Logger+ supports SO2R operation with its two-radio control and keying options, but your hardware must support the signal routing you configure.
Next is discipline. Pick the best radio to be the run radio, and when a multiplier shows up on the second radio, pounce only when the run radio has just finished a call. If you leave the run radio sitting on an unanswered CQ for several seconds, the cost shows up in the rate meter. Many contesters also find that CW on both radios is easier to manage than mixing modes, but that is a personal preference.
Skimmers and spotting. Packet clusters and skimmer-based spots (for example, the Reverse Beacon Network and local skimmer software) feed the band map with callsigns that are active. They are useful for finding multipliers fast, but spots can contain busted calls, so always copy the call from the other station before you log. If you use spots at all, make sure you are entering the right category, because many contests have separate classes for assisted and unassisted operation. Read the current rules for the specific event, because definitions differ.
Scoring categories. Your category should drive your strategy. Single-band entries reward deep knowledge of one band's openings. All-band entries reward timing the band changes. Low-power and QRP categories change how much you can S&P versus run, because a weak signal makes holding a frequency harder. Assisted versus non-assisted changes how much you rely on the spot network. Check the rules each year, since classes and time limits do change.
Antennas. The best contest antenna is the one that gets the right signal to the right place at the right time. Higher gain and lower takeoff angle matter on the high bands, while on 160 and 80 m a good receive antenna such as a Beverage or other directional receive antenna can matter as much as the transmit antenna. Stacked Yagis give you the ability to switch between high and low takeoff angles. A rotator is great, but if you cannot turn the antenna fast, a fixed multi-direction setup can give better rate for running to a main target area.
Fatigue and endurance. A 48-hour contest is a sleep-management exercise. Plan your off times for when band conditions are weakest, rather than sleeping randomly. Eat and drink on a schedule, and take a short break every couple of hours if you are running hard. Errors rise with fatigue: wrong call, wrong exchange, wrong band. If your logged error rate rises, that is a sign that a rest will improve your score more than another hour of pushing.
For the discussion: what rule of thumb do you use for deciding when to leave a good run frequency to chase multipliers, and how do you set up the second radio so it helps the run radio instead of hurting it?
Link to comment
https://www.hamradiobase.com/forums/topic/11743-rate-vs-multipliers-when-to-leave-your-run-frequency-and-how-to-make-so2r-and-sp-work-for-you/Share on other sites