Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

EME from 2 m to 10 GHz: what each band asks of the station, and how to plan the schedules

ci_cover.jpg

This thread is for comparing notes on what it takes to make Earth-Moon-Earth contacts on the VHF, UHF and microwave bands. Everything below is a rough guide, not a spec. Anyone running a real station should correct me where local experience differs.

The basic problem is path loss. The round trip to the Moon and back is on the order of 250 dB on 144 MHz. It is about 10 dB worse on 432 MHz, about 20 dB worse on 1296 MHz, and roughly 40 dB worse on 10 GHz. The Moon returns only a small fraction of what hits it. The echo takes about 2.5 seconds to come back, and the path loss swings by about 2 dB between perigee and apogee. Every part of the station, from antenna gain to receive noise temperature, is there to claw back some of that.

Here is how I would frame each band.

2 m: This is the most approachable band because antennas are large but manageable. A common starting point is a group of four long-boom Yagis, a legal-limit-class amplifier, and a low-noise preamp mounted at the antenna with proper TX/RX sequencing. Smaller arrays can work the larger stations using JT65 or Q65. Sky noise is a real limit here, so the Moon's position against the galactic background matters.

70 cm: Path loss is higher, but the Yagis are physically smaller, so a bigger array is practical. Faraday rotation is much milder than on 2 m but not always negligible. Libration spreading is also wider than on 2 m.

23 cm: This is the point where many stations move to dishes of a few metres, or to a large array of small Yagis. Feed-line loss and feed efficiency start to dominate. Faraday rotation is not a concern, but libration spreading is.

10 GHz and above: Pointing accuracy, dish surface accuracy, and the sheer cost of low-loss RF plumbing become the main concerns. Doppler shift and spreading are both large, so Q65's wider submodes become useful.

For digital modes, JT65 has been the long-time standard for EME. Q65 is the newer mode in WSJT-X and has submodes designed for different amounts of spreading. Check the current WSJT-X documentation and your local activity group for which submode people actually use on each band.

Questions I would like to hear opinions on:

1. For a first EME station, is it better to start on 2 m with a modest array, or to go straight to 23 cm with a dish?

2. How much does a good moon-tracking and Doppler setup add compared with just a good receiver?

3. What is the most common mistake in scheduling a first sked?

  • Replies 2
  • Views 16
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

On the first question, I would pick the band based on what you can build and maintain, not on theoretical performance. On 2 m, you can add Yagis one at a time and keep improving. A dish for 23 cm has a lower tolerance for error. If the surface, the feed or the pointing is off, there is not much to tune.

Whatever band you pick, receive noise is the first thing to fix. A mast-mounted LNA with a very low noise figure, a relay with sequencing, and short, low-loss feed line matter more than a few extra watts. Even 0.1 dB of loss ahead of the preamp adds noticeable noise. Gain on the antenna side helps both transmit and receive, but the preamp is where cheap improvements usually are.

For tracking, you do need accurate azimuth and elevation, and the beamwidth sets how accurate. A large 2 m array has a beamwidth of a few degrees, so it is forgiving. A 3 m dish on 10 GHz is not. Doppler is the other part. Shifts reach several hundred Hz on 2 m and scale up with frequency, so on microwave bands they are in the kHz or tens of kHz range. WSJT-X has Doppler control and an Echo mode so you can measure your own echo. Use it, because a working echo is the best proof that the whole chain is functioning.

A calculator such as the VK3UM EME planning tool is useful for estimating what the path should allow before buying anything. Treat the output as a budget, not a promise.

  • Moderators

On polarization: there are two separate effects, and people tend to mix them up. Faraday rotation comes from the ionosphere and is strongest on 144 MHz. It becomes less significant on 432 MHz and is basically negligible from 1296 MHz upward. It can make a signal fade in and out over minutes. The other effect is geometric or spatial polarization offset. That depends on where the two stations are relative to each other and to the Moon, and it applies on every band. This is why stations often have a way to rotate their polarization, or to switch between horizontal and vertical, at least on 2 m.

Libration fading is a different thing again. The Moon's apparent motion makes echoes arrive with a spread of Doppler shifts, so the signal flutters rather than fading slowly. The spread grows roughly in proportion to frequency, so it is small on 2 m and much wider at 10 GHz. This is the reason Q65 has multiple submodes and why a mode that works well on 2 m may do worse on microwave.

For skeds, a few practical points:

Agree on the band, mode, submode, start time, and which of you transmits in the first period. Check that you both have the Moon above the horizon for the whole window, not just at the start. Look at the degradation figure for that date, because perigee and apogee differ by about 2 dB and sky noise varies with where the Moon sits. Have a fallback frequency and a way to coordinate, such as a chat page used by EME stations like ON4KST. Finally, allow time for the first few cycles before judging the result. Don't give up because the first few minutes are silent.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.