Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Getting the most out of 5 watts: rigs, antennas and power for portable QRP

ci_cover.jpg

Let's pool practical thinking on low power operation, especially for portable work. By the usual QRP-ARCI convention, QRP means 5 watts output on CW and 10 watts PEP on SSB. Most of the useful discussion is about how to make those watts count, not about the number itself.

The arithmetic is worth keeping in mind. Going from 100 W to 5 W is about 13 dB, which is roughly two S-units on a receiver calibrated at 6 dB per S-unit. Going from 5 W to 10 W is only 3 dB. A better antenna, a quieter site or a more efficient mode will usually beat a bigger amplifier. That is why so many QRPers lean toward CW, which has a narrow bandwidth and a good chance of getting through, and toward simple resonant antennas that get the signal up and out.

The rig choices cover a wide range. The Elecraft KX2 and KX3 are full-featured multimode portable radios with built-in keyers, optional ATUs and SSB, so they suit people who want one box for several modes. The Mountain Topper and the Penntek TR-35 sit at the minimalist CW end, with small size, low weight and low current draw, and they are popular for summit and park activations. Kits like the Pixie sit at the experimental end of the range. A Pixie is a very simple, very low power CW transceiver, and its appeal is the learning and the build. You shouldn't expect it to match a modern receiver for selectivity.

For calling frequencies, the commonly cited CW spots are around 1.810, 3.560, 7.030, 10.106, 14.060, 18.096, 21.060, 24.906 and 28.060 MHz. Commonly cited SSB QRP spots include 3.985, 7.285, 14.285, 21.385 and 28.885 MHz. These are conventions, not guarantees, so check your local band plan and be ready to move if the spot is busy.

Where do you want to put your effort first: the antenna, the power source or the operating technique? For power, LiFePO4 packs are often discussed because their voltage stays fairly flat through the discharge, and a 4-cell pack runs at about 13.2 V nominal. Check that your rig's input range tolerates the fully charged voltage, which can be around 14.4 to 14.6 V. For antennas, the end-fed half wave with a matching transformer and the linked or inverted-V dipole come up most often. What is the lightest field setup you've found that still lets you work stations reliably?

  • Replies 2
  • Views 8
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

On antennas, I'd say a resonant, properly elevated wire is the biggest upgrade available at QRP. An inverted-V dipole fed with coax, with the apex held up by a lightweight mast or a tree, is hard to beat for predictability. It needs no tuner, and the feedline doubles as a way to check SWR. An end-fed half wave is more convenient to deploy because you only need one support, but it's more sensitive to the counterpoise, the feedline routing and the ground conditions. Tuning it, and keeping common-mode current off the coax, takes some attention.

For power, a small LiFePO4 pack is a good match for a rig like the KX2 or KX3 because it holds voltage fairly well while delivering current. Even so, a pack is only useful if the radio is happy at its terminal voltage. Always read the rig's manual for its input range and its reverse-polarity and overvoltage protection, and use a fuse near the battery. A fuse costs very little compared with the radio.

  • Moderators

On rigs, the choice mostly comes down to what you want to do. If you plan to operate CW only and want the lowest possible weight and current draw, the Mountain Topper or TR-35 fit that goal well, because they're built around that single job. The KX2 or KX3 make more sense if you want SSB or digital modes without carrying a second radio, and if you value having a good filter and a full set of controls on the hill. The trade-off is cost and a more complex menu system.

Don't overlook the build-it-yourself route. Kits such as the Pixie are a useful way to learn how a transmitter and receiver work, even if you wouldn't choose one as your main station. If you're interested in building, a simple direct-conversion receiver is a good first project, and QRP-ARCI is a good community to ask about construction and about contest and award activity. On the air, call CQ on or near the QRP spots and listen for replies, since a tight CW signal often does better than expected.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.