Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

48-hour EMCOMM field station: LiFePO4 as primary, inverter generator as backup, and how to keep the noise and grounding sane

ci_cover.jpg

I'm sketching a self-contained field station for a 24 to 48 hour served-agency deployment and would like the plan picked apart before it turns into a packing list. The assumptions: one HF rig at 100 W, one dual-band VHF/UHF mobile, a laptop for digital modes and logging, a small router, and LED lighting in a 10x10 canopy with sidewalls. No commercial power can be assumed.

The power plan is a 100 Ah LiFePO4 battery (roughly 1,280 Wh nominal at 12.8 V) as the primary source, with a small inverter generator as the backup and for recharging, and a folding solar panel to top up during daylight. A rough budget is a few amps on receive for the HF rig, plus the VHF/UHF radio, laptop and lighting, with transmit peaks around 20 A or more for the HF rig at full power. The average draw depends heavily on duty cycle, so I'd rather measure it with a DC watt-hour meter during a practice run than trust the spec sheets.

The distribution plan is a main fuse close to the battery positive terminal, then a fused distribution block with Powerpole-terminated branches, each sized for the load it feeds. The HF rig gets short, heavy leads (12 AWG or larger, depending on length) to keep voltage drop down. LiFePO4 holds its voltage well, but a long thin cable can still make a rig fold back power on transmit peaks.

For antennas, the plan is a telescoping fiberglass mast guyed with non-conductive line, carrying either an inverted-V dipole or an end-fed half-wave on 40/20 m, with a 1:1 current choke at the feedpoint. VHF/UHF would be a separate vertical on a short mast so the HF wire doesn't sit right beside it. The coax run for HF would be RG-8X or similar, since loss on HF is small. The VHF/UHF run would be a lower-loss cable such as LMR-400 or a similar type, because loss there adds up quickly on long runs.

The questions I'd like input on:

First, how do you decide whether the generator is only a backup, or whether it runs on a schedule to recharge the battery? I'm wary of the generator's noise and exhaust near the shelter, and equally wary of finding the battery at 20% at 3 a.m. with no plan.

Second, what do you do about grounding in the field? For safety I'd rely on the generator manual, a GFCI where 120 V is used, and keeping 120 V use minimal. For RF I plan to bond the equipment together and use a short ground connection or radials where the antenna calls for one. I'm not treating a ground rod as lightning protection. My plan is to disconnect and stop operating if lightning is nearby.

Third, what's the best way to find and fix noise sources systematically? Likely suspects are the generator, DC-DC converters, the solar charge controller, LED lights and the laptop power brick. I'd rather have a repeatable test order than start swapping things at random once on site.

  • Replies 2
  • Views 13
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

On the generator question, I'd lean toward treating it as a planned recharge tool rather than a pure emergency backup. A schedule gives the net more predictability. For example, you can decide in advance that a battery at a given state of charge, or a certain time window, triggers a recharge during a lull in traffic. Whatever the trigger, that decision should sit with the station lead and be written in the plan, not made on the fly.

Placement matters as much as schedule. Put the generator well away from the tent and downwind, and don't rely on open sidewalls to keep carbon monoxide out. A battery-powered CO alarm inside the shelter is cheap insurance. Also check how you're charging the LiFePO4 from the generator: a proper charger or DC-DC source with the right charge profile (LiFePO4 is commonly charged at around 14.2 to 14.6 V, but follow your battery's documentation). Charging from a generic AC-DC adapter can add noise and may not suit the battery.

On noise, a repeatable order is: start with everything off and note the receive noise floor on the band you care about, with the HF rig on battery alone. Then add one item at a time, always in the same order, and note the change on the S-meter or in a waterfall display. Solar charge controllers and cheap DC-DC converters are frequent offenders, so test them early. Common fixes are ferrite chokes on the DC leads (clamp-on works for testing), more separation, or swapping to a different charger. Keep a short log of what was noisy and what fixed it, which makes the next setup faster.

  • Administrators

A few notes on the antenna and coax side. Common-mode current on the coax shield is probably the largest hidden noise and RF-in-the-shack problem in setups like this, so a choke at the feedpoint is a good start. If the station still picks up noise, adding a second choke where the coax enters the shelter often helps. Keep the coax and the DC leads from running in parallel for long stretches where you can avoid it, and cross them at right angles when you have to.

Keep the mast clear of power lines with a generous margin. The usual rule of thumb is that the fallen mast shouldn't be able to reach a line, with extra room added on top. Set the guy anchors at a reasonable distance from the base, and mark the lines with flagging tape so people don't walk into them in the dark. A mast that's easy to lower quickly is worth more than the last few feet of height, especially if wind or weather picks up.

For the checklist, I'd split it into three: setup, operation, and teardown. Setup should be ordered so the safety items come first (site hazards, generator placement, overhead lines, CO alarm), then power, then antennas, then radios. Teardown should run in reverse. Include a final step to walk the site for stakes, cable ties and flagging. For EMCOMM specifically, add a quick comms check with the net control station before the tent is fully set up, so a feedline or choke problem shows up while the mast is still easy to reach.

And since you're planning a practice run, do a full-duration test on the battery with the gear in its real configuration, even if it's only a couple of hours. Measured watt-hours per hour of operation will tell you far more than any estimate.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.