ⓘ Callsign lookups are in real time via the FCC database.
Vanity callsign availability is refreshed daily at 6:00 AM CST.
The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cmvia PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHzDXSpotterInfo
Recent spots—
Select a band above to load spots
Ready — select a band to fetch live spots
Planning an HF shack around a 100 W rig: amp, tuner, PSU, filters, and grounding/bonding
I'd like to compare notes on how people structure an HF station once it grows past "rig, power supply, wire." The rigs people usually discuss are the IC-7300 and IC-7610, FT-991A and FTDX10, TS-590SG and TS-890S, K3S, and the smaller KX3 and Xiegu G90. They all end up facing the same system-level questions, whatever the architecture.
1. Rig choice affects the rest of the chain. The IC-7300 is a single-receiver direct-sampling SDR. The IC-7610 adds a second receiver path and separate antenna handling, which matters for two-radio operation or diversity-style listening. The FT-991A is an all-mode HF/VHF/UHF rig. The FTDX10 and the Kenwood and Elecraft rigs are more HF-focused, and the K3S and TS-890S emphasize roofing filter selection and strong-signal behavior. The KX3 and G90 are lower-power and portable, so the main limits are output power, cooling at high duty cycle, and how you handle an ATU or external amp. Check the manual for each rig's rated power, duty-cycle limits, and amplifier interface, because those differ.
2. Power supply. A 100 W class rig on 13.8 V typically draws around 20 A or more on SSB peaks, so a 25-30 A supply gives some headroom. Voltage sag under load can cause low output, distortion, or resets. Use appropriately heavy, fused DC leads, keep them short, and make sure the fuse is rated for the cable, not only the radio. Switching supplies can radiate noise on HF, so check the noise floor with the supply on and off, and try ferrites or a different supply location if you see birdies. Also check the rig's maximum supply voltage tolerance before using any adjustable supply.
3. Amplifier and ALC. The usual mistake is overdriving the amp. Set the rig's drive so the amplifier reaches its rated output with no ALC activity. Excess ALC distorts the signal and splatters on adjacent frequencies. Use the amp's band-data or keying line if the rig supports it, and confirm that the amp's PTT/relay line voltage and current are within the rig's keying-output limits. Many modern rigs have a specific amplifier or relay port with limited current, so an interface may be needed.
4. Tuner placement. An internal ATU in the rig can match the rig to the amp input only if the amp presents a reasonable load. At high power, the external tuner after the amp is normally what matches the amp output to the feedline and antenna. The tuner must be rated for the power and the mismatch it will handle. A tuner cannot fix a poor antenna system, and with a high-SWR feedline you lose power in the coax. For that reason, tuning at the antenna, or using low-loss line, makes a real difference.
5. Band-pass filters. For a single operator on a single rig, a BPF is often unnecessary. They are important when two transmitters can be on at once, such as multi-op or SO2R, or when a nearby station's transmit energy overloads your front end. They also help if the receiver overloads from a strong out-of-band signal such as AM broadcast. Make sure the filter is rated for transmit power and has low insertion loss on the band you use. For harmonics, a low-pass filter is the relevant component, and many amps include one.
6. Shack layout. Keep RF and AC cabling separate where practical, and cross at right angles when they must meet. Put the amp and tuner where the coax runs are short. Route USB and CAT cables away from the amp and antenna feed. Label coax and power runs. A switchbox or an entry panel with surge protection and a shared bond point makes later changes much easier.
7. Grounding and bonding. There are three jobs here: electrical safety, lightning protection, and RF performance. They overlap but are not the same. Equipment chassis should connect to a common bonding bus, and that bus should connect to the service ground per local electrical code. A ground rod alone is not a good RF ground, and a separate rod without bonding to the electrical system is a safety risk. Bring all feedlines in at one entry point and bond the shields there. Common-mode chokes at the feedpoint and where the coax enters the shack often reduce RFI and hum. If you see RF in the audio, USB dropouts, or a hot microphone, start by checking for common-mode current on coax, power, and USB cables.
I'm interested in how others structure this. Do you put the tuner before or after the amp, how do you separate noise sources, and what grounding scheme works for you in a typical house?
I'd like to compare notes on how people structure an HF station once it grows past "rig, power supply, wire." The rigs people usually discuss are the IC-7300 and IC-7610, FT-991A and FTDX10, TS-590SG and TS-890S, K3S, and the smaller KX3 and Xiegu G90. They all end up facing the same system-level questions, whatever the architecture.
1. Rig choice affects the rest of the chain. The IC-7300 is a single-receiver direct-sampling SDR. The IC-7610 adds a second receiver path and separate antenna handling, which matters for two-radio operation or diversity-style listening. The FT-991A is an all-mode HF/VHF/UHF rig. The FTDX10 and the Kenwood and Elecraft rigs are more HF-focused, and the K3S and TS-890S emphasize roofing filter selection and strong-signal behavior. The KX3 and G90 are lower-power and portable, so the main limits are output power, cooling at high duty cycle, and how you handle an ATU or external amp. Check the manual for each rig's rated power, duty-cycle limits, and amplifier interface, because those differ.
2. Power supply. A 100 W class rig on 13.8 V typically draws around 20 A or more on SSB peaks, so a 25-30 A supply gives some headroom. Voltage sag under load can cause low output, distortion, or resets. Use appropriately heavy, fused DC leads, keep them short, and make sure the fuse is rated for the cable, not only the radio. Switching supplies can radiate noise on HF, so check the noise floor with the supply on and off, and try ferrites or a different supply location if you see birdies. Also check the rig's maximum supply voltage tolerance before using any adjustable supply.
3. Amplifier and ALC. The usual mistake is overdriving the amp. Set the rig's drive so the amplifier reaches its rated output with no ALC activity. Excess ALC distorts the signal and splatters on adjacent frequencies. Use the amp's band-data or keying line if the rig supports it, and confirm that the amp's PTT/relay line voltage and current are within the rig's keying-output limits. Many modern rigs have a specific amplifier or relay port with limited current, so an interface may be needed.
4. Tuner placement. An internal ATU in the rig can match the rig to the amp input only if the amp presents a reasonable load. At high power, the external tuner after the amp is normally what matches the amp output to the feedline and antenna. The tuner must be rated for the power and the mismatch it will handle. A tuner cannot fix a poor antenna system, and with a high-SWR feedline you lose power in the coax. For that reason, tuning at the antenna, or using low-loss line, makes a real difference.
5. Band-pass filters. For a single operator on a single rig, a BPF is often unnecessary. They are important when two transmitters can be on at once, such as multi-op or SO2R, or when a nearby station's transmit energy overloads your front end. They also help if the receiver overloads from a strong out-of-band signal such as AM broadcast. Make sure the filter is rated for transmit power and has low insertion loss on the band you use. For harmonics, a low-pass filter is the relevant component, and many amps include one.
6. Shack layout. Keep RF and AC cabling separate where practical, and cross at right angles when they must meet. Put the amp and tuner where the coax runs are short. Route USB and CAT cables away from the amp and antenna feed. Label coax and power runs. A switchbox or an entry panel with surge protection and a shared bond point makes later changes much easier.
7. Grounding and bonding. There are three jobs here: electrical safety, lightning protection, and RF performance. They overlap but are not the same. Equipment chassis should connect to a common bonding bus, and that bus should connect to the service ground per local electrical code. A ground rod alone is not a good RF ground, and a separate rod without bonding to the electrical system is a safety risk. Bring all feedlines in at one entry point and bond the shields there. Common-mode chokes at the feedpoint and where the coax enters the shack often reduce RFI and hum. If you see RF in the audio, USB dropouts, or a hot microphone, start by checking for common-mode current on coax, power, and USB cables.
I'm interested in how others structure this. Do you put the tuner before or after the amp, how do you separate noise sources, and what grounding scheme works for you in a typical house?
Link to comment
https://www.hamradiobase.com/forums/topic/11764-planning-an-hf-shack-around-a-100-w-rig-amp-tuner-psu-filters-and-groundingbonding/Share on other sites