Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Radio mods worth doing, and the ones that cause trouble: a practical order of operations

ci_cover.jpg

I'd like to sort radio modifications into three groups: mods that usually pay off, mods that need care, and mods where legality matters more than the technical result. Here is a rough starting list for discussion.

Start with the least invasive changes. Firmware updates from the manufacturer, a better speaker or headset, a clean power source, a feedline choke and better cooling fix most real-world complaints without opening the case. Before flashing anything, back up your memories and any calibration or alignment data, and use a stable power source. A flash that is interrupted by a brownout is a common way to brick a radio.

Noise is often the biggest performance problem, and it is often not in the radio at all. Switching supplies, USB chargers, LED lighting, solar charge controllers and cheap power injectors can all raise the receive noise floor. A battery-powered AM or shortwave receiver is a quick way to find the source. Common-mode current on the coax is the other usual culprit, so a choke at the feedpoint and another near the shack entry is cheap insurance. Compare any change by reading the S-meter or noise floor before and after, not by ear.

On the receive side, an expanded-receive unlock on a handheld or mobile is easy to do through a menu or programming software such as CHIRP, but the front end is still what it was. Wideband receivers pick up broadcast FM, pagers and nearby transmitters through intermod and images. A bandpass filter, a broadcast FM notch or a better antenna helps more than widening the tuning range. Some jurisdictions also restrict what you may intentionally monitor or repeat, so check your local rules.

A TCXO is worth it mainly where frequency error is large compared with the signal. One ppm is about 144 Hz at 144 MHz, 432 Hz at 432 MHz and 10 kHz at 10 GHz. That matters for narrowband weak-signal work, microwave and some digital modes. It matters much less for 25 kHz FM. If you swap one in, match the frequency and output type (clipped sine or CMOS) to what the circuit expects, then recalibrate against a trusted reference such as WWV or a GPS-disciplined source.

Fans and heat management matter most for digital modes. FT8 transmits for roughly 12.6 seconds of every 15, which is close to continuous carrier. A 100 W rig can be stressed at full power, so many operators run well below rated output. If you add a fan, make sure the airflow reaches the heatsink, filter its power lead, and keep it away from receive antenna leads, because PWM fan controllers can generate noise.

Then there is the legal side. In the US, MARS and CAP operation is authorized by the program, not by the radio mod. An out-of-band transmit unlock does not make operating on those frequencies legal. Both programs have their own equipment and authorization policies, so check with your program's communications officer before changing a radio. A modified amateur rig also should not be used on services that require certified equipment, such as GMRS, marine, aviation or public safety. Even on amateur bands you are responsible for spurious emissions, which is why third-party firmware and cheap handhelds with weak harmonic filtering deserve scrutiny.

Which of these mods do you think are overrated? Are there any you would never do on a rig you rely on for emergency communications?

  • Replies 2
  • Views 13
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

Good list. I'd move audio higher on it, because a lot of 'my signal sounds bad' reports come from level problems rather than hardware. On FM, over-deviation from too much mic gain causes splatter and distortion, and an EQ or compressor can't fix it. On SSB and digital modes, the usual mistake is overdriving the audio input. If the ALC is moving on a digital mode, you're already distorting. Set the drive so the ALC barely registers and control output power with the rig's power setting.

For receive audio, a small external speaker with some DSP filtering often does more than any internal mod, especially in a noisy mobile. Cutting low-frequency rumble and trimming high-frequency hiss improves intelligibility without touching the radio's insides.

I'd also add that power upgrades are mostly wiring: heavy gauge cable, a fuse close to the battery, solid Powerpole connections, and checking the voltage at the radio during transmit rather than at the supply. Voltage sag under load can cause more trouble than the radio itself.

  • Administrators

On battery upgrades for handhelds, I'd stress staying with packs that keep their protection circuitry. Lithium-ion cells with no protection board are a real fire risk. Higher capacity is fine, but if a charger or pack mod bypasses charge control, the gain in runtime isn't worth it. USB-C charging mods are popular, but make sure the charging circuit is built for the pack's voltage. A 2S pack is normally charged to about 8.4 V, which is not what a basic USB 5 V input provides directly.

For mobile and base use, the rig's rated input is usually about 13.8 V with some tolerance, but check the manual. LiFePO4 packs often work well, but confirm that the charging voltage and the radio's maximum input are compatible, and check the radio's low-voltage cutoff behavior.

On the legal point, I'd stress that an unlock is not the same as authorization. 'The radio can do it' and 'I'm allowed to do it' are different questions. If you do a transmit mod, keep a copy of the original settings, document what you changed, and keep a stock-configured radio available if your club, agency or served organization has equipment requirements.

Where do you land on third-party firmware for cheap handhelds? The added features are tempting, but I'd want a spectrum analyzer check of the harmonics and spurs before treating one as a fully compliant transmitter.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.