Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Repeater basics that trip people up: offsets, CTCSS vs DCS, time-outs, and what "linked" really means

ci_cover.jpg

Many "I can hear the repeater but can't get into it" questions come down to four settings: the offset direction, the access tone, the tone mode in the radio, and whether the repeater is open to you at all. This thread is for collecting practical notes, starting with analog FM and moving on to linking and digital repeaters.

The offset is the gap between the repeater's output (the frequency you listen on) and its input (the frequency you transmit on). Directories list the output frequency. In the US, common conventions are 600 kHz on 2 meters and 5 MHz on 70 cm, with the direction (plus or minus) depending on which part of the band the pair sits in. Other countries and regions use different spacings, so check your local band plan instead of assuming. A repeater listing may also give two tones. One is the input tone (CTCSS, often called PL, a Motorola trademark) that you must transmit to open the machine. The other is the output tone, which the repeater may send so your receiver can decode it. Some repeaters use DCS instead, which is a digital code rather than a sub-audible tone. Radios label these settings differently: "Tone" often means encode only, while "TSQL" or "Tone Squelch" means encode and require the tone to hear audio.

Some questions to get going:

1. What is your first troubleshooting step when you can hear a repeater but it won't respond? One idea is to use the radio's reverse function to listen on the input frequency, which tells you whether you are within simplex range of other users.

2. How do you tell whether a repeater is linked to another system before you transmit, and how does that change how you talk?

3. How much should you trust directory entries, and what do you check before you rely on one?

  • Replies 2
  • Views 13
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

On the first question, the order I'd suggest is offset direction, then tone, then tone mode. If the radio shows the right output frequency and you can hear traffic, confirm the offset is going the right way. Then check that the tone you are sending matches the repeater's input tone. A very common mistake is entering the output tone as the input tone, or the reverse. Also check whether the radio is set to encode only or to encode and decode. If it is set to decode, it may mute the repeater audio when the repeater isn't sending that tone. That can look like a dead repeater.

One caution about tone squelch on your receiver. It mutes signals that don't carry the matching tone, and that includes a co-channel signal that is interfering with your reception. It also isn't security. CTCSS and DCS only control who opens a receiver, and anyone can hear or transmit the tones. Treat the tone as an access setting, not as privacy.

For etiquette, listen before you transmit, because the repeater may be in use, running a net, or carrying a conversation you can't hear from the input side. Identify as your local rules require. In the US that means at intervals and at the end of communication, but check the rules where you operate. Keep transmissions short and leave a gap after each one so others can break in. The time-out timer (TOT) on most repeaters, often somewhere around one to three minutes though the owner sets it, will drop the repeater if you hold the key too long. Let the courtesy tone finish before you key up again. Some repeaters use it to signal that the timer has reset, and it gives a breaker room to speak. Avoid kerchunking (keying briefly just to test), and give your callsign if you're checking signal strength.

  • Moderators

For the linking question, the most dependable way to know is the owner's documentation or the repeater club's page. Repeaters may connect to other repeaters through EchoLink, AllStar, IRLP, Wires-X, or a reflector, either all the time or only for scheduled nets. Many repeaters announce a connection or disconnection with a voice message. If you hear one, expect a delay and expect people on the other end to be hearing you. Pause longer than usual between transmissions and say your callsign clearly, since the remote listeners may not know your area.

Each system works a bit differently. EchoLink is VoIP and uses node numbers. IRLP and AllStar are also commonly controlled with DTMF commands, and AllStar nodes are based on Asterisk software. Wires-X belongs to Yaesu's System Fusion and uses "rooms" that nodes connect to. Whether a particular repeater is still part of one of these networks can change, so check with the repeater's owner or club. Treat DTMF control codes as the owner's property. Don't connect or disconnect nodes or reflectors unless the repeater's rules say users may.

DMR and D-STAR are different because the radio must support the mode, and the radio needs more programming than an FM repeater does. DMR commonly needs the right frequency pair, color code, time slot, talkgroup and your DMR ID. D-STAR involves callsign routing fields, such as the your-call and repeater fields, plus the module letter and gateway. A mistyped talkgroup, time slot or color code gives you the digital equivalent of the wrong CTCSS tone. On a busy talkgroup, listen for a while before you key up, because your audio can land in a conversation the repeater is carrying for many people.

As for directories, RepeaterBook and club lists are useful starting points, but entries can be out of date. Look for a recent update date, and check the club's own page for tones, linking schedules and rules. In many places a regional frequency coordinator assigns repeater pairs to reduce interference. In the US, coordinated repeaters are generally given priority when disputes arise. An open repeater accepts general use, though the owner still sets the rules. A closed or restricted repeater limits access to members or approved users, often via a tone or other control, so ask the owner before you assume you can use it.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.