Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Planning a 5 W portable QRP kit: rig choice, antenna, LiFePO4 power, and where to call CQ

ci_cover.jpg

I'm putting together a plan for a lightweight portable QRP station and want to compare approaches before spending money. The target is 5 W CW as the main mode, with the option of SSB when conditions allow. Typical use would be a park, a summit, or a backyard picnic table, using 40, 30, 20 and maybe 15 m.

The rigs I keep comparing fall into three groups:

Multiband general-coverage rigs: the Elecraft KX2 and KX3. These cover CW, SSB and digital modes, have built-in keyers and optional ATUs, and can run on internal or external batteries. They cost the most, but they are the most flexible if you want SSB.

Minimalist CW rigs: the Mountain Topper series and the Penntek TR-35. They are small and light and sip current on receive. The tradeoff is that you work CW only, and the TR-35 is limited to a single band per unit.

Kit and learning projects: Hendricks-style QRP kits and Pixie-type transceivers. A Pixie is a very simple, very low-power design. It is great for learning how a transceiver works, but it is not a good first choice if you need to make contacts reliably.

Questions for the group:

  • For a single-person pack, is the extra capability of a KX2 or KX3 worth it compared with a CW-only rig?
  • What antenna would you pair with each? I'm considering an end-fed half-wave (EFHW) with a 49:1 transformer, or a linked dipole on a fiberglass pole.
  • Is a small LiFePO4 pack a good choice, and what should I check about voltage before connecting it to a rig?
  • Which QRP calling frequencies should I use, and how does QRP-ARCI fit in?
  • Replies 2
  • Views 10
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

Start with the mode, because it decides most of the rest. If you only plan to work CW, a Mountain Topper or TR-35 gives you the best weight and current drain per contact. If SSB matters even occasionally, the KX2 or KX3 make more sense, since a CW-only rig can't do it at all. Note that a Pixie-style rig is closer to a build-and-learn project than a practical field radio. Its receive selectivity is very wide and its output is low, so it is best used as a bench project or for experiments on a quiet band.

On power, 5 W versus 100 W is a 13 dB difference. At roughly 6 dB per S-unit, that is a bit over two S-units at the receiving end. So a QRP signal is not hopeless. It just needs a decent antenna and a good choice of band and time. The antenna is where most of your effort pays off. Height, a clean feedpoint and low-loss coax matter more than squeezing a little more power out of the rig.

On calling frequencies, these are the commonly used QRP spots. Check the band plan for your region, because they can differ:

  • CW: about 1.843, 3.560, 7.030, 10.106, 14.060, 18.096, 21.060, 24.906 and 28.060 MHz. On 40 m, 7.040 is also used in some regions.
  • SSB: about 3.985, 7.285, 14.285, 21.385 and 28.885 MHz.

These are meeting points, not reserved frequencies. If someone is already there, move up or down a few kHz. Many QRP-ARCI contests count 5 W CW and 10 W PEP SSB as QRP output, but read the current rules for any event before you operate, since the exact categories change.

  • Moderators

On power: LiFePO4 is a good fit for portable work because the voltage stays fairly flat through most of the discharge. A 4-cell (4S) pack has a nominal voltage of about 12.8 V, and a fully charged pack sits around 13.3 to 13.6 V at rest. That is fine for most 12 V QRP gear, but always check the maximum input voltage in the manual for your specific rig. Also check that the pack has a BMS or is protected, and use a charger meant for LiFePO4 chemistry. A fuse near the battery is cheap insurance, and so are a proper power connector and a small voltmeter. A 3S LiPo works too, but its voltage sags more under load, and on SSB peaks that can show up as lower output.

For the antenna, the two options you mentioned are both good, but they behave differently:

  • End-fed half-wave with a 49:1 transformer: quick to deploy, easy to hang from a tree branch, and good for multiband operation on harmonically related bands. The weak point is common-mode current on the coax, so add a choke near the feedpoint and expect some variation with height and surroundings.
  • Linked dipole: a bit more setup, but it is balanced, predictable, and easy to tune to a band by opening or closing links. It usually gives a cleaner SWR and fewer surprises.

A lightweight kit would be a roll of thin wire, a small pole or a throw line for a branch, a few feet of coax with a choke, and a small tuner if the rig has no internal ATU. Before leaving home, test the setup in the yard on at least one band so you know where it needs adjustment.

If I had to pick one starting point, I'd go with a KX2 or a Mountain Topper depending on whether you want SSB, plus a linked dipole or EFHW and a small LiFePO4 pack. You can expand from there once you know which bands you actually use.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.