Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

VHF/UHF antenna choices: J-pole vs. collinear vs. 5/8 wave vs. yagi, and what coax, connectors and SWR actually tell you

ci_cover.jpg

Antenna threads on VHF/UHF often turn into "which one has the most gain," but the better question is where you need the energy to go. A vehicle, a home base station, a repeater site and a satellite pass all reward different designs. Here is a framework to argue with.

Gain is pattern shaping, not free power. Gain figures are only meaningful with a reference. dBd is relative to a half-wave dipole and dBi is relative to an isotropic radiator, with dBi = dBd + 2.15. A vertical omni has no horizontal directivity, so its gain comes from squashing the pattern flatter toward the horizon. A longer collinear or 5/8-wave stack sends more energy at low angles and less up and down. That helps with distant stations on flat terrain. It can hurt when you are close to a repeater on a hill, or in a valley with steep angles to the signal, because you may be sitting in a shallow null of your own pattern.

Quarter-wave whip. At 2 m a quarter wave is roughly 19 to 20 inches, and at 70 cm it is about 6.5 inches. It is simple, mechanically tough and has a low-angle pattern. It needs a decent ground plane, which on a vehicle means the roof. It is near 50 ohms with no matching network, so there is little to go wrong. Gain is about unity over a quarter-wave reference, so you give up a little for ruggedness and easy fitting.

5/8 wave. At 2 m this is around 48 to 50 inches, with a loading coil or matching network at the base. Typical claims are about 3 dB over a quarter-wave, and the pattern is lower and flatter. The catch is that the matching network and ground plane matter a lot. A 5/8 on a small or poorly grounded surface can show a decent SWR yet radiate with a tilted, distorted pattern. Where the ground plane is small, such as a trunk lip or a small mag mount on a thin roof, the shorter antenna is often the less fussy one.

J-pole and Slim Jim. Both are end-fed half-wave antennas with a quarter-wave matching section. The J-pole has the familiar J shape. The Slim Jim is a folded variant with a lower radiation angle and a bit more apparent gain. They need no radials, which is why people like them for attic, balcony or temporary use. But "no radials" does not mean the feedline stays out of the system. Without a choke, common-mode current can flow on the outside of the coax and shift the pattern and the SWR reading. A few turns of coax into a coil, or ferrite beads, at the feedpoint helps. These are also often built from twin-lead or copper pipe, which makes them cheap but dependent on a careful build for the matching dimensions.

Collinears. These stack phased half-wave sections to flatten the pattern and build omni gain. Claimed gain of 6 to 9 dBi is common on commercial designs, but the actual figure depends on length, quality of the phasing sections and feedpoint matching. They want to be mounted away from the mast, ideally at the top, or on a side arm that holds them several feet clear of metal. Too close, and the mast becomes part of the antenna.

Yagis. A yagi trades coverage for directivity. More elements on a longer boom narrow the beamwidth, raise forward gain and improve front-to-back ratio. This suits point-to-point work, a distant repeater, weak-signal SSB/CW and some satellite use. The cost is a rotator or manual pointing, plus a more sensitive installation. Weak-signal work is usually horizontally polarized, while FM repeaters and simplex are vertical, so check which one you actually need. Cross-polarized, you can lose 20 dB or so, although real-world reflections reduce that loss.

Mobile mounting: NMO vs. mag mount. NMO uses a 3/4 inch hole in the roof and gives the best electrical and mechanical connection, and the whips are interchangeable. A mag mount needs no drilling, but the coupling relies on the paint and magnet contact, the cable must run through a door or window gasket without being pinched, and a cheap one can slide or scratch at speed. Roof center is the best position for a symmetrical pattern. A mount at the edge of the vehicle gives a lopsided pattern, with the body shadowing one side.

Coax and connectors. Loss increases with frequency and length. Very roughly, RG-58 loses about 4 to 5 dB per 100 ft at 150 MHz and nearly double that at 450 MHz. RG-213 or LMR-400-type cable is much better, around 1.5 to 2 dB per 100 ft at 2 m and a bit under 4 dB at 70 cm, depending on the cable. A 6 dB gain collinear plus 5 dB of loss on a long thin cable is a poor trade. PL-259/SO-239 (UHF connectors) are fine on 2 m for moderate power, but they are not constant impedance and are not as good on 70 cm and above. N-type connectors are constant impedance, better sealed and a sensible choice for permanent outdoor use. All outdoor connections should be weatherproofed with proper tape or sealing, and the coax should have a drip loop so water does not run into the connector.

SWR. Low SWR means the transmitter sees a good match. It does not mean the antenna is radiating well. A dummy load has an excellent SWR and radiates nothing. Lossy coax can also hide a bad antenna, since reflected power is attenuated on its way back. Whenever possible, check the antenna with a short jumper or an analyzer at the feedpoint, and sweep the whole band, not just one frequency.

Repeater and satellite specifics. A repeater antenna system must cope with transmit/receive separation, duplexers, isolation and a pattern sized for the coverage area, which is why you see omnis with controlled downtilt. Satellite antennas have different problems. LEO satellites move quickly and their orientation changes, so circular polarization (crossed yagis, turnstiles, helicals) reduces fading, although hand-held directional yagis with linear polarization are often used on FM satellites with manual polarization rotation. You also need the right balance of gain and beamwidth, because a very narrow beam is hard to keep pointed at a satellite crossing the sky.

What are you trying to cover: local repeaters, simplex, a long path, satellites or all of the above? And is the antenna going on a car, a roof or a mast? That decides most of the choice.

  • Replies 2
  • Views 12
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

One point I'd add to the pattern discussion is that mounting location often matters more than the label on the antenna. A theoretically better 5/8 on a poor ground plane or next to a metal mast can be worse than a plain quarter-wave in the clear. For a base station, get the antenna above nearby metal and away from the mast, use a side arm if needed, and keep the feedline dropping away at right angles to the antenna as far as practical. For a mobile install, centered on the roof is the best target, and I'd treat any bumper, trunk or fender location as a compromise that skews the pattern.

On connectors, I agree with N-type for permanent outdoor runs. If you do use PL-259s, solder them carefully, check for shorts with a meter before connecting, and use the right reducer for RG-58 and similar thin cable. Many connector problems come from a poor solder joint or a damaged braid, not the connector design. Water getting into the cable through a poorly sealed connector is a common failure and can slowly turn a good coax into a lossy one.

  • Moderators

On SWR, it helps to remember that the reading depends on the entire path, not only the antenna. If you measure at the radio end with a long run of thin coax, the loss in both directions pulls the measured SWR down toward 1:1, so a damaged antenna can look better than it is. If the reading seems too good for a cheap antenna, test it at the antenna end or with a known-good short jumper. An analyzer sweep tells you more than a single-frequency check, since it shows where the resonance is and how wide the usable band is.

For satellites, I'd keep it simple at first. For FM birds, a small hand-held yagi on 2 m and 70 cm is workable, and you can rotate it to cope with polarization changes. If you want a fixed setup, a crossed-yagi pair with circular polarization is more convenient, but you need elevation and azimuth control, correct phasing, and low-loss cable on the 70 cm side. The 70 cm path is usually where cable loss hurts most, so that is a good place to spend on better coax. Also, because the satellite moves, Doppler shift is a real factor: you'll be retuning during the pass, especially on UHF, rather than parking on one frequency.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.