Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Getting real performance out of an SDR: dynamic range, noise floor and where the dongle ends and the antenna begins

ci_cover.jpg

A lot of SDR questions come down to the same thing. People compare ADC bit depth and sample rate, then find the real limits are overload, a noisy shack, or an antenna that doesn't suit the band. This thread is meant to separate those factors. Add corrections if I get something wrong.

Start with dynamic range, because the marketing numbers can mislead. An RTL-SDR dongle has an 8-bit ADC, and the usable range is further limited by the tuner's gain stages. A strong FM broadcast signal can overload the front end and produce phantom signals across the band. Those images and intermod products are not weak signals you could dig out with better software. The overload happens before the data reaches the PC. Lowering gain, adding an FM broadcast notch filter, or using a bandpass filter ahead of the dongle all work in the analog domain, where the problem occurs. Receivers like the SDRplay RSP series, the Airspy HF+ and the Airspy R2 have more ADC resolution and better front-end design. Even so, 14 bits does not make a receiver immune to a strong local transmitter. Filters, attenuation and AGC settings still matter.

Gain is where many setups go wrong. Maximum gain makes the waterfall look busy and lively, but it often just raises the noise floor and pushes the ADC toward clipping. A better method is to tune to a quiet part of the band, then raise gain until the noise floor in your software rises noticeably. Back off a little from there. Check again at the busiest time of day, because overload often shows up when strong broadcast stations are at their best. If the noise floor rises sharply when you connect the antenna, the antenna or its environment is the limit. If it doesn't, the receiver's own noise is the limit, and a low-noise amplifier close to the antenna might help on higher bands.

HF needs separate treatment. The RTL-SDR v3 has a direct sampling mode that lets it receive HF without an upconverter. It is simple and cheap, but it is a compromise: the ADC samples the signal with little front-end filtering, so strong shortwave broadcasters can swamp weak amateur signals. The traditional alternative is an upconverter, which shifts HF up into the tuner's range. The software must then be told the converter's LO offset or the frequency display will be wrong. A converter adds its own mixer, oscillator and spurs, so you need to know whether a signal is real or a product of the converter. Dedicated HF receivers like the Airspy HF+ family or SDRplay models that cover HF directly avoid some of this, at higher cost.

On the software side, the main choices are these. SDR# is popular on Windows and has a large plugin ecosystem. SDRuno is the native software for SDRplay hardware. HDSDR is an older Windows program that uses ExtIO drivers and handles CAT control and panadapter-style setups well. GQRX is the common choice on Linux and macOS, built on GNU Radio and gr-osmosdr. CubicSDR is cross-platform and uses SoapySDR, which makes it handy for LimeSDR and HackRF. The HackRF One and LimeSDR are more flexible platforms, with wide tuning ranges, transmit capability and very wide bandwidth. They are not automatically better receivers for a narrow weak signal. HackRF's 8-bit ADC makes it prone to overload, and the LimeSDR needs careful gain staging.

For digital modes, the usual chain is SDR software demodulating audio, a virtual audio cable passing that audio to a decoder, and sometimes a CAT or rig-control link for frequency tracking. WSJT-X, fldigi, multimon-ng, dsd-based tools and ADS-B decoders all work this way or take IQ data directly. Decoding problems usually come from the signal, not the decoder. Check for wrong sideband, wrong filter bandwidth, audio levels that are too hot, and a sample clock or frequency offset that has drifted. Cheap dongles can have a frequency error of a few parts per million, which matters for narrow modes. Check the ppm setting against a known reference signal.

Antennas matter more than most upgrades. A discone or wideband whip is convenient for scanning but compromises sensitivity everywhere. A resonant dipole, a properly sited loop or a purpose-built antenna for the band will usually beat a wideband one. On HF, local noise from switch-mode supplies, LED lighting and USB 3 devices often swamps the receiver's own noise. A ferrite choke on the feedline, a good distance from the PC, and a clean power source can help more than a better dongle. An active loop or a small magnetic loop can also reduce received noise compared with a short whip near the house.

Panadapters and bandscopes are the last category. A panadapter feeds the radio's IF to an SDR so you can see the spectrum around the frequency you're tuned to. That is useful, but the SDR sees what the radio's roofing filter and IF stage let through, so the picture is not the whole band. A bandscope built into a transceiver is more tightly integrated but usually has less flexibility than PC software.

Questions for the thread. How do you decide when gain is set correctly? What filters make the biggest difference to a low-cost receiver? And is there a case for direct sampling over an upconverter on a budget?

  • Replies 2
  • Views 13
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

One tip on gain: use a spectrum view with a stable noise reference, not the waterfall colours. Waterfall palettes and range settings hide the changes you need to see. With the antenna connected, find a spot with no signal, then change the gain and watch what the noise floor does. If the floor climbs about as much as the gain, the system is noise-limited by the antenna or the environment, and you gain little from more amplification. If the floor barely moves at the lowest gain settings, the receiver's own noise dominates and a bit more gain or an LNA is justified. Overload shows differently. Signals appear in places they shouldn't, they change with gain in an uneven way, or a strong carrier produces copies at regular spacings. A simple test is to add a few dB of attenuation. A real signal drops by that amount, while an intermod product usually drops faster.

On the FM notch, a broadcast-band notch filter can make a visible difference on an RTL-SDR for HF, VHF air band and similar uses, but it does nothing for overload from strong signals inside the band you want. In that case a bandpass filter for the band is the better tool.

  • Moderators

On direct sampling versus an upconverter, it depends on the target. For listening to broadcast stations and strong signals, direct sampling on an RTL-SDR v3 is often good enough. The limits are the 8-bit ADC and the lack of selective filtering, so it struggles when strong stations sit next to the weak signal you want. An upconverter changes the signal path and lets the tuner's own gain control work, but you accept the converter's spurs and the need to set the offset correctly. If you go that way, check the display against a known station before trusting any frequency readout.

If the aim is serious HF listening, receivers designed for HF are a more direct fix than working around an RTL-SDR. They have better dynamic range and sensible input filtering, which matters most when the antenna is a long wire exposed to strong signals. For VHF and UHF work, an RTL-SDR with a bandpass filter and LNA at the antenna remains a good low-cost setup. A HackRF or LimeSDR makes more sense when you need transmit, wide bandwidth or experimentation, not when you only need a better receiver.

For digital decoding, also check the sample rate and CPU load. Dropped samples at high sample rates can mimic a weak signal, and the decoder gets blamed for something the USB link caused.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.