ⓘ Callsign lookups are in real time via the FCC database.
Vanity callsign availability is refreshed daily at 6:00 AM CST.
The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cmvia PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHzDXSpotterInfo
Recent spots—
Select a band above to load spots
Ready — select a band to fetch live spots
Dead or sick rig: a sensible order of attack for no TX, no RX, protection faults and noise
Most repair threads jump straight to "which transistor is bad?" Usually it is faster to narrow the fault with a fixed order of checks first. This is one workable sequence for a rig that is dead, deaf, won't transmit, or keeps dropping into protection. Corrections and additions are welcome, because different designs and eras fail in different ways.
1. Power first, and measure it under load. A supply that reads 13.8 V with nothing connected can sag badly once the rig draws current. Check the fuse, the inline fuse holder, the DC connector and the reverse-polarity protection. Then measure voltage at the rig's input terminals while it is transmitting or drawing receive current. Compare that to the reading at the supply terminals. A difference of more than a few tenths of a volt points to a poor connector, a thin cable or a corroded fuse clip. Inside the rig, check the regulated rails (5 V, 8 V, 9 V and so on) against the service manual. A rail that is low or noisy often comes down to a failing electrolytic or a regulator that is running hot.
2. Split the problem: common path, RX only, or TX only. If the rig has no receive and no transmit, suspect something common to both. Candidates are the antenna relay or PIN-diode switching, the PLL or reference oscillator, the CPU and its supply, or a main power rail. If only one mode is dead, follow that signal chain. For receive, work from the antenna jack through the front end, mixers, IF filters and detector to the audio amplifier. For transmit, work from the microphone or CW keying through the modulator, driver and final to the low-pass filter and output.
3. Protection faults are often a symptom, not the disease. High-SWR foldback can come from a bad antenna, a damaged coax or a failed connector. It can also come from a faulty SWR detector bridge in the rig, or a drifted reference voltage on the protection circuit. Put the rig into a known-good dummy load. If the fault vanishes, the problem is outside the rig. If it persists, check the forward and reflected detector diodes, the bridge balance and the voltage the protection circuit sees. Also look at what the radio does on different bands, since a filter or relay fault on one band can look like an SWR problem.
4. Blown finals: find out why before replacing them. Final transistors rarely fail for no reason. Typical causes are high SWR, excessive supply voltage, loss of bias or incorrect bias, a failed driver stage, parasitic oscillation, poor heatsinking, or a failed bias-temperature compensation device. Check the driver and bias circuit, and any emitter or gate resistors, before fitting new devices. Use a current-limited bench supply or a series lamp for the first power-up, and set idle current exactly as the manual specifies. Use the correct replacement part and mounting method, with fresh thermal compound.
5. Capacitors and contacts. Old electrolytics dry out, leak and lose capacitance, and the leaked electrolyte can corrode traces under surface-mount parts. When replacing, match capacitance and voltage rating, observe polarity, and use low-ESR types where the circuit needs them, as in switching supplies and regulators. Do not replace everything blindly. Look for bulging, brown residue and discoloured boards, and measure the suspects. For dirty switches, potentiometers and connectors, use a cleaner that is rated safe for the plastics involved, and don't flood the part with lubricant. Intermittent noise when a control is turned usually means a dirty or worn pot. Noise that varies when the chassis is tapped suggests a cracked solder joint or poor board contact.
6. Alignment last, not first. Realigning a rig that has a component fault just hides the problem and makes things worse. Once the fault is repaired, follow the service manual procedure. That normally needs a signal generator, frequency counter, RF power meter, dummy load and often a scope. Reference oscillator calibration, IF and discriminator adjustments and transmit power calibration all have a specified order. Mark or photograph slug and trimmer positions before touching them.
Test gear that earns its place: a decent DMM for DC voltages, resistance and diode checks; a scope for seeing oscillator drive, audio, ripple and distortion; an RF probe or power meter; and a dummy load. Fit a 10x probe to the scope, keep ground leads short, and be careful about grounding a scope across a hot-chassis or tube-era circuit. Discharge large capacitors and respect high voltage in valve equipment.
What symptom-to-cause shortcuts do you use? I'm particularly interested in how people tell a real final-amplifier fault from a bad protection circuit.
Most repair threads jump straight to "which transistor is bad?" Usually it is faster to narrow the fault with a fixed order of checks first. This is one workable sequence for a rig that is dead, deaf, won't transmit, or keeps dropping into protection. Corrections and additions are welcome, because different designs and eras fail in different ways.
1. Power first, and measure it under load. A supply that reads 13.8 V with nothing connected can sag badly once the rig draws current. Check the fuse, the inline fuse holder, the DC connector and the reverse-polarity protection. Then measure voltage at the rig's input terminals while it is transmitting or drawing receive current. Compare that to the reading at the supply terminals. A difference of more than a few tenths of a volt points to a poor connector, a thin cable or a corroded fuse clip. Inside the rig, check the regulated rails (5 V, 8 V, 9 V and so on) against the service manual. A rail that is low or noisy often comes down to a failing electrolytic or a regulator that is running hot.
2. Split the problem: common path, RX only, or TX only. If the rig has no receive and no transmit, suspect something common to both. Candidates are the antenna relay or PIN-diode switching, the PLL or reference oscillator, the CPU and its supply, or a main power rail. If only one mode is dead, follow that signal chain. For receive, work from the antenna jack through the front end, mixers, IF filters and detector to the audio amplifier. For transmit, work from the microphone or CW keying through the modulator, driver and final to the low-pass filter and output.
3. Protection faults are often a symptom, not the disease. High-SWR foldback can come from a bad antenna, a damaged coax or a failed connector. It can also come from a faulty SWR detector bridge in the rig, or a drifted reference voltage on the protection circuit. Put the rig into a known-good dummy load. If the fault vanishes, the problem is outside the rig. If it persists, check the forward and reflected detector diodes, the bridge balance and the voltage the protection circuit sees. Also look at what the radio does on different bands, since a filter or relay fault on one band can look like an SWR problem.
4. Blown finals: find out why before replacing them. Final transistors rarely fail for no reason. Typical causes are high SWR, excessive supply voltage, loss of bias or incorrect bias, a failed driver stage, parasitic oscillation, poor heatsinking, or a failed bias-temperature compensation device. Check the driver and bias circuit, and any emitter or gate resistors, before fitting new devices. Use a current-limited bench supply or a series lamp for the first power-up, and set idle current exactly as the manual specifies. Use the correct replacement part and mounting method, with fresh thermal compound.
5. Capacitors and contacts. Old electrolytics dry out, leak and lose capacitance, and the leaked electrolyte can corrode traces under surface-mount parts. When replacing, match capacitance and voltage rating, observe polarity, and use low-ESR types where the circuit needs them, as in switching supplies and regulators. Do not replace everything blindly. Look for bulging, brown residue and discoloured boards, and measure the suspects. For dirty switches, potentiometers and connectors, use a cleaner that is rated safe for the plastics involved, and don't flood the part with lubricant. Intermittent noise when a control is turned usually means a dirty or worn pot. Noise that varies when the chassis is tapped suggests a cracked solder joint or poor board contact.
6. Alignment last, not first. Realigning a rig that has a component fault just hides the problem and makes things worse. Once the fault is repaired, follow the service manual procedure. That normally needs a signal generator, frequency counter, RF power meter, dummy load and often a scope. Reference oscillator calibration, IF and discriminator adjustments and transmit power calibration all have a specified order. Mark or photograph slug and trimmer positions before touching them.
Test gear that earns its place: a decent DMM for DC voltages, resistance and diode checks; a scope for seeing oscillator drive, audio, ripple and distortion; an RF probe or power meter; and a dummy load. Fit a 10x probe to the scope, keep ground leads short, and be careful about grounding a scope across a hot-chassis or tube-era circuit. Discharge large capacitors and respect high voltage in valve equipment.
What symptom-to-cause shortcuts do you use? I'm particularly interested in how people tell a real final-amplifier fault from a bad protection circuit.
Link to comment
https://www.hamradiobase.com/forums/topic/11810-dead-or-sick-rig-a-sensible-order-of-attack-for-no-tx-no-rx-protection-faults-and-noise/Share on other sites