Getting started with LEO satellites: FM birds vs. linear transponders, Doppler handling, and which antenna setup to build first
- Replies 2
- Views 12
- Created
- Last Reply
A better way to browse. Learn more.
A full-screen app on your home screen with push notifications, badges and more.
This thread is meant as a working discussion for anyone moving from "I can hear a bird" to "I can reliably make contacts." Satellite operating splits into a few distinct skill sets, and it helps to separate them instead of trying to learn everything at once.
1. FM satellites (AO-91, AO-92, SO-50 and similar)
These work like a single-channel repeater in the sky. Only one station at a time can use the transponder, and the passes are short, often 5 to 10 minutes. Most use a 70 cm uplink and a 2 m downlink, though some are the other way around, and some need a CTCSS access tone to open the repeater. SO-50 is known for requiring an arming tone, for example. Frequencies, tones and operational status change over time, and satellites sometimes go silent or run in a reduced mode. Check a current source such as the AMSAT status pages before you plan around any specific bird.
Because the repeater is half-duplex from your point of view, you want to hear your own downlink while you transmit. That means either a radio that can receive and transmit at the same time on different bands, or two radios. Wear headphones, or you will get audio feedback from your own speaker.
2. The ISS
The ISS can carry an APRS digipeater and a crossband voice repeater, but neither is guaranteed to be on at any given time. When the voice repeater is active it behaves much like an FM bird. APRS is a packet mode: your TNC or software must be set up for the right path and frequency, and your station will appear in the digipeated stream only if the packet is copied. Check the ARISS or AMSAT announcements for the current configuration.
3. Doppler shift
Doppler is just relative velocity divided by the speed of light, multiplied by the frequency. For a LEO satellite on 435 MHz you can expect a swing of roughly +/-10 kHz across a pass. On 145 MHz it is about a third of that, around +/-3 to 4 kHz. On FM that matters because the receiver bandwidth is narrow. The usual technique is to correct the receive side in steps and keep the transmit frequency close to nominal, or to track both sides carefully if you can. At the start of a pass the satellite is approaching, so the received frequency is high. At the end it is receding and the received frequency is low.
For linear transponders such as RS-44, Doppler matters even more, because you are also trying to keep your signal inside a passband of tens of kHz. RS-44 is an inverting linear transponder: as you tune your uplink up, the downlink moves down. Most operators tune the downlink to where they want to hear the contact and adjust the uplink to compensate.
4. Software tracking
Gpredict (cross-platform) and SatPC32 (Windows) both predict passes and can drive the radio's frequency and the rotator. Both depend on up-to-date Keplerian elements (TLEs) and an accurate computer clock, so update keps regularly, especially for newly launched or maneuvering satellites. Gpredict can use Hamlib's rigctld for CAT control. SatPC32 uses its own interface, with some radio support built in. Whichever you choose, test the Doppler behavior on a strong pass before you rely on it.
5. Antennas
A handheld Yagi like an Arrow-style dual-band antenna is the classic start. It is cheap, portable, and good enough for FM birds if you can point it by hand. A few things to keep in mind:
6. Grid squares
For most satellite contacts the exchange is call signs and a 4-character Maidenhead grid locator. Know yours before the pass starts. Rover and portable operation from grid corners is popular because it gives other stations a new grid.
7. QO-100
QO-100 (Es'hail-2) is different in kind: it is in geostationary orbit, so there is no Doppler tracking and no pass to chase. It uses 2.4 GHz uplink and 10 GHz downlink, with a narrowband (SSB/CW and digital) transponder and a wideband one. It needs a dish and microwave gear rather than a hand-held Yagi, and you must be within its footprint. A good habit on any linear transponder: never be louder in the downlink than the beacon, because one strong signal can compress the whole passband.
Questions to get discussion going: What are people using for pointing on a first FM setup? When does it make sense to move from an Arrow to a fixed Yagi and rotator? And how do you handle Doppler on SSB: software rig control, or by ear with a VFO?
Link to comment
https://www.hamradiobase.com/forums/topic/11814-getting-started-with-leo-satellites-fm-birds-vs-linear-transponders-doppler-handling-and-which-antenna-setup-to-build-first/Share on other sites