Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

From-scratch 40/20 m wire antenna: wire, feedpoint, choke, and checking it with a model and an analyzer

ci_cover.jpg

I'm putting together a build plan for a first homebrew HF wire antenna and would like people to poke holes in it before any wire gets cut. The goal is a 40 m dipole that also works on 20 m. The supports are a tree at one end and a roughly 10 m (33 ft) fiberglass telescoping pole at the other, so it will probably end up as a slight inverted-V or sloper rather than a flat-top. I'm trying to decide between a fan dipole, a trap dipole, and a single dipole fed with ladder line and a tuner.

Here is the plan so far.

Wire: 14 AWG stranded copper-clad steel for the radiating element. It is strong and doesn't stretch much, which matters over a 20 m span. Soft-drawn solid copper tends to creep and sag. Insulated wire is easier to handle, but the dielectric lowers the resonant length by a few percent, so it needs more trimming than bare wire.

Length: the usual starting formula for a half-wave dipole is about 468 / f(MHz) feet, which gives roughly 66 ft overall for the low end of 40 m. That is only a starting point. Height above ground, nearby objects, wire diameter, and the inverted-V angle all shift the real resonance, so the plan is to cut long and trim.

Insulators and rope: UV-stabilized plastic or acrylic end and center insulators, with polyester (Dacron-type) line to the supports. Nylon stretches and cotton rots.

Center support: a solid center insulator with a strain-relief hole, so the coax weight pulls on the plate and not on the soldered joint. The coax end should be sealed with self-amalgamating tape or similar, because water can wick into the braid.

Feed and choke: coax with a common-mode choke at the feedpoint, either a stack of ferrite cores or a coil of the coax itself. A dipole is a balanced antenna on an unbalanced line, so without a choke the shield carries current and becomes part of the radiator.

Questions for the group. Is a coax choke good enough, or should I use a purpose-built 1:1 current balun? For 20 m, is it better to rely on the 40 m dipole's third-harmonic-ish behavior, or build a proper fan element? And what's the most useful order for modeling and measuring, so I don't chase a number that doesn't mean anything?

  • Replies 2
  • Views 11
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

On the feedline question, think about what each option is solving. A 40 m dipole used on 20 m is a full-wavelength-long wire, and it presents a very different impedance, often a few thousand ohms at the feedpoint depending on length and height. Real 40 m dipoles don't land exactly on a 3x harmonic either. Coax can feed that, but the SWR will be high and the tuner has to cope with it. Open-wire or window ladder line handles this much better, because its loss stays low even at high SWR. The trade-off is that ladder line wants a balanced tuner or a tuner plus a 4:1 current balun. It also needs to be kept away from gutters, metal masts, and other conductors, and it should hang off the antenna symmetrically with as few twists as possible.

For a choke on coax, the key number is common-mode impedance at the frequencies you use, not how many turns it has. A coil of coax gives a modest impedance that is band-dependent, and it can work well for one band and badly for another. Several ferrite cores (type 31 is the usual choice for lower HF, type 43 higher) threaded onto the coax give a broader, more predictable result. If you want to check it, use an analyzer to measure the impedance across the choke while it is disconnected from the antenna. A larger real-part impedance is better. Don't judge it by the SWR.

If the ladder-line approach gets the nod, a single dipole fed with ladder line would also cover 80 and 15 m. At that point a fan dipole or traps are not needed, though you pay for it with a tuner and a more careful feedline routing plan.

On traps, they let one wire cover several bands, but each trap adds loss, narrows bandwidth, and has to be weatherproofed. A fan dipole avoids the loss. Its drawback is that the elements interact, so you tune the shorter one first, then the longer one, then recheck.

  • Moderators

For the order of operations, I'd model first, then build, then measure at the feedpoint. In EZNEC, define the wire with the right diameter and material, set the ground to something realistic (not perfect ground), and put the antenna at the planned height. Pay attention to segmentation. Too few segments on a wire is a common cause of nonsense results. Before trusting the numbers, run the average-gain test. A value near 0 dB suggests the model geometry and segmentation are well-behaved, while a large deviation means something is wrong in the model.

MMANA-GAL is a good second opinion. It is free and based on MININEC, and it is handy for quick comparisons and for optimizing dimensions. Its ground handling is different from NEC-based tools, so I wouldn't treat absolute numbers as gospel when the antenna is low over real ground. If two different modeling engines agree on the trend (say, resonance moves down by X kHz per inch added), that is more trustworthy than either absolute value.

Neither program knows about the tree, the house, the roof gutters, or the wet soil, so the model won't predict resonance to the kilohertz. Use it to understand the sensitivities: how much the inverted-V angle changes the feedpoint impedance, what 10 percent shorter ends do, how a 3 m height change shifts the pattern.

When measuring, use an antenna analyzer or a NanoVNA, calibrated at the end of the cable you use. Measure at the feedpoint if you can. If you measure through a length of coax, loss makes the SWR look better than it really is and the reactance reading is rotated by the cable. Resonance is where the reactance X crosses zero, and that isn't always the SWR minimum, especially when the feedpoint resistance isn't 50 ohms. Sweep the whole band in steps and note R and X, not just SWR. Then trim in small amounts, one end at a time, and keep the ends symmetric.

If you later build a vertical, the same method applies. A quarter-wave is about 234 / f(MHz) feet, and the ground system is the part that decides efficiency. Several elevated resonant radials usually beat a few short ones lying on the ground. A ground-mounted base needs many more radials. An elevated, drooping-radial design is a natural fit with your fiberglass pole.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.