ⓘ Callsign lookups are in real time via the FCC database.
Vanity callsign availability is refreshed daily at 6:00 AM CST.
The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cmvia PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHzDXSpotterInfo
Recent spots—
Select a band above to load spots
Ready — select a band to fetch live spots
Planning an HF shack around a 100 W rig: power, grounding, tuners, filters and amp interfacing
This thread is for comparing notes on building an HF base station that works well and stays safe, whatever the radio. The 100 W class is crowded: IC-7300 and IC-7610, FT-991A and FTDX10, TS-590SG and TS-890S, and K3S. The QRP and portable-leaning radios (KX3, Xiegu G90) often end up as base rigs too. They differ in receiver architecture, but most shack problems come from the same areas: the supply, RF in the shack, the interface to an amplifier, and a feedline or tuner that is blamed for something else.
Start with the receiver. Direct-sampling radios like the IC-7300 and IC-7610 digitize the signal at the antenna, so they depend heavily on the preselector filters and ADC headroom. The IC-7610 adds two receivers and dual antenna handling. The TS-890S and K3S lean on roofing filters and a traditional superhet design, which tends to behave differently when a strong neighbor is on the next band. None of this makes one radio right for everyone. It does mean a nearby station, a broadcast signal or your own second transmitter can show up as different symptoms on different radios. Before adding gear, switch the preamp and attenuator on and off and see how the noise floor and the strong signals respond. If the band noise barely changes with the preamp, you are probably limited by external noise rather than receiver sensitivity.
On power, a 13.8 V supply for a 100 W rig needs to deliver the full transmit current without sagging. Many 100 W radios draw roughly 20 A or a bit more at full output, so check the manual for your specific model. A 25 to 30 A supply is a sensible size if the radio is the only load, with extra margin if you also run a transceiver, tuner or accessories from the same source. Use heavy-gauge, short DC leads, fuse the positive lead close to the source, and check voltage at the radio during transmit rather than at the supply terminals. Switching supplies can radiate noise on HF, so if you hear birdies or a raised noise floor that changes when you unplug the supply, try a different supply, ferrites on the DC and output leads, or a linear supply.
Grounding and bonding are easy to mix up, so separate the three jobs. Safety grounding keeps equipment cases from becoming energized in a fault. Lightning protection gives surge energy a low-impedance path outside the building. RF grounding is what people usually mean when they say they need a better ground for the radio, and it is the least predictable. A long wire to a rod does not make a good RF ground on HF, and it can carry RF back into the shack. A common approach is a single-point entry panel where coax and control lines are protected, bonded to the building's service grounding system as required by your local electrical code. Then keep the in-shack bonding short and tidy. Where the code and your jurisdiction apply, follow them, and have an electrician involved for mains work.
For RF in the shack, the usual fixes are common-mode chokes on the coax at the feedpoint and where it enters the shack, a balanced antenna fed properly, and separating the audio, USB, CAT and power cables from the coax. If you see RF burning the lip on a microphone, the radio resetting on a particular band, or USB audio dropouts while transmitting, treat it as common-mode current first. An ATU or an extra ground rarely cures it.
Tuners deserve some clarity. An internal ATU in the IC-7300, FT-991A, TS-590SG or G90 and the matching networks in the KX3 and K3S are designed to present a safe load to the final stage within their range. They do not make a high-SWR antenna efficient, because loss in the feedline still happens. A remote tuner at the feedpoint is a different case, since it keeps the coax running at lower SWR and can reduce loss on long runs. If an antenna needs the tuner to cover a wide range, consider whether the antenna itself is the wrong choice before buying a bigger tuner.
Band-pass filters are mostly for stations with more than one transmitter on the same site, like multi-op contesting or SO2R, or for strong out-of-band interference. They do not fix a bad antenna or noise from your own equipment. If you do use them, be careful with SWR and power rating, and plan the filter switching so you never transmit into the wrong band.
Finally, amplifier interfacing is where QRP and 100 W radios part ways. A G90 puts out about 20 W and many amplifiers need more drive than that, while a KX3 is limited to a few watts for best linearity on some bands. For a 100 W radio, set drive so the amp reaches its rated output without flat-topping, and check ALC levels. Use the radio's amplifier keying output and verify its voltage and current limits against the amp. Most modern rigs use an open-collector or relay-style keying output with limits that should be in the manual. A poorly planned PTT line can cook a transistor in the radio.
What would you check first when building or upgrading a shack, and what are you tackling right now: noise, RF in the shack, amp interfacing, or the layout itself?
This thread is for comparing notes on building an HF base station that works well and stays safe, whatever the radio. The 100 W class is crowded: IC-7300 and IC-7610, FT-991A and FTDX10, TS-590SG and TS-890S, and K3S. The QRP and portable-leaning radios (KX3, Xiegu G90) often end up as base rigs too. They differ in receiver architecture, but most shack problems come from the same areas: the supply, RF in the shack, the interface to an amplifier, and a feedline or tuner that is blamed for something else.
Start with the receiver. Direct-sampling radios like the IC-7300 and IC-7610 digitize the signal at the antenna, so they depend heavily on the preselector filters and ADC headroom. The IC-7610 adds two receivers and dual antenna handling. The TS-890S and K3S lean on roofing filters and a traditional superhet design, which tends to behave differently when a strong neighbor is on the next band. None of this makes one radio right for everyone. It does mean a nearby station, a broadcast signal or your own second transmitter can show up as different symptoms on different radios. Before adding gear, switch the preamp and attenuator on and off and see how the noise floor and the strong signals respond. If the band noise barely changes with the preamp, you are probably limited by external noise rather than receiver sensitivity.
On power, a 13.8 V supply for a 100 W rig needs to deliver the full transmit current without sagging. Many 100 W radios draw roughly 20 A or a bit more at full output, so check the manual for your specific model. A 25 to 30 A supply is a sensible size if the radio is the only load, with extra margin if you also run a transceiver, tuner or accessories from the same source. Use heavy-gauge, short DC leads, fuse the positive lead close to the source, and check voltage at the radio during transmit rather than at the supply terminals. Switching supplies can radiate noise on HF, so if you hear birdies or a raised noise floor that changes when you unplug the supply, try a different supply, ferrites on the DC and output leads, or a linear supply.
Grounding and bonding are easy to mix up, so separate the three jobs. Safety grounding keeps equipment cases from becoming energized in a fault. Lightning protection gives surge energy a low-impedance path outside the building. RF grounding is what people usually mean when they say they need a better ground for the radio, and it is the least predictable. A long wire to a rod does not make a good RF ground on HF, and it can carry RF back into the shack. A common approach is a single-point entry panel where coax and control lines are protected, bonded to the building's service grounding system as required by your local electrical code. Then keep the in-shack bonding short and tidy. Where the code and your jurisdiction apply, follow them, and have an electrician involved for mains work.
For RF in the shack, the usual fixes are common-mode chokes on the coax at the feedpoint and where it enters the shack, a balanced antenna fed properly, and separating the audio, USB, CAT and power cables from the coax. If you see RF burning the lip on a microphone, the radio resetting on a particular band, or USB audio dropouts while transmitting, treat it as common-mode current first. An ATU or an extra ground rarely cures it.
Tuners deserve some clarity. An internal ATU in the IC-7300, FT-991A, TS-590SG or G90 and the matching networks in the KX3 and K3S are designed to present a safe load to the final stage within their range. They do not make a high-SWR antenna efficient, because loss in the feedline still happens. A remote tuner at the feedpoint is a different case, since it keeps the coax running at lower SWR and can reduce loss on long runs. If an antenna needs the tuner to cover a wide range, consider whether the antenna itself is the wrong choice before buying a bigger tuner.
Band-pass filters are mostly for stations with more than one transmitter on the same site, like multi-op contesting or SO2R, or for strong out-of-band interference. They do not fix a bad antenna or noise from your own equipment. If you do use them, be careful with SWR and power rating, and plan the filter switching so you never transmit into the wrong band.
Finally, amplifier interfacing is where QRP and 100 W radios part ways. A G90 puts out about 20 W and many amplifiers need more drive than that, while a KX3 is limited to a few watts for best linearity on some bands. For a 100 W radio, set drive so the amp reaches its rated output without flat-topping, and check ALC levels. Use the radio's amplifier keying output and verify its voltage and current limits against the amp. Most modern rigs use an open-collector or relay-style keying output with limits that should be in the manual. A poorly planned PTT line can cook a transistor in the radio.
What would you check first when building or upgrading a shack, and what are you tackling right now: noise, RF in the shack, amp interfacing, or the layout itself?
Link to comment
https://www.hamradiobase.com/forums/topic/11819-planning-an-hf-shack-around-a-100-w-rig-power-grounding-tuners-filters-and-amp-interfacing/Share on other sites