Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Dual-band mobile rigs: FTM-500D vs ID-5100A vs TM-D710G, plus wiring, noise and mobile etiquette

ci_cover.jpg

This thread is for sorting out what matters when you put a 2 meter / 70 centimeter mobile in a vehicle. Three radios come up constantly: the Yaesu FTM-500D, the Icom ID-5100A and the Kenwood TM-D710G. They all put out roughly 50 watts on VHF and UHF, but they differ in digital modes, APRS support, control head design and features like cross-band repeat. Specs change and variants differ by region, so check each manufacturer's current manual and spec sheet before buying.

Some starting points for discussion:

Choosing a radio. The FTM-500D is built around Yaesu's C4FM digital voice (System Fusion) alongside analog FM. The ID-5100A is a D-STAR radio with a touchscreen and dual receive. The TM-D710G has a built-in TNC and GPS aimed at APRS, and it is often discussed for its cross-band repeat function. Before comparing menus, decide which digital mode your local repeaters actually use. A radio that does a mode nobody near you uses is mostly a very good analog FM rig. Also check whether you want a separable control head. That depends on the model and usually requires an optional cable or kit, so confirm what your exact model supports.

Power wiring and fusing. The usual advice is to run power directly to the battery, not to a cigarette lighter socket or an accessory circuit. Put a fuse in the positive lead as close to the battery terminal as practical, so that a chafed wire anywhere along the run is protected. Use the wire gauge and fuse rating given in your radio's manual, because it accounts for transmit current and cable length. Protect the cable with a rubber grommet where it passes through the firewall, avoid sharp metal edges, and route it away from moving parts and hot components. Many radios also have fuses in their own power cable, which should stay in place.

Mounting. Pick a spot that doesn't interfere with airbag deployment, pedals, or your ability to see and reach the controls without taking your eyes off the road. A bracket bolted to something solid is better than adhesive pads on trim. Leave room behind the radio for airflow, since a 50 W transmitter makes heat during longer transmissions.

Antenna and noise. Most mobile noise problems turn out to be antenna or grounding problems, or interference from the vehicle's own electronics. A roof-center NMO mount with a dual-band antenna is a common setup. Trunk-lip and magnetic mounts can work but depend heavily on a good ground connection to the body. Check SWR on both bands, since an antenna can look fine on 2 meters and be poor on 70 cm. Coax loss matters more at UHF, so don't use a long, cheap run if you can avoid it. For noise, compare the receiver with the engine off, at idle and while revving. Alternator whine that follows engine speed points toward power-lead filtering or routing. Ignition and electronic noise can come from LED lighting, aftermarket chargers and DC-DC converters. Ferrite chokes on power leads, moving the radio's cable away from other wiring and checking the ground path are all worth trying one at a time.

Cross-band repeat. This lets a mobile radio receive on one band and retransmit on the other, so a handheld outside the vehicle can reach a repeater through the mobile's better antenna and power. Not every radio supports it, so check the manual for your exact model. It also raises licensing and operating questions: you remain responsible for identification and for operating within your license privileges and local regulations, and the transmitter is working harder than in normal use. Where are people drawing the line on when it is appropriate?

Etiquette. Driving comes first. Keep transmissions short, pre-program your memories so you aren't navigating menus on the move, and know your local rules on handheld device use while driving. On repeaters, listen before you transmit, leave a gap so others can break in, identify properly, and give priority to emergency traffic. Set your APRS beacon rate sensibly so you don't clutter the channel.

What would you put on a must-do checklist for a first mobile install, and what mistakes do you see most often?

  • Replies 2
  • Views 12
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

For a first install, I'd do the antenna and power cable before touching the radio. Lay out the cable path from battery to cabin and from the roof mount to the radio, and look for pinch points around the door sills, seat rails and the firewall passage. A radio installed with the cables run properly is easier to troubleshoot than one that was hooked up quickly and then needed rewiring.

On fusing, don't treat the radio's built-in fuses as a substitute for a fuse at the battery. Those only protect the radio end of the cable. An inline fuse near the battery protects the long run. Follow whatever the manual says for fuse size and wire gauge.

As for the radios themselves, I'd decide by the repeaters in your area, not by the spec sheet. If your regional repeaters are mostly analog FM with a few D-STAR or Fusion systems, that should push you toward the radio matching the local digital activity, or toward one with strong analog features such as the TM-D710G's APRS integration. It's also worth checking how easy each radio is to operate by feel, since you'll be using it in a moving vehicle.

  • Administrators

On noise, change one thing at a time and write down the result. If you move the power cable, add a ferrite and re-seat the ground at once, you won't know which of them helped. Start with a baseline: engine off, accessories on, then engine running at idle, then with the throttle raised. If the noise changes with RPM, suspect the alternator or ignition system. If it changes when you turn on a certain device, such as a dash cam, charger or LED strip, that device is the likely culprit. Cheap USB chargers are often a worse source of noise than anything related to the engine.

On cross-band repeat, the main thing to remember is that you are still the control operator. You need to be able to identify properly, and the repeat function should only be used where it's allowed by your license and local rules. Using it for long periods can also make the radio run warm, so consider your power setting and ventilation. If you're not sure your model supports it, look in the manual's function list. Don't assume all dual-band mobiles offer it.

For etiquette, the easiest rule is to leave a gap between transmissions on a repeater, especially in a mobile where you may be listening with road noise and not hear someone trying to break in. Keep calls short, and if traffic gets busy or you need to concentrate on the road, wait until you've stopped to continue the conversation.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.