Getting your CW fundamentals right: timing, keys, filters, and when to trust a decoder
- Replies 2
- Views 9
- Created
- Last Reply
Top Posters In This Topic
-
Admin_Terry 1 post
-
Mod_Mike 1 post
A better way to browse. Learn more.
A full-screen app on your home screen with push notifications, badges and more.
CW advice often comes in separate pieces: which paddle to buy, what filter width to use, whether to learn at 20 wpm or 10. Most of it comes down to one thing, which is making the signal you send and the signal you copy fit the standard timing of Morse. Here is a rough framework. Please correct it, add to it, or disagree.
1. Timing is the foundation. A dit is one unit, a dah is three, the space inside a character is one, the space between characters is three, and the space between words is seven. The word PARIS is 50 units, so at 20 wpm a dit is about 60 ms (1200 divided by wpm). Many bad habits trace back to uneven spacing. Running characters together or stretching the gaps makes a sender hard to read even when the speed is modest.
2. Farnsworth and Koch for learning. Farnsworth timing sends each character at a faster speed (say 18 wpm) but stretches the gaps between characters and words so the overall speed is lower. This helps you hear each letter as a sound pattern, not count dits and dahs. The Koch method takes a similar approach: start with just two characters at full speed and add more as you reach a good accuracy level. Both aim to avoid the plateau you can hit when you learn slowly at the wrong character speed and then have to relearn at a higher one.
3. Keys and paddles. A straight key gives you full control of every element, and many operators like it for the rhythm it teaches. A bug (Vibroplex is the best-known maker) generates dits automatically with a pendulum and leaves dahs to you. Iambic paddles drive an electronic keyer that makes both elements. Squeezing both paddles alternates dits and dahs. In iambic mode A the keyer stops when you release. In mode B it adds one more opposite element after release. Neither is better, but it is worth knowing which one your keyer uses, because it can cause extra dits at the end of a letter like C or K. Hand-built paddles from makers such as N3ZN are often chosen for adjustable tension and travel and a smooth feel. Adjusting contact spacing and spring tension to suit your hand usually matters more than the brand.
4. Filters and QSK. A common starting range is 300 to 500 Hz, narrower in crowded contest conditions. Very narrow filters can ring and make it harder to tell where one element ends and the next begins. Set your sidetone or pitch to match the center of the filter. With full break-in (QSK), you can hear the band between your elements, so another station can interrupt you. Semi break-in holds the transmit state for a hang time. If QSK sounds choppy, check that your radio's T/R switching, and any amplifier or external relays, can keep up at your speed.
5. Prosigns and abbreviations. Prosigns are sent as a single character with no gaps. Common ones include AR (end of message), SK (end of contact), BT (break or new paragraph), KN (go ahead, specific station only), and BK (break). Common abbreviations include CQ, DE, UR, RST, QTH, QRS (send slower), QRQ (send faster), QRM (interference), QSB (fading), and TU. In contests, cut numbers such as 5NN (599) are widely used.
6. Skimmers and decoders. CW Skimmer-style software can decode many signals across a band at once and is useful for spotting activity and checking your own copy. Decoders do best with clean, steady signals and struggle with QSB, QRM, and irregular hand-sent timing. They can support your ears but cannot replace them.
Questions for the group: what do you consider the most common timing flaws in sent CW? When would you set the filter wider than you think you need? And how should someone who wants to enter CW contests split practice time between sending and receiving?
Link to comment
https://www.hamradiobase.com/forums/topic/11824-getting-your-cw-fundamentals-right-timing-keys-filters-and-when-to-trust-a-decoder/Share on other sites