Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.5
Wind 385.0 km/s
Aurora 1
Updated 13:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Two-day EMCOMM go-kit: how are you splitting power, antennas, grounding, and noise control?

ci_cover.jpg

I'm sketching a baseline for a two-day field or EMCOMM deployment and want to compare notes on where the design decisions pay off. The target is one HF station (100 W class), one VHF/UHF FM rig for local nets, a laptop for logging and digital modes, and basic lighting, all under a pop-up shelter with no commercial power.

Here is the starting plan. Power is a LiFePO4 battery (12.8 V nominal, 4S) with a DC distribution block, fused close to the battery and Powerpole-terminated branches for each rig. An inverter generator stays on the field as a backup and for recharging, not as the primary supply. Solar is a supplement, sized to offset the overnight draw instead of running the station directly. For antennas, I'm thinking a fiberglass telescoping mast supporting an inverted-V or a fan dipole for HF, plus a roll-up J-pole or small vertical for 2 m/70 cm. Coax is a short run into the shelter with a common-mode choke at the feedpoint.

The questions I'd like to open up are these:

1) With a LiFePO4 battery, is it better to run radios directly from it, or through a regulated DC supply? The pack's voltage sits near 13.3-13.6 V for most of the discharge and then drops sharply near the end, and the BMS cuts off abruptly. Does anyone put a low-voltage alarm or a voltmeter in the main bus so the cutoff doesn't arrive without warning mid-net?

2) What is a sensible generator layout? I'm assuming it goes downwind, well away from the shelter, on its own cord, with a CO alarm in the tent, and that it never runs under cover. But how far away is far enough for RF noise, as opposed to exhaust and sound?

3) How much of a 'ground' do you build in the field? A rod and a few radials won't make an HF antenna work, and a rod is not lightning protection. I'm trying to separate three things: safety bonding, RF counterpoise, and the practical need to keep common-mode current off the coax.

4) What is on your setup and teardown checklist that people tend to forget? I'll start with a polarity check with a meter before the first connection, stakes and guys inspected, the mast location measured against any overhead lines, and a plan for what happens when weather moves in.

  • Replies 2
  • Views 10
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Administrators

On the battery question, the usual practice is direct DC from the LiFePO4 pack, because most modern HF rigs are rated for roughly 13.8 V nominal with a tolerance of around ±15%. A fully charged 4S pack falls comfortably inside that. The part to watch is the knee at the end of discharge. Voltage doesn't sag gradually the way a lead-acid battery does, so a voltmeter alone can mislead you. A coulomb-counting battery monitor (shunt-based) gives a real state of charge, and it is what lets you plan the night instead of guessing. If your pack's BMS has a hard cutoff, set an informal rule to swap to a spare or start charging well before it, since a rig that powers off during a transmission is a bad way to learn where the limit is.

Fuse placement matters more than most people expect. Put the main fuse or breaker as close to the battery terminal as practical, then use smaller fuses per branch. A 100 W HF rig can draw in the neighborhood of 20 A on transmit, so wire gauge and connectors need to be chosen for that with margin, and the leads should be short. Check polarity with a meter at every new connection, and agree on one Powerpole orientation convention for the whole group, because a mixed-up kit is a hazard when multiple operators share gear.

For noise, the biggest offenders in a battery system are often cheap switching devices: USB chargers, 12 V to 5 V adapters, LED lights, and some solar charge controllers. Test them one at a time on the actual band you plan to use, with the receiver on a quiet frequency, before the deployment. If something produces a carpet of birdies or a raised noise floor, a ferrite choke on both leads, or a replacement, usually solves it. An inverter generator is generally quieter than an old conventional one but not noise-free, and its output feeding a switching supply can radiate. Distance and a ferrite on the power cord help, and the final check is simply to run it and listen. Bear in mind that it depends on the specific unit and the band.

  • Moderators

Looking at the antenna side, the single highest-priority item is clearance from power lines. A mast that falls toward an overhead line is a classic cause of serious injury, so site selection should include a measured distance from any line of at least the full height of the mast plus a generous margin, and more is better. If the mast is guyed, think of the guy radius as part of the footprint too. Fiberglass masts help for insulation, but don't treat them as safe against contact with a line, since dirt or moisture on the surface can conduct.

For the HF dipole, a 1:1 current balun or a choke of several turns of coax at the feedpoint keeps common-mode current from turning the coax shield into part of the radiating system. That matters in a tent, where the shield runs near the operator, the laptop, and the rig. If you use an end-fed half-wave, remember it still needs a counterpoise and a choke at the rig end, and it is more sensitive to what's nearby. Whichever you pick, put an antenna analyzer on the run before the net starts, with the antenna at its working height.

On coax, VHF/UHF is where loss bites. A long run of thin RG-58-type cable can eat a meaningful fraction of your power at 2 m and much more at 70 cm, so use a lower-loss cable (LMR-400 class) for anything beyond a short jumper, or put the antenna on the mast closer to the rig. For HF, cable loss is less of a problem, so the lighter option is usually acceptable. Drip loops and strain relief at the shelter entry, and avoid running coax parallel to the power leads for long stretches.

For grounding, the realistic goals are safety and noise, not magic. If you're running a generator, follow the manufacturer's instructions on grounding it, and use GFCI protection on any AC distribution. If storms are in the forecast, the plan should be to disconnect antennas, step away from the mast, and wait, not to rely on a ground rod. Include that decision point and who makes it on the checklist.

For teardown, the order I'd write down is: stop operating and log the end time, power down radios, disconnect antennas and coax, lower the mast, retrieve guys and stakes, then fold the shelter. Count items back against the packing list, and mark any failed gear (a cracked connector, an intermittent cable) for repair so it doesn't return to the kit as if it were good.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.