Before you key up a new repeater: offsets, tones, linking, and the unwritten rules
- Replies 2
- Views 9
- Created
- Last Reply
Top Posters In This Topic
-
Mod_Dan 1 post
-
Mod_Chrissy 1 post
A better way to browse. Learn more.
A full-screen app on your home screen with push notifications, badges and more.
Repeater problems usually trace back to the same few things: a wrong offset, a missing tone, or not realizing the machine is linked to something bigger. This thread is meant as a working checklist, and a place to add what is missing or correct what is region-specific.
Offsets. A repeater listens on one frequency and retransmits on another. Your radio transmits on the repeater's input and listens on its output. The split is fixed per band by the local band plan. In North America the usual offsets are 600 kHz on 2 m, 5 MHz on 70 cm, 1.6 MHz on 1.25 m and 1 MHz on 6 m. In IARU Region 1 the usual 2 m shift is 600 kHz and the usual 70 cm shift is 7.6 MHz. Direction matters too. On 2 m in much of the US, outputs from about 146.600 to 146.999 use a minus offset and 147.000 to 147.399 use a plus offset. That is a convention, not a law of physics, so confirm against the listing or the local coordinator's band plan.
Tones. CTCSS (often called PL, which is Motorola's trade name) is a continuous sub-audible tone between roughly 67 and 254 Hz. Most repeaters require that you transmit a specific tone before they will open. That is the "encode" side. Many repeaters also transmit a tone of their own, and your radio can be set to "tone squelch" so it only opens when it hears that tone. That cuts down on noise and co-channel interference but can also hide a repeater that has changed its tone. DCS is the digital equivalent: a 23-bit code written as a three-digit octal number such as 023, with a polarity (N or I). If a listing gives a DCS code, polarity mistakes are a common reason it does not work. A listing that shows both an uplink tone and a downlink tone may mean they differ, so do not assume one number covers both.
Timers and courtesy. Most repeaters have a time-out timer that drops the transmitter if you hold the key too long. A typical range is a few minutes, but it varies, and some systems have shorter timers during nets. Leave a beat of silence between transmissions so others can break in, and so a courtesy tone can reset the timer. Give your call sign as your regulator requires. In the US that means at least every ten minutes and at the end of a communication. Listen before you transmit. Avoid kerchunking (keying up just to see if you hit it), and use "break" only for something that needs interrupting.
Open versus closed. An open repeater welcomes any licensed operator within its coverage. A closed repeater is restricted to members, sometimes by a tone that is only shared with them. Some systems are "open" but ask for donations or club membership. If the listing says closed or private, ask the trustee or club before using it, not after.
Coordination and directories. In many countries a regional frequency coordinator, usually a volunteer body, assigns repeater pairs so systems do not interfere with each other. Coordination is not a license, but it is the way coordinated machines are protected from new ones. Directories such as RepeaterBook and club or national lists are convenient, but entries go stale. Tones change, repeaters go off the air, and some are listed with the wrong offset. Cross-check against the club's own page if there is one.
Linking. This is where "just a local repeater" can turn into something much bigger. EchoLink connects nodes and repeaters over the internet by node number. IRLP uses dedicated nodes and DTMF commands, with reflectors that tie many nodes together. AllStar is Asterisk-based and gives owners a lot of flexibility to link nodes and repeaters. Yaesu's Wires-X links C4FM repeaters and nodes through rooms. DMR and D-STAR are digital voice systems with their own networks: DMR uses two timeslots, color codes and talkgroups; D-STAR uses callsign routing and reflectors. A linked analog repeater may be playing your audio to listeners elsewhere. Whether a link is active, and how to drop it, is usually posted by the owner.
Questions to get things going: How do you check whether a repeater is currently linked before you call CQ? What do you do when the listing and the actual repeater disagree about the tone? And which clubs publish clear, easy-to-find rules for their systems, and what makes those pages useful?
Link to comment
https://www.hamradiobase.com/forums/topic/11834-before-you-key-up-a-new-repeater-offsets-tones-linking-and-the-unwritten-rules/Share on other sites