Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Rig with no TX and no RX: how do you split the fault before you start swapping parts?

ci_cover.jpg

When a rig is dead on both transmit and receive, the cause is usually something the two paths share, not two separate failures. Here is a bench order that tends to save time. Please correct it or add to it.

1. Power, measured at the board. Don't trust the supply's display. Measure at the rig's DC input and again after the fuse and reverse-polarity protection, with the radio switched on. Look for a voltage that sags under load, a corroded fuse holder, or a power connector that has burned or lost tension. Then check the board regulators one by one (typically 8 V, 5 V and 3.3 V, depending on the design) against the service manual. A dead 5 V or 3.3 V rail can stop the CPU, PLL or DSP while the radio looks powered.

2. Clocks and PLL lock. If the voltages are fine, check that the reference oscillator is running and that the PLL is locked. A scope on the reference clock is the quickest test. An unlocked synthesizer can cause no RX and no TX at once. Most manuals give the expected VCO control voltage at a given frequency, so you can check it with a multimeter.

3. Receive path, working backward. Starting at the speaker and working toward the antenna is often faster than the reverse. Touch the audio amp input and listen for a buzz, which tells you the amp and speaker work. Next, look for noise at the detector or audio stage with the squelch open. Then work back through the IF and mixer to the front-end filters. A stuck antenna relay, a failed band-pass filter switching diode, or a dead preamp bypass relay can kill RX completely.

4. Transmit path. Into a dummy load, check each stage in order: exciter output, driver, bias on the final, and the final's output. If TX is dead and the SWR or power-protection circuit is active, the protection may be holding drive down, so check it early. A faulty ALC or detector can pull drive to zero, and a swapped final will not fix that.

Safety and basics: use a dummy load for every TX test, and use a current-limited bench supply where you can. Take the service manual's block diagram and voltage table as your reference, since they save a lot of guessing. Treat any mains-powered or tube rig with proper isolation and discharge procedures.

Where do you usually start when you open a rig that shows nothing on RX or TX? And which single measurement has told you the most?

  • Replies 1
  • Views 3
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Administrators

I'd begin with the same shared-path logic, but I wouldn't condemn the finals just because TX is dead. Most failed finals have a cause upstream or downstream, and if you swap the transistors without finding it, the new ones usually follow the old.

Before you power up a replacement, check these:

  • Bias network. Look for a failed trimmer, an open resistor, or a bias supply that is too high. Excess bias on a FET stage can overheat it quickly.
  • Gate or base protection. Look for shorted or leaky parts in the drive path and the gate protection.
  • Parasitic oscillation. Failed decoupling capacitors or bad emitter/source bypassing can leave a stage oscillating outside the band. You often see this on a scope as spurious high-amplitude RF with the carrier barely moving, or as power that doesn't track drive.
  • Output network and relays. A burnt low-pass filter relay contact or a cracked capacitor in the filter bank can reflect power back into the finals.
  • The reason it failed. Reflected power from a bad antenna is one cause. A broken SWR fold-back circuit is another, because the radio no longer protects itself.

When you do replace them, set bias to the manual's spec with a current meter in the supply line, into a dummy load, and with the supply current-limited. Bring drive up slowly. If current climbs by itself or the heat sink warms with no RF out, stop and look for oscillation or bias runaway.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.