Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Bench-Testing and Tuning an End-Fed Half-Wave: From Transformer to Trimmed Wire

(0 reviews)

The end-fed half-wave (EFHW) is popular because it is easy to deploy: one wire, one transformer, one run of coax. It is also easy to build badly and then blame the wire. A low SWR reading on an EFHW does not tell you the system is working well. This post covers how to check each part separately so you know what you have before you start trimming.

What you are actually building

A half-wave wire fed at one end has a very high feedpoint impedance, typically in the low thousands of ohms. It varies with height, wire environment and band. The transformer's job is to bring that down to something your radio can accept. The common choice is a 49:1 impedance ratio, which is a 1:7 turns ratio. That maps roughly 2450 ohms to 50 ohms. Some builders use 64:1 instead, which suits slightly higher impedances.

Three things make up the system:

  • The radiator: the wire, cut near a half wavelength on the lowest band.
  • The transformer: a toroid with a few turns, usually a ferrite mix such as 43 or 61 in a size suited to your power level.
  • The return path: an end-fed wire has no obvious second leg, so the coax shield and anything it touches often serve as the counterpoise. That is the part most likely to cause surprises.

Step 1: Test the transformer without the antenna

Before the wire goes up, put a known load on the high-impedance side. A non-inductive resistor near 2.4 kΩ is the usual stand-in, or a series/parallel combination that lands close to it. Then connect your NanoVNA or analyzer at the coax side and sweep the bands you care about.

What you are looking for:

  • A reasonably flat, low SWR across the HF bands you plan to use. It will not be perfect, but it should be broadly consistent.
  • No sharp resonances or sudden jumps, which can point to winding problems or excessive stray capacitance.
  • Behavior that does not change when you move your hand near the box or shift the coax.

If the transformer looks poor into a resistor, fix it now. Common causes are the wrong turns ratio, too few turns on the primary for the lowest band, a core mix unsuited to the frequency, or lead dress that adds stray capacitance. A small compensation capacitor across a winding is a known tweak, but treat its value as something to test, not copy. Changes of tens of picofarads can shift the high-band response noticeably.

Keep in mind that a resistor test tells you about the transformer, not about efficiency. A lossy core can still show a nice SWR because the loss itself looks like a load. For real power handling, ferrite heating is the practical check, and a short key-down test on a dummy load, then a feel of the core afterward, tells you a lot. Build the transformer for more power than you plan to use.

Step 2: Put the wire up and sweep it

Start with the radiator a little long, then trim. Use the rough rule of 468 divided by frequency in MHz to get a half-wave length in feet. For 7.1 MHz that is about 66 feet. Insulation, height and nearby objects change the real resonance, so treat the formula as a starting point.

Sweep from below the lowest band to above the highest and note where the dips fall. An EFHW should show dips near the fundamental and its harmonics, which line up well with 40, 20, 15 and 10 m. Not every dip will be at the right frequency, since real wire does not follow harmonic math exactly.

Trim in small steps. Trim the wire only when the lowest-band dip is below the frequency you want. Cutting a wire shorter raises the resonant frequency. Fold the extra length back instead of cutting it until you are sure of the final value.

Step 3: Treat the coax as part of the antenna

If the SWR changes when you touch the coax, move it, or change its length, current is flowing on the outside of the shield. That means the coax is acting as the missing counterpoise, or as part of the radiator. This is not always bad, but it makes results unpredictable and can bring noise into the receiver or RF into the shack.

Useful experiments:

  • Add a common-mode choke on the coax a short distance from the transformer, then re-sweep. Note whether the resonances move.
  • Add a deliberate counterpoise wire, a few percent of a wavelength or longer, attached at the ground side of the transformer. See whether the SWR becomes less sensitive to coax position.
  • Change the coax length by a few feet and see whether SWR on any band shifts. Large shifts suggest the shield is carrying significant current.

Change only one thing at a time. If you add a choke and move the wire in the same session, you will not know which mattered.

Reading the results sensibly

SWR measures how well the load matches the line. It does not measure radiation. A wire that is poorly placed, close to metal, or partly absorbed by a lossy transformer can still show a pleasing curve. To judge real improvement, pair the sweep with a comparison on air or a noise check:

  • Listen to the same stable signal or beacon before and after a change, from the same time of day if possible.
  • Compare receive noise level on a quiet band with the old antenna and the new one.
  • Log reports from the same stations if you can, but treat propagation changes as a caveat.

Keep a simple before-and-after record

A small table of your own makes later troubleshooting much easier. Record:

  • Wire length, height at each end, and layout.
  • Transformer details: core, turns, any capacitor value.
  • Coax type and length, and where any choke sits.
  • SWR minimum and its frequency on each band.
  • Notes on noise level and any received signals used for comparison.

If something changes weeks later, a sweep compared with the saved one will point to water in a connector, a loose joint or a shifted wire.

Common failure patterns

  • Good SWR but weak signals: suspect transformer loss, a wire hanging near metal, or a lot of feedline radiation.
  • One band is poor, the rest fine: check the compensation capacitor, the wire length for that harmonic, and the coax routing.
  • SWR changes with weather: look at connector sealing and the transformer enclosure for moisture.
  • RF in the shack on one band: add or improve common-mode choking and review the coax run.

A safety note

Keep the wire well away from power lines and plan the supports so nothing can fall onto them. An end-fed wire carries high RF voltage at the far end, so keep it out of reach of people and pets while transmitting. For storms, disconnect and move the coax away from the radio. A disconnected antenna is not lightning-proof, but it is far better than leaving it attached to your equipment.

The sequence is simple: check the transformer on the bench, sweep the wire, deal with the coax, then compare real receive and transmit results. It takes longer than just trimming the wire until the SWR looks right, but you end up with an antenna you understand, and notes to fall back on when something changes.

0 Comments

Recommended Comments

There are no comments to display.

Guest
Add a comment...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.