Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Entries in this blog

A common vertical-antenna surprise: you add radials, expecting everything to improve, and the SWR meter gets worse. Or you start with a vertical that shows a lovely 1.2:1 and discover it radiates poorly. Both outcomes come from the same fact. SWR measures impedance match, not efficiency. Once you separate those two ideas, radial experiments make a lot more sense.

What the feedpoint resistance is made of

At resonance, the resistance you see at the base of a vertical is the sum of several parts:

  • Radiation resistance, the part that actually makes signal. For a quarter-wave vertical over a good ground this is roughly 35–37 Ω.
  • Ground loss resistance, which comes from current flowing through lossy soil under and around the antenna.
  • Conductor and coil losses, usually small on a full-size wire or tube vertical but significant on loaded or shortened designs.

Power in the loss resistances turns into heat. If ground loss adds 15 Ω to a 36 Ω radiation resistance, the feedpoint reads about 51 Ω. The SWR looks perfect, but nearly 30% of your power is going into the dirt. Add radials and the ground loss drops, the feedpoint resistance falls toward 36 Ω, and the SWR on 50 Ω coax creeps up to about 1.4:1. The antenna got better and the meter got worse.

Use R and X, not just SWR

A NanoVNA is ideal here because it can display resistance and reactance, not only SWR. Before changing anything, record:

  • The frequency where reactance crosses zero (resonance).
  • The resistance at that frequency.
  • The SWR sweep across the whole band, saved or screenshotted.

After each change, repeat the same sweep with the same cable and calibration. Calibrate at the end of the cable or at the antenna feedpoint when you can. A long coax run, if not accounted for, will smear the readings. If you must measure through the coax, use a length of known electrical behavior, such as a half-wavelength multiple, or accept that the numbers are approximate and compare only like with like.

A sensible way to run a radial experiment

Change one variable at a time. A simple progression for a ground-mounted vertical might look like this:

  1. Measure with a small number of radials, say four.
  2. Double the count, re-measure, and note the change in resistance and resonant frequency.
  3. Keep doubling as far as is practical, watching how much each step changes the numbers.

You will typically see big changes at first and smaller ones later. Published field measurements by antenna researchers have shown this pattern of diminishing returns for buried and ground-laid radials: going from a handful to a few dozen helps a lot, while going far beyond that gives smaller gains. Your own soil will set where your curve flattens, which is exactly why measuring beats guessing.

Radial length matters less than count for ground-laid systems. Many short radials usually beat a few long ones, because the goal is to intercept the return currents near the base where they are strongest. Don't expect the numbers to be identical to a textbook, since the soil under your lawn isn't a textbook.

Elevated radials behave differently

If the radials are raised off the ground, a few resonant ones can do the job, because they form a reasonably self-contained counterpoise and couple less to the soil. Two to four tuned quarter-wave radials is a common starting point. Drooping them downward at an angle also raises the feedpoint resistance toward 50 Ω, which can give a natural match to coax without extra hardware. Resonant elevated radials do need trimming, and the VNA will tell you when they are close: look for the feedpoint reactance and the resonant frequency to settle as you adjust.

Keep the radial ends away from people and pets. They can carry high voltage at the tips, especially at higher power levels.

Check the choke too

A vertical with an inadequate ground system tends to push common-mode current onto the feed line, because the coax shield becomes part of the antenna system. If your readings change when you move or touch the coax, or if the noise floor is unusually high, add a common-mode choke near the feedpoint and compare again. It is a separate fix from the radials, but the two interact, so test them separately and note each result.

Measuring the real-world benefit

Impedance readings tell you what the antenna is doing electrically, but not directly how well it radiates. A few ways to check, each with caveats:

  • Receive comparison. Switch between the new and old setup on the same band and compare signal-to-noise ratio on a steady signal such as a beacon or broadcast station. This is a fair test only if you switch quickly, since propagation drifts.
  • Remote reports. Spotting networks such as WSPR and the Reverse Beacon Network let you compare how you are heard. Alternate configurations in short, repeated intervals, because a single before-and-after pair can be skewed by band conditions.
  • Local field strength. A simple field-strength probe at a fixed spot some distance away can show relative changes, as long as you keep the probe position identical and the power constant.

None of these is laboratory grade, but a trend that holds across several repeated trials is meaningful.

Keep a log

Write down the date, band, radial count and layout, feed line, choke, and VNA readings for each stage. Weather and soil moisture can shift ground-loss numbers noticeably, so repeating a measurement on a different day is a useful sanity check. If dry and wet soil give different feedpoint resistances, that tells you something about how much of your antenna's performance depends on the ground.

Takeaways

  • SWR is a match indicator, not an efficiency indicator.
  • A falling feedpoint resistance after adding radials usually means less ground loss, even if SWR rises a little.
  • Add radials in steps and measure each step; expect diminishing returns.
  • Test choke and radial changes separately so you know what each one did.
  • Confirm with on-air or receive comparisons, repeated enough times to filter out propagation changes.

A vertical that reads a bit higher in SWR but sends more of your power into the air is a better antenna than one that looks perfect on the meter and warms the lawn. Let the R and X numbers guide you, and treat a lower SWR as a bonus rather than the goal.

The end-fed half-wave (EFHW) is popular because it is easy to deploy: one wire, one transformer, one run of coax. It is also easy to build badly and then blame the wire. A low SWR reading on an EFHW does not tell you the system is working well. This post covers how to check each part separately so you know what you have before you start trimming.

What you are actually building

A half-wave wire fed at one end has a very high feedpoint impedance, typically in the low thousands of ohms. It varies with height, wire environment and band. The transformer's job is to bring that down to something your radio can accept. The common choice is a 49:1 impedance ratio, which is a 1:7 turns ratio. That maps roughly 2450 ohms to 50 ohms. Some builders use 64:1 instead, which suits slightly higher impedances.

Three things make up the system:

  • The radiator: the wire, cut near a half wavelength on the lowest band.
  • The transformer: a toroid with a few turns, usually a ferrite mix such as 43 or 61 in a size suited to your power level.
  • The return path: an end-fed wire has no obvious second leg, so the coax shield and anything it touches often serve as the counterpoise. That is the part most likely to cause surprises.

Step 1: Test the transformer without the antenna

Before the wire goes up, put a known load on the high-impedance side. A non-inductive resistor near 2.4 kΩ is the usual stand-in, or a series/parallel combination that lands close to it. Then connect your NanoVNA or analyzer at the coax side and sweep the bands you care about.

What you are looking for:

  • A reasonably flat, low SWR across the HF bands you plan to use. It will not be perfect, but it should be broadly consistent.
  • No sharp resonances or sudden jumps, which can point to winding problems or excessive stray capacitance.
  • Behavior that does not change when you move your hand near the box or shift the coax.

If the transformer looks poor into a resistor, fix it now. Common causes are the wrong turns ratio, too few turns on the primary for the lowest band, a core mix unsuited to the frequency, or lead dress that adds stray capacitance. A small compensation capacitor across a winding is a known tweak, but treat its value as something to test, not copy. Changes of tens of picofarads can shift the high-band response noticeably.

Keep in mind that a resistor test tells you about the transformer, not about efficiency. A lossy core can still show a nice SWR because the loss itself looks like a load. For real power handling, ferrite heating is the practical check, and a short key-down test on a dummy load, then a feel of the core afterward, tells you a lot. Build the transformer for more power than you plan to use.

Step 2: Put the wire up and sweep it

Start with the radiator a little long, then trim. Use the rough rule of 468 divided by frequency in MHz to get a half-wave length in feet. For 7.1 MHz that is about 66 feet. Insulation, height and nearby objects change the real resonance, so treat the formula as a starting point.

Sweep from below the lowest band to above the highest and note where the dips fall. An EFHW should show dips near the fundamental and its harmonics, which line up well with 40, 20, 15 and 10 m. Not every dip will be at the right frequency, since real wire does not follow harmonic math exactly.

Trim in small steps. Trim the wire only when the lowest-band dip is below the frequency you want. Cutting a wire shorter raises the resonant frequency. Fold the extra length back instead of cutting it until you are sure of the final value.

Step 3: Treat the coax as part of the antenna

If the SWR changes when you touch the coax, move it, or change its length, current is flowing on the outside of the shield. That means the coax is acting as the missing counterpoise, or as part of the radiator. This is not always bad, but it makes results unpredictable and can bring noise into the receiver or RF into the shack.

Useful experiments:

  • Add a common-mode choke on the coax a short distance from the transformer, then re-sweep. Note whether the resonances move.
  • Add a deliberate counterpoise wire, a few percent of a wavelength or longer, attached at the ground side of the transformer. See whether the SWR becomes less sensitive to coax position.
  • Change the coax length by a few feet and see whether SWR on any band shifts. Large shifts suggest the shield is carrying significant current.

Change only one thing at a time. If you add a choke and move the wire in the same session, you will not know which mattered.

Reading the results sensibly

SWR measures how well the load matches the line. It does not measure radiation. A wire that is poorly placed, close to metal, or partly absorbed by a lossy transformer can still show a pleasing curve. To judge real improvement, pair the sweep with a comparison on air or a noise check:

  • Listen to the same stable signal or beacon before and after a change, from the same time of day if possible.
  • Compare receive noise level on a quiet band with the old antenna and the new one.
  • Log reports from the same stations if you can, but treat propagation changes as a caveat.

Keep a simple before-and-after record

A small table of your own makes later troubleshooting much easier. Record:

  • Wire length, height at each end, and layout.
  • Transformer details: core, turns, any capacitor value.
  • Coax type and length, and where any choke sits.
  • SWR minimum and its frequency on each band.
  • Notes on noise level and any received signals used for comparison.

If something changes weeks later, a sweep compared with the saved one will point to water in a connector, a loose joint or a shifted wire.

Common failure patterns

  • Good SWR but weak signals: suspect transformer loss, a wire hanging near metal, or a lot of feedline radiation.
  • One band is poor, the rest fine: check the compensation capacitor, the wire length for that harmonic, and the coax routing.
  • SWR changes with weather: look at connector sealing and the transformer enclosure for moisture.
  • RF in the shack on one band: add or improve common-mode choking and review the coax run.

A safety note

Keep the wire well away from power lines and plan the supports so nothing can fall onto them. An end-fed wire carries high RF voltage at the far end, so keep it out of reach of people and pets while transmitting. For storms, disconnect and move the coax away from the radio. A disconnected antenna is not lightning-proof, but it is far better than leaving it attached to your equipment.

The sequence is simple: check the transformer on the bench, sweep the wire, deal with the coax, then compare real receive and transmit results. It takes longer than just trimming the wire until the SWR looks right, but you end up with an antenna you understand, and notes to fall back on when something changes.

If your SWR shifts when someone walks past the feed line, your receive noise changes when you reroute a cable, or you get a tingle from the rig's metalwork on 40 meters, you probably have common-mode current. It is one of the most common hidden variables in amateur antenna systems, and it can make good antennas look bad and bad antennas look mysterious.

What common-mode current actually is

Current on a coax feed line should be equal and opposite on the center conductor and the inside of the shield. That is differential-mode current, and it stays inside the cable. If the antenna is unbalanced or poorly isolated, some current can flow on the outside of the shield instead. That is common-mode current. Once it is there, your feed line is part of the antenna. It radiates, picks up noise from household wiring, and brings RF back into the shack.

Several setups invite it:

  • A center-fed dipole fed directly with coax and no choke, especially where the coax drops away close to one leg.
  • An off-center-fed or end-fed antenna with a small or missing counterpoise. The coax shield often becomes the counterpoise by default.
  • A vertical with few or short radials, where the shield provides the return path the ground system should have.
  • Any antenna near its own feed line, house wiring, or a metal mast, where coupling is easy.

Symptoms worth taking seriously

  • SWR depends on the coax. If the reading changes when you move the cable, coil it differently, or add a few feet of length, the shield is participating in the antenna.
  • RF in the shack. Distorted audio, a hot microphone or keyer, computer interface dropouts, or a rig that behaves differently with power level can all point to RF returning on cables.
  • Noise that tracks the feed line. If the receive noise floor changes when you shift the coax or add a choke, the cable is acting as a noise antenna.
  • Pattern surprises. A dipole that seems to favor strange directions or lacks the expected nulls may have a radiating feed line.

None of these proves common-mode current on its own, but together they are a strong hint. The good news is that the test is cheap and quick.

A simple diagnostic sequence

Change one thing at a time and write down what you see. Here is a sequence that works with a NanoVNA or an ordinary antenna analyzer.

  1. Baseline sweep. Measure SWR across the band of interest with the cable in its normal position. Save the trace or note the minimum SWR frequency, SWR at that point, and SWR at the band edges.
  2. Disturb the coax. Move the feed line, lay a section on the ground, or add a short extension. Sweep again. A large shift is a flag. A clean system will change much less, though some change from loss and mismatch is normal.
  3. Add a temporary choke. Clip clamp-on ferrites or coil the coax into a rough choke near the feedpoint. Sweep again and compare.
  4. Check receive noise. At a fixed frequency with the same receiver settings, compare the noise floor before and after. Use the S-meter or a software spectrum display, and try to compare under similar conditions, since band noise varies by time of day.
  5. Listen for RF in the shack. At modest power, see whether audio distortion, interface problems, or other symptoms improve.

If the SWR curve becomes more stable and predictable and the noise drops, you have found something real. If nothing changes, the problem is likely elsewhere, such as a bad connector, a poor ground, a local noise source, or the antenna itself.

Building a decent choke

A common-mode choke is a high impedance placed in series with the shield's outside path. It does not affect the signal inside the coax. The goal is high impedance across the band, and the usual rule of thumb is several thousand ohms, with 5 kΩ or more often cited. The details depend on your antenna and noise environment.

The two common approaches are:

  • Ferrite beads or cores on the coax. Stack a number of cores over the cable, or wind turns through a toroid, using a mix suited to your bands. Mix 31 is often used for lower HF, and mix 43 tends to suit higher HF and VHF. Check the manufacturer's data for your frequencies, because not all ferrite is equal.
  • Coiled coax. A choke made by winding coax into a coil is simple and robust, but its performance depends on coil size and the bands you use. It tends to work better on a limited range than across all of HF.

Do not trust a choke because it looks professional. Measure it if you can. With a NanoVNA, you can use a series-through test fixture or a documented S21 method on the choke wound on a short sample of cable. Compare designs by their impedance on your bands, not by how many cores you used.

Where to put it

The most useful position is usually right at the feedpoint, where you want to stop current from getting onto the coax in the first place. A second choke where the cable enters the building can help if noise or RF is still coming in along the line. For end-fed antennas, treat the choke and counterpoise as one system. A choke can stop the shield from acting as the counterpoise, which means the antenna may then need a real counterpoise wire to work well.

One more caution: chokes can heat up at high power if they are lossy or poorly matched to the band. Check the ratings and temperature on a test run before you leave a design in service at full power.

Reading the before-and-after results

A lower SWR is not the same as a better antenna. A choke may make SWR look worse, and still improve the system, because the coax is no longer an accidental radiator that was helping the match. Look at the whole picture:

  • Is the SWR curve stable when you touch or move the cable?
  • Is the noise floor lower on the bands you use?
  • Are shack problems reduced?
  • Do on-air reports or your own receive comparisons suggest better performance?

For a clean log, record the date, weather, feed line length, choke type and position, bands tested, the SWR minimum and bandwidth, noise floor at a fixed frequency, and any shack symptoms. Photograph the setup too. When you try a different choke or a new counterpoise next month, you will have a fair comparison rather than a hazy memory.

What a choke does not fix

A choke is not a substitute for a good antenna, a decent radial or counterpoise system, or proper grounding. It does not provide lightning protection. Safety grounding and surge protection are separate jobs, and a choke does not replace them. It also will not cure noise produced at your own house if the source is radiating directly into the antenna. For that, you still need noise hunting: switch off breakers, test one device at a time, and use a battery-powered receiver to trace the strongest area.

Bottom line

If your station behaves differently when you touch the coax, start with the feed line. Take a baseline sweep, add a temporary choke, and compare SWR stability, noise, and shack behavior. It is one of the cheapest experiments in amateur radio, and the results often tell you exactly where to work next.

Most station upgrades start the same way: something sounds noisy, an SWR reading looks odd, or a band feels dead, and the instinct is to put up a bigger antenna. Sometimes that's right. More often, a few simple measurements will show where the real problem is, and they give you proof when the fix works. Here is a measurement-first workflow that applies to dipoles, verticals, loops, and end-fed halfwaves alike.

Start with a baseline

Before touching anything, write down what the station does today. You can't claim an improvement without a "before." A useful baseline takes about twenty minutes:

  • SWR or impedance sweep across each band you care about, taken with the same instrument each time.
  • Noise floor on a few quiet frequencies, with the S-meter or a software reading, at set times of day.
  • Receive comparison using a known beacon, a stable broadcast signal, or a decoded-spot tool, noting the antenna in use.
  • A photo and sketch of the layout: feed line route, ground connections, and power supplies.

Keep the notes in one place, like a notebook or spreadsheet. A simple template works: date, weather, antenna, feed line, choke used, band, SWR, noise reading, and remarks.

Using a NanoVNA honestly

A NanoVNA is excellent for finding resonance, checking a tuner-free match, and trimming wire lengths. A few habits keep its readings meaningful:

  • Calibrate at the point of measurement. Use short-open-load standards at the end of the cable or adapter chain you're testing. Recalibrate when you change the frequency range.
  • Know what you're measuring. At the end of a long, lossy coax, the cable improves the apparent SWR. A low reading at the radio end can hide a poor antenna or a high-loss line. Measuring at the feedpoint, or checking the cable's loss separately, tells you more.
  • Keep the instrument and cables away from the antenna's near field. Common-mode current on the outside of the coax can shift readings when you touch or move the cable.
  • Remember that SWR is not efficiency. A dummy load has a perfect SWR and radiates nothing. A low SWR only says the feedpoint is matched to the line, not that the antenna is working well.

Trimming a dipole

For a wire dipole, the process is mechanical. Sweep it, find where the SWR minimum or reactance zero-crossing falls, and compare it with the target. If the resonance is too low in frequency, the wire is too long; shorten both legs equally. If it's too high, add length. Make changes in small steps, because a few centimeters on each leg can move resonance by a surprising amount on the higher bands. Remember that height, nearby trees, sloping legs, and ground quality all shift the result, so measure the antenna where it will actually be used, not on the lawn.

End-fed halfwave builds

An EFHW depends on a high-impedance transformer, commonly 49:1 or 64:1, to match the antenna's feedpoint, which is typically in the thousands of ohms. The transformer's core, winding, and any stray capacitance all affect its behavior across bands. Because an EFHW has no balanced feedpoint, the coax shield often becomes part of the antenna, so a common-mode choke near the transformer is worth considering, or a short counterpoise wire. Test the whole assembly with the actual feed line attached. If the SWR changes when you move or touch the coax, the shield is carrying current.

Baluns and common-mode chokes

These two terms get mixed up, but in practice most hams need a choke: a device that adds impedance to current flowing on the outside of the coax shield. Symptoms of common-mode trouble include:

  • RF in the shack, such as a hot microphone, a tingling chassis, or computer glitches during transmit.
  • Noise that changes when you touch or reposition the coax.
  • Distorted antenna patterns and SWR that varies with cable layout.

A common approach is winding coax through a ferrite core, such as a type 31 mix for much of HF, or using a stack of beads. Choke performance depends on the core material, number of turns, and frequency, so check the manufacturer's data and, if possible, measure the choke's impedance with the NanoVNA. A choke that is excellent on 40 meters may do little on 10 meters. Placing one at the feedpoint and another at the shack entrance is a typical way to cover both ends.

Radials and ground systems

A vertical is only half an antenna, and the ground system is the other half. For a ground-mounted vertical, many shorter radials generally beat a handful of long ones, because they reduce loss in the soil near the base. For an elevated vertical, a small number of resonant radials can work well, since they're off the ground and loss is lower. Whatever the layout, check the match before and after adding radials. A falling SWR can be misleading: in poor ground setups, adding radials may raise SWR slightly while actually improving radiated signal, because loss resistance is dropping out of the system. Use a receive comparison or field-strength check alongside the VNA.

Grounding versus lightning protection

These are separate goals. An RF ground helps some antennas work. A safety and lightning ground protects people and equipment. Good practice includes:

  • A single-point entrance panel where coax, rotor cables, and control lines are bonded to a ground rod system.
  • Bonding the station ground to the building's electrical ground, following local code.
  • Surge protectors on coax and control lines, with clear understanding that they reduce risk and do not guarantee protection from a direct strike.
  • Disconnecting and moving coax away from the radios during storms if that's practical.

For specifics, follow your local electrical code and consider hiring a qualified electrician or lightning protection professional. This is an area where guesswork is expensive and potentially dangerous.

Hunting noise methodically

Noise hunting rewards a systematic approach over random ferrite-clipping. Try this sequence:

  1. Run a battery-powered receiver with a simple antenna in the shack to see whether the noise is local or arrives from outside.
  2. Switch off breakers one at a time, if safe, and watch the noise level.
  3. Check the usual suspects: switching power supplies, LED lights, chargers, dimmers, solar equipment, and network gear.
  4. Walk outside with a portable AM radio or handheld receiver to follow the noise toward its source, such as a utility pole or neighbor's device.
  5. Add chokes or filters at the source only after identifying it, then re-measure.

Receive antennas also matter. A small loop or a well-separated vertical can sometimes hear less local noise than a transmit antenna right above the house wiring.

Close the loop with an "after"

After each change, repeat the baseline measurements under similar conditions and record them next to the originals. Change one thing at a time, even if it feels slow. If you replace the feed line, add a choke, and move the antenna in one afternoon, you'll never know which change mattered. A tidy before-and-after log also makes future troubleshooting easier, because you can tell whether a new problem is a real fault or a seasonal change, like wet trees detuning a wire.

The best station improvements are rarely glamorous. They're a sweep, a note, a small fix, and another sweep. Do that consistently, and your antenna projects become repeatable experiments rather than guesses.


Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.