Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.5
Wind 385.0 km/s
Aurora 1
Updated 13:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Mod_Chad

Moderators
  • Joined

  • Last visited

  1. On changing calls without going vanity, there's the systematic call sign change. It lets you request a different sequentially assigned call, which can be useful if you want a shorter format and you qualify for it, for instance after upgrading. It is not the same as choosing a particular call, so don't expect it to produce one you want. After any change, update everything that references the old call: your club rosters, logging software, LoTW and other logbook services, QSL information, repeater control operator listings and so on. Many of these treat a new call as a separate identity, and a few need paperwork to link the old and new records. And for special events, keep in mind that the on-air ID is still required. If you're using a 1x1 call, make sure everyone operating knows the rules for it, including the dates it's valid, and that each operator holds a license appropriate for the bands and modes they're using.
  2. For the two-fer question, the safest approach is to treat the log as covering every reference you were in at the time of the contacts, and to confirm the exact upload method in the current POTA documentation instead of relying on memory. Log files are the part that fails most often, so a quick test with a few contacts before the real activation is cheap insurance. Hunters have a part in this too. Write the full call sign as you copy it, and don't assume you know the activator's exact park from a spot. If an activator is at a two-fer, ask which reference they're using so you get the credit you expect. It's also worth waiting for the activator to confirm the contact, especially on weak signals, because a busted call won't match anything in their uploaded log. On the antenna side, a simple, quick-to-deploy setup beats a complicated one. Time spent fiddling with a perfect install can eat into the window when you could have been making contacts.
  3. Your plan is sound, and the order matters: text first, practice tests second. Tests used as diagnostics work much better than tests used as the main source of learning. On the math, the Technician exam is gentler than it looks. Most calculation questions are one-step: Ohm's law with simple numbers (12 volts across 4 ohms is 3 amps), power from volts times amps, or the wavelength rule of thumb. If you can rearrange E = I × R and P = I × E, you've covered most of it. Learn to recognize which unknown the question is asking for and which formula contains the other two values. Sketching the triangle or wheel helps, but writing out the algebra each time is faster to learn than recalling a picture. For band and privilege questions, tie each fact to something concrete. Technicians have all amateur privileges above 30 MHz, which includes the popular VHF/UHF bands: 2 meters (144–148 MHz), 1.25 meters (222–225 MHz) and 70 cm (420–450 MHz). Technicians also get limited HF privileges: CW on parts of 80, 40 and 15 meters, and some phone/data privileges on a segment of 10 meters. Don't rely on my summary for the exact segments or power limits. Check the current Part 97 band plan chart, since those are the details questions test. For repeaters, the key ideas are input versus output frequency, the offset (commonly 600 kHz on 2 meters, and 5 MHz on 70 cm), and CTCSS tones used to open a repeater's receiver. Those matter in practice. When you key up, you're transmitting on the repeater's input frequency, and the repeater retransmits on its output. If you understand that, offset questions answer themselves.
  4. On new gear and firmware, a few habits save headaches. Read the release notes before updating, especially for transceivers with touchscreens, SDR architecture or network features. Back up your memory channels and settings first, because some updates reset menus. If the manufacturer publishes a known-issues list or a support forum thread, look at it before you flash. For new rigs, I'd wait for independent measurements before forming a strong opinion. Lab-style results such as receiver dynamic range, phase noise and transmitted signal quality tell you more than a feature list. Also check ease of use for the way you operate: contesting, portable, digital modes, satellite or a basic rag-chew each stress different things. Club newsletters and nets are also worth following. They're often the quickest way to learn about local repeater changes, license exam sessions, field day plans and swap meets, none of which show up in national coverage. If your club doesn't have a shared place for news, a simple monthly email or a pinned thread can make a big difference.
  5. One useful change is to treat ALC as a limit rather than a target. If it only moves on the loudest syllables, the rig is probably operating linearly. If it moves on every word, mic gain or the processor drive is usually too high. On compression, a number on a dial doesn't tell you much, because rigs scale it differently. A better test is to make a recording with the processor off and again with each setting, then listen at low volume through a small speaker. The best choice is the one where the words are easier to follow, not necessarily the one with the biggest level change. Increased background noise between words is a sign it has gone too far.
  6. On the "what keeps coming back" question, the usual suspect in many groups is power and logistics, not radio technique. Things like dead batteries, a missing adapter, no spare coax, no paper and pencil, or nobody knowing who has the key to the building. One fix is a simple kit checklist that is checked off during an exercise rather than assumed. Then the after-action report can say "checklist found three missing items" instead of leaving it to memory. For SET specifically, I would add injects: small surprises delivered by whoever is playing the served agency. For example, the primary repeater is declared "down" at a set time, or a message arrives with an unclear address, or the shelter manager changes the request halfway through. These test decision-making and not only the ability to follow a script. Keep the injects realistic and modest, so that the exercise is a stretch rather than a collapse.
  7. The simplest test I would recommend is the 6 dB step check. Note the strength of a suspect signal, then add 6 dB of attenuation or drop the gain by a known amount. A genuine signal should fall by about that much. A product from overload or intermodulation usually falls by a different amount, often more than the step, and may vanish or shift. Images from a strong signal elsewhere in the capture window behave the same way. If the phantom signals disappear with a small attenuation change and the real ones barely move, you were overloading. For setting gain, a useful rule is to connect the antenna, watch the noise floor, and increase gain until the floor rises by only a few dB compared with a terminated input. Past that point you are mostly amplifying noise and consuming headroom. On the RTL-SDR family that often means a lower gain setting than people expect, especially with a good antenna and a strong local signal environment. On SDRplay, the LNA state and IF gain reduction work together, so it is worth changing them one at a time and using the built-in notch filters (broadcast AM, FM, DAB where fitted) before increasing gain. Airspy users get a similar benefit from the gain linearity presets, which trade sensitivity for a more linear response. HackRF is a different case. It is a wide-coverage, transmit-capable tool with 8-bit sampling, so it benefits most from external filtering and careful use of its RF amp, LNA and VGA stages. Leaving the front-end amp on by default is a common cause of overload in a strong signal environment.
  8. One thing worth adding on LoTW: check your station location details before you upload a big batch. If the DXCC entity, grid or zone information in TQSL doesn't match where you actually operated, the QSOs may be signed with the wrong information and won't help you. Portable and mobile operators especially should create a separate station location for each place they operate from. It's much easier to set that up first than to try to fix a pile of rejected or mismatched records later. Also, when a QSO doesn't match, don't assume the other station is ignoring LoTW. A mode mismatch (for example, one side logged FT8 and the other logged generic data) is usually handled because LoTW groups modes, but a wrong band or a date error can stop the match. It's worth comparing both logs when a confirmation looks overdue.
  9. A common vertical-antenna surprise: you add radials, expecting everything to improve, and the SWR meter gets worse. Or you start with a vertical that shows a lovely 1.2:1 and discover it radiates poorly. Both outcomes come from the same fact. SWR measures impedance match, not efficiency. Once you separate those two ideas, radial experiments make a lot more sense. What the feedpoint resistance is made of At resonance, the resistance you see at the base of a vertical is the sum of several parts: Radiation resistance, the part that actually makes signal. For a quarter-wave vertical over a good ground this is roughly 35–37 Ω. Ground loss resistance, which comes from current flowing through lossy soil under and around the antenna. Conductor and coil losses, usually small on a full-size wire or tube vertical but significant on loaded or shortened designs. Power in the loss resistances turns into heat. If ground loss adds 15 Ω to a 36 Ω radiation resistance, the feedpoint reads about 51 Ω. The SWR looks perfect, but nearly 30% of your power is going into the dirt. Add radials and the ground loss drops, the feedpoint resistance falls toward 36 Ω, and the SWR on 50 Ω coax creeps up to about 1.4:1. The antenna got better and the meter got worse. Use R and X, not just SWR A NanoVNA is ideal here because it can display resistance and reactance, not only SWR. Before changing anything, record: The frequency where reactance crosses zero (resonance). The resistance at that frequency. The SWR sweep across the whole band, saved or screenshotted. After each change, repeat the same sweep with the same cable and calibration. Calibrate at the end of the cable or at the antenna feedpoint when you can. A long coax run, if not accounted for, will smear the readings. If you must measure through the coax, use a length of known electrical behavior, such as a half-wavelength multiple, or accept that the numbers are approximate and compare only like with like. A sensible way to run a radial experiment Change one variable at a time. A simple progression for a ground-mounted vertical might look like this: Measure with a small number of radials, say four. Double the count, re-measure, and note the change in resistance and resonant frequency. Keep doubling as far as is practical, watching how much each step changes the numbers. You will typically see big changes at first and smaller ones later. Published field measurements by antenna researchers have shown this pattern of diminishing returns for buried and ground-laid radials: going from a handful to a few dozen helps a lot, while going far beyond that gives smaller gains. Your own soil will set where your curve flattens, which is exactly why measuring beats guessing. Radial length matters less than count for ground-laid systems. Many short radials usually beat a few long ones, because the goal is to intercept the return currents near the base where they are strongest. Don't expect the numbers to be identical to a textbook, since the soil under your lawn isn't a textbook. Elevated radials behave differently If the radials are raised off the ground, a few resonant ones can do the job, because they form a reasonably self-contained counterpoise and couple less to the soil. Two to four tuned quarter-wave radials is a common starting point. Drooping them downward at an angle also raises the feedpoint resistance toward 50 Ω, which can give a natural match to coax without extra hardware. Resonant elevated radials do need trimming, and the VNA will tell you when they are close: look for the feedpoint reactance and the resonant frequency to settle as you adjust. Keep the radial ends away from people and pets. They can carry high voltage at the tips, especially at higher power levels. Check the choke too A vertical with an inadequate ground system tends to push common-mode current onto the feed line, because the coax shield becomes part of the antenna system. If your readings change when you move or touch the coax, or if the noise floor is unusually high, add a common-mode choke near the feedpoint and compare again. It is a separate fix from the radials, but the two interact, so test them separately and note each result. Measuring the real-world benefit Impedance readings tell you what the antenna is doing electrically, but not directly how well it radiates. A few ways to check, each with caveats: Receive comparison. Switch between the new and old setup on the same band and compare signal-to-noise ratio on a steady signal such as a beacon or broadcast station. This is a fair test only if you switch quickly, since propagation drifts. Remote reports. Spotting networks such as WSPR and the Reverse Beacon Network let you compare how you are heard. Alternate configurations in short, repeated intervals, because a single before-and-after pair can be skewed by band conditions. Local field strength. A simple field-strength probe at a fixed spot some distance away can show relative changes, as long as you keep the probe position identical and the power constant. None of these is laboratory grade, but a trend that holds across several repeated trials is meaningful. Keep a log Write down the date, band, radial count and layout, feed line, choke, and VNA readings for each stage. Weather and soil moisture can shift ground-loss numbers noticeably, so repeating a measurement on a different day is a useful sanity check. If dry and wet soil give different feedpoint resistances, that tells you something about how much of your antenna's performance depends on the ground. Takeaways SWR is a match indicator, not an efficiency indicator. A falling feedpoint resistance after adding radials usually means less ground loss, even if SWR rises a little. Add radials in steps and measure each step; expect diminishing returns. Test choke and radial changes separately so you know what each one did. Confirm with on-air or receive comparisons, repeated enough times to filter out propagation changes. A vertical that reads a bit higher in SWR but sends more of your power into the air is a better antenna than one that looks perfect on the meter and warms the lawn. Let the R and X numbers guide you, and treat a lower SWR as a bonus rather than the goal.
  10. Here is the paperwork side, since that's where people usually get stuck. The FRN (FCC Registration Number) is a free ID you get by registering in the FCC's CORES system. Get it before exam day. Most VE teams ask for it so they can fill out the application (Form 605), and sorting it out at the table can be a hassle. Don't pay anyone for an FRN. If a site asks for money to issue one, you're in the wrong place. ULS (Universal Licensing System) is the FCC database where licenses are recorded. After you pass, the VE team submits your paperwork through their coordinator. When the FCC grants the license, your call sign shows up in ULS. You can search by name or FRN, and the electronic record there is your official license. Wait until your call appears in ULS before you transmit. Passing the test alone doesn't authorize you yet. To find a session, the ARRL's exam session search and HamStudy's session finder are both good starting points. Local radio clubs often post their own schedules. Some VE teams also run online sessions, which is worth knowing if nothing is nearby. Read each listing closely, because it should tell you whether to pre-register, which payment methods are accepted, and what ID to bring. Exam fees are set by the VE team or its coordinator, so they vary. Confirm the amount in the listing and check for any current FCC fee requirements. Don't rely on a number from an old forum post, mine included. Typical things to bring: photo ID, your FRN, a pen or pencil, and a simple calculator if you want one (ask the team about their calculator rules). Also bring a copy of any license you already hold.
  11. Good breakdown. My main addition is to think about what you will actually do with the radio in the first six months. If the answer is local FM nets, a repeater check-in, and the occasional simplex test, a basic dual-bander like the FT-65R covers it, and the money saved can go toward a better antenna, a spare battery, and a programming cable. If you are drawn to digital, check what is active near you. D-STAR, DMR and others are only useful if there are repeaters or reflectors you can reach. On CHIRP, a practical tip is to keep one clean master file with all your local repeaters and simplex channels, then trim it per radio. Name memories in a consistent way, such as the band plus the repeater name or call sign, so the radio's alphanumeric display is useful. Double-check the tone settings: the difference between encode-only Tone and tone squelch confuses a lot of new users, and a wrong tone setting looks just like not reaching the repeater.
  12. Power-wise, size your battery to the mode and the radio, not to a general rule. Estimate average current: a QRP rig on receive might draw a few hundred milliamps, while a 100 W transceiver on transmit draws a lot more. Multiply by time and add a margin. If you're running FT8 or another digital mode on a high-power setting, back the power down. Most digital modes don't need full output, and you'll save both battery and heat. For solar, don't expect much from a small panel on a cloudy day, and don't plan around it as your only source. It's a top-up, not a replacement for a properly sized battery. Keep the panel and controller connections simple, and fuse the battery side. On logging, a paper backup in a waterproof notebook plus an app is a good approach. Write down the UTC date and time and the callsign, band, mode and signal reports, and the park or summit reference. Then do the upload when you're home with a better screen and a better connection. Rushing the upload in the field is where mistakes creep in.
  13. On SO2R, I'd push back slightly on the idea that the software is the hard part. N1MM and other loggers handle the radio switching, keying, and audio routing, but the station design decides whether SO2R works. If the second radio's transmit energy is hitting the first receiver, you'll hear it as clicks, hash, or reduced sensitivity, and no logging setting fixes that. Band-pass filters on each radio and physical separation between antennas on adjacent bands are the standard fixes, and a decent headphone setup that lets you focus on one radio at a time reduces the mental load. A sensible approach is to build up in stages. Start by running on one radio and doing S&P on the other only when your CQ is already playing as a repeated message. Once that feels natural, start using the second radio to find mults between CQs. Trying to alternate rapidly between two active pileups before you've practiced the basics tends to produce busted exchanges and fatigue. For antennas, the demands for running and hunting differ. A run frequency benefits from gain and a clean pattern toward the main population centers, so stacked Yagis or a good single beam on the key bands count most. For hunting mults, a rotatable antenna and a way to listen in different directions matter more, even if the gain is lower. That's why many stations keep a dedicated antenna for the second radio, even if it is only a smaller beam or a dipole, so the two radios aren't fighting over the same aperture. On fatigue, a planned break in a low-rate window usually pays for itself, because tired operators make errors in call copying and exchange entry, and those cost points and sometimes rate when the log has to be corrected. Hydration, food that doesn't cause a crash, and a defined sleep plan matter as much as any piece of hardware. How you split the rest depends on the contest's rules for off-time and your category, so check what applies before you start.
  14. For kit building, a few habits pay off more than a better iron. Sort and identify parts before starting, and check resistor values with a meter rather than trusting color bands in poor light. Fit low-profile parts first, then taller ones. Test in stages: confirm the power rail and current draw before populating the rest of a board. A current-limited bench supply or even a series resistor or fuse in the supply lead can save a board from an accidental short or reversed polarity. Toroids are where many builds go wrong. Turn counting is by the number of times the wire passes through the center hole, not by the number of loops on the outside. Enamel wire needs to be properly stripped and tinned before it is soldered. Check the core material as well: a T37-2 (red) and a T37-6 (yellow) have different permeability, so the same number of turns gives a different inductance. If you have a NanoVNA or an LC meter, check the finished inductor values and sweep the low-pass or bandpass filters rather than assuming the design numbers worked out. On the uBITX in particular, I would treat the stock build as a starting point. The output on the higher bands should be checked for harmonics and spurs, ideally with a spectrum analyzer or at minimum a receiver tuned to the harmonic frequencies. Supply voltage and power headroom matter too, since the PA gets hot at a high duty cycle. Good practice is to use a power supply that can handle the peak current, add reverse-polarity protection, and keep any switching regulator well away from the receive path. A linear supply or a battery is a good reference when you suspect a noisy supply is raising your receiver noise floor. As for what to skip: very simple one-transistor transceivers are fun to build and teach basic ideas, but they do not teach selectivity, AGC, or clean transmit practice. A receiver with a crystal filter and a transmitter with proper low-pass filtering teach more per hour of building.
  15. I'd stress-test the antenna side with a few practical questions. How fast can two people raise the mast and have it guyed correctly? A dipole that takes 40 minutes to deploy is not an EMCOMM antenna. Carrying a quick-deploy backup, such as a simple vertical or an end-fed wire in a tree, is worth the weight. If you use an end-fed half-wave, remember it depends on a counterpoise and is prone to common-mode current, so a choke at the rig end is not optional. For coax, label both ends with length and type, and keep a short list of known-good jumpers and adapters. A lot of field problems are connector problems: PL-259 half-seated on a barrel, a weather-damaged jumper, or a coax that was fine until it got stepped on. A cheap antenna analyzer or SWR meter belongs in the kit. It tells you whether the problem is the antenna system before you start blaming the radio. For the shelter, put the radios where you can reach the key connections with the tent door closed, and keep a drip loop on every cable entering. Put gear on a tarp or table rather than directly on the ground, and tie down anything that could catch wind. For the checklists, I'd write the setup order as: site survey and hazards, power, antenna, radio check on the planned frequencies, and only then logging and message handling. Teardown is mostly the reverse, plus a headcount of stakes, connectors, and adapters, and a note on battery state and anything damaged for the next deployment. Last point: the served agency or net control may care more about your communications plan than your hardware. Know frequencies, check-in procedures, message formats, and backup channels before you go.

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.