Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Dead rig triage: what order do you check things in for no TX, no RX, or a protection fault?

ci_cover.jpg

When a rig shows up on the bench with a vague complaint like "it's dead" or "it receives but won't put out power", it's easy to start poking at the final amplifier or reaching for the soldering iron. A fixed order of checks saves a lot of time and avoids creating a second fault on top of the first. Here's a starting sequence. Please pick it apart and add to it.

1. Power first, and measure it under load. A multimeter reading 13.8 V at the supply with no load tells you very little. Check the voltage at the rig's DC input terminals, then again while transmitting. Look for blown fuses in the rig and in the inline holders on the power cable, which often fail from heat or corrosion rather than overcurrent. Suspect high-resistance crimps, a reverse-polarity protection diode that has gone leaky, and a supply whose current limit or overvoltage crowbar is tripping. A rig that comes alive on the bench supply but dies in the car or shack points to the cabling, not the radio.

2. Separate the radio from the antenna system. Put the rig into a known-good dummy load before judging any transmit or SWR complaint. If the fault vanishes, the problem is the feedline, antenna, tuner or a coax connector. If a high-SWR foldback persists into a good load, the radio itself is misreading, which usually means the SWR bridge, its detector diodes, a reference voltage, or the ALC/protection loop.

3. No receive: settings, then signal path. Rule out the dull stuff first: attenuator or preamp state, squelch, RF gain, AF gain, antenna port selection, a stuck menu setting, and an external speaker jack whose switching contact has gone intermittent. Then divide the receiver into stages. Check that the local oscillator or PLL is locked and on frequency, then work through the front-end filters, the first mixer, the IF and crystal filter, the detector and the audio amplifier. Signal injection from a generator at the antenna jack, then at later stages through a blocking capacitor, quickly shows where the signal disappears.

4. No transmit: confirm the command chain. Check that PTT actually reaches the logic, that the T/R relay or switching diodes change state, that the exciter produces drive, and that the driver and final stages receive bias and supply. A relay that clicks isn't proof the contacts are making good connection, so check continuity across the contacts while keyed.

5. Don't just replace blown finals. Finals rarely fail for no reason. High SWR, parasitic oscillation, a lost bias circuit, an overvoltage supply, a bad heatsink mount with dried thermal compound, or a failed driver stage can all take out the output transistors. If you replace them without finding the cause, the new ones can go the same way. Use the correct type from the manual, check the bias network (resistors, bias diode or thermistor, trimmer), set idle current per the service manual, and bring the rig up on a current-limited supply into a dummy load.

6. Leave capacitors, cleaning and alignment until you know what you're fixing. Old electrolytics are worth replacing in age-related faults such as hum, weak audio, a sagging supply rail or odd startup behaviour, but check polarity and voltage rating, and clean any leaked electrolyte off the board, especially around SMD parts. Contact cleaner has its place on switches, pots and connectors, but use it sparingly and make sure it's safe for the plastics involved. Alignment comes last, and only with the procedure from the service manual and proper test gear. Turning slugs and trimmers at random is how a repairable rig becomes a hard one.

Where do you place the service manual in this order? And which single piece of test equipment do you think pays off the most for the money?

  • Replies 2
  • Views 41
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Administrators

One thing I'd put near the top of the list is looking at the service manual's block diagram and the protection circuit description before touching anything. SWR protection on many rigs isn't one single sensor. It's often a forward/reflected detector, a comparator or microcontroller input, and a drive-reduction path (ALC or a bias cut), and a fault in any of those can look like a bad antenna.

A useful test is to use a good dummy load and a separate wattmeter. If the rig's own meter shows high SWR but the external meter shows the load is fine, the sense circuit is lying. Then you can probe the detector diode outputs with a DMM while transmitting at low power and see whether forward and reflected voltages look reasonable and respond sensibly. A shorted or open diode, a dried-out capacitor on the sample line, or a corroded trimmer can all produce a false trip.

On blown finals, the standard warning is worth repeating: don't power up a repaired PA at full voltage straight away. Use a current-limited bench supply, start with low voltage if the manual allows, confirm idle current with no drive, then apply a little drive into the dummy load and watch for rising current that doesn't track the output. Thermal runaway and oscillation both show up early if you watch the current meter. Also check the output filter and the relay path after a PA failure, because heat or a surge can damage those too.

  • Moderators

On test equipment, a bench supply with an adjustable current limit and a decent DMM cover a surprising number of faults. The next most useful items, in my view, are a dummy load with a wattmeter, then a scope. A scope earns its place when a multimeter would mislead you: supply ripple, switching-regulator noise, a missing clock or oscillator signal, an audio stage that is clipping, or a TX/RX line that glitches rather than switching cleanly. Use the 10x probe setting, keep the ground lead short, and be careful probing RF stages, since the probe capacitance can detune the circuit or stop an oscillator.

For noise complaints, work out whether the noise is coming in through the antenna or being generated inside the rig. Disconnect the antenna and terminate the input. If the noise stays, run the rig from a battery or a different supply. If it disappears on battery, look at the supply and its leads, along with ferrites and grounding. If it remains on battery, then suspect internal sources like a failing electrolytic, a dirty control or a bad solder joint. Tapping the board lightly with an insulated tool while the noise is present sometimes points to an intermittent joint, though it can also cause new problems if you're careless.

On capacitors, measuring ESR with a meter designed for it is more informative than checking capacitance alone, because a capacitor can read near its marked value while having high ESR. And a reminder for tube gear and linear amp supplies: discharge the high-voltage capacitors and verify with a meter before putting your hands in, and use an isolation transformer on mains-powered equipment where appropriate.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.