Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Small-yard HF antennas: comparing EFHW, OCFD, doublet, vertical and loop by what the SWR meter can't tell you

ci_cover.jpg

Many small-yard and HOA antenna threads end up as a contest over whose SWR curve is flattest. That reading only tells you how well the transmitter is matched at the shack end. It says nothing about how much power reaches the air, or at what angle. A dummy load has a perfect SWR and radiates nothing.

Take a typical constrained lot: one or two supports around 30 to 40 ft, a run of 60 to 100 ft to the shack, no room for a full-size 80 m dipole, and a neighbor or covenant that makes anything obvious a problem. These are the questions I'd want to settle before choosing an antenna.

First, what is the feedpoint doing? An end-fed half-wave (EFHW) presents a few thousand ohms at the end of the wire, so it needs a transformer of roughly 49:1 or 64:1 and some counterpoise. On many installs that counterpoise is the outside of the coax, so a common-mode choke at the feedpoint matters. An off-center-fed dipole (OCFD) uses a 4:1 or similar balun and relies on harmonic behavior, and its pattern gets lumpy on some bands. A doublet on ladder line with a tuner has few mysteries, but you need a decent balun or choke at the tuner and a plan for bringing the line into the shack.

Second, where does the loss hide? Coax loss is small on a matched low-band run but climbs with SWR. RG-213 is typically around 0.6 dB per 100 ft at 14 MHz when matched, and thinner coax like RG-58 loses well over twice that, so check the manufacturer's table. A G5RV is a good example: it was designed around a 3/2-wave on 20 m, and elsewhere the ladder-line section transforms the impedance into something the tuner has to fix. If the line then runs through 70 ft of coax at high SWR, the loss can be significant on the higher bands.

Third, height and takeoff angle. A horizontal dipole at 0.25 wavelength or lower leans toward high-angle radiation, which is fine for regional work and not so good for DX. On 40 m, 35 ft is only about 0.25 wavelength. An inverted V at that apex height is a fair compromise, but keep the included angle at 90 degrees or more and keep the ends well out of reach, since the voltage there is high.

Fourth, the ground system on verticals. A ground-mounted vertical with a handful of short radials can lose a large share of power as heat in the soil. Many short radials, or a few resonant elevated radials, usually give better results than a bigger radiator over poor ground.

Magnetic loops and trap dipoles each have their own bargain. A small loop has a narrow bandwidth and a high-Q capacitor, and its efficiency depends heavily on conductor resistance and joint quality, so it can be quiet on receive but weak on 40 m or 80 m. Traps shorten a dipole but add loss and narrow its bandwidth on each band.

On the HOA side, in the US the FCC's PRB-1 asks local governments to reasonably accommodate amateur antennas, but it does not override private deed restrictions, so read the actual covenant text. What are people weighing most when deciding between a wire in the trees, a flagpole-style vertical, or a loop: efficiency, visibility, or noise?

  • Replies 2
  • Views 43
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

I'd put noise on that list ahead of visibility. In a small residential lot, receive noise from switching supplies, LED lighting and the like can matter more than a dB or two of transmit efficiency. A vertical sits close to those sources and picks up a lot of local noise because it's vertically polarized and low. A horizontal wire or a small loop often has a better signal-to-noise ratio even when its absolute signal is lower. S-meter readings are misleading here, so compare in terms of copyable signals, not signal strength.

On the EFHW, the thing that most often causes confusing results is the missing or marginal feedline choke. If the coax shield becomes part of the radiator, the SWR can change when you move the cable, and the shack gets RF in it. A common-mode choke, such as a stack of type 31 ferrite beads or a coiled coax choke with enough turns, is cheap compared to chasing mysteries. Measure the choke's impedance on the bands you care about if you have an analyzer, because a choke that's fine on 20 m can be weak on 80 m.

For a typical small lot with two supports, I'd lean toward a doublet or a simple dipole or inverted V with a tuner. They are predictable, easy to model, and cheap to modify. The EFHW is attractive for portable use and for a single support, but it isn't automatically better than a center-fed wire in the same space.

  • Moderators

The radial question deserves some numbers. A quarter-wave vertical over an ideal ground has a feedpoint around 36 ohms, so a low SWR into 50 ohms can mean either a good match or a lot of ground loss added to the radiation resistance. That's a classic trap: the SWR looks better as the ground gets worse. For a ground-mounted vertical, it's common to recommend 16 or more radials, and more is better. For an elevated vertical, two to four tuned radials per band can work well, and sloping them downward raises the feedpoint toward 50 ohms.

Modeling software such as 4nec2 or EZNEC can help you compare a 35 ft inverted V, a vertical and a loop over your own ground assumptions before cutting wire. Treat the results as relative comparisons, because real soil and nearby wiring change things.

For stealth, thin dark wire is much harder to notice than people expect, especially against trees. A multiband doublet strung between a tree and the house eave may attract less attention than a vertical on a pole. For covenant reasons, a loop in the attic is a fair last resort. Attic wiring, ducting and roofing metal will detune and absorb, though, so expect a compromise and keep RF exposure limits in mind when the antenna is close to living space.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.