Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Dual-band mobile rigs (FTM-500D, ID-5100A, TM-D710G): what matters in the install, and what to check before relying on cross-band repeat

ci_cover.jpg

This thread is for comparing notes on 2 meter / 70 centimeter mobile setups. The three rigs that come up most often for a new install are the Yaesu FTM-500D, the Icom ID-5100A and the Kenwood TM-D710G. All three are dual-band FM mobiles in the 50-watt class, but they are built around different ideas. The FTM-500D is a Yaesu System Fusion (C4FM) radio with analog FM. The ID-5100A is a D-STAR radio with a touchscreen head and analog FM. The TM-D710G is an analog FM radio that puts its emphasis on APRS, with a built-in TNC and a GPS interface. Which one fits depends on what is active on your local repeaters, and on whether you care about digital voice, APRS or just a dependable FM rig.

Here are a few topics to get the discussion going.

1. Mounting and head placement. All three use a separate control head and body, so the body can go under a seat, behind a console or in a trunk while the head sits where you can reach it. The usual mistakes are blocking the heat sink or fan airflow, mounting the body where it can slide into cargo, and putting the head where it interferes with an airbag deployment zone. Mount the body to something solid with screws, not just hook-and-loop tape or double-sided foam. Leave service loops on the control cable and mic cable so nothing is under tension when the seat moves.

2. Power wiring and fusing. The common advice is to run power directly from the battery, with a fuse in the positive lead close to the battery terminal. The fuse protects the wire, so it belongs at the source end. Use the fuse holders supplied with the radio, but check the fuse rating against the manual for your model. Keep the wire gauge adequate for the run length and the rig's peak transmit current. Use a proper grommet where the cable passes through the firewall, and avoid sharp metal edges. A fused distribution block is an alternative if you have several accessories. Switching the radio through an ignition-controlled relay is a reasonable option if you do not want the rig live all the time, but it should not be a way to power the radio through a thin existing circuit.

3. Noise suppression. Start with the antenna, since a poor ground plane or a marginal coax connection will make a noisy install look worse. Then identify the source. Alternator whine usually changes with engine speed. Ignition noise ticks along with the engine. Aftermarket LED lighting, USB chargers, dash cams and DC-DC converters are common offenders even with the engine off. Try turning accessories off one at a time while listening on a quiet frequency. If power-line noise is the problem, ferrite chokes on the DC leads and a clean, short path to the battery can help. Routing the power cable away from the vehicle's other wiring can too.

4. Cross-band repeat. This feature lets the mobile receive on one band and retransmit on the other, which is handy for extending a handheld's reach from outside the vehicle. Do not assume every dual-band mobile supports it, or that it works the same way on every model. Check the manual for the specific rig and firmware before you buy with this in mind. Also check the identification and control-operator rules that apply in your country, because an unattended cross-band setup is still your transmitter. Antenna separation matters too, since a handheld sitting close to the vehicle antenna can cause desense.

5. Mobile etiquette. Keep transmissions short and listen before keying. Let the repeater drop between exchanges so others can join. Remember that driving comes first: use a hands-free mic or voice-friendly workflow where it is legal, and pull over for anything that needs your attention. Check your local laws on handheld and in-vehicle device use, since they vary.

Questions to answer below: Which of these radios has the most practical head-unit layout for you? What was the toughest noise source to track down? And has anyone compared how the digital modes behave in a mobile environment versus plain analog FM?

  • Replies 2
  • Views 36
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

On the choice between the three, I would start with the local network rather than the spec sheet. If the repeaters you use are D-STAR, the ID-5100A makes sense. If they are Fusion or WIRES-X-linked, the FTM-500D is the natural fit. If your area leans on APRS for tracking and messaging, the TM-D710G's built-in TNC is a real advantage because it needs no outboard hardware. A digital-voice radio that nobody around you uses is just a 50-watt FM radio with extra menus.

On wiring, the thing worth repeating is that the fuse protects the cable, not the radio. If the positive lead shorts to the body a foot from the battery, the fuse has to be at the battery end to do anything. Also check that the negative connection is on a clean, bare metal point or the battery negative. A painted or corroded ground point can cause intermittent resets and odd noise that is easy to mistake for a radio fault.

For the cross-band section, I would make sure that anyone planning to use it reads the manual's section on it before assuming it works like a home repeater. Some radios want specific settings for offsets, tones and which band does the receiving, and the ID requirements still apply.

  • Moderators

On noise, a practical order is to check the antenna system first, then the power, then the accessories. Many noise complaints turn out to be a bad coax connector, a poorly grounded mount, or an NMO base sitting on a painted surface. A mag-mount on a roof can also be fine for temporary use, but a permanent mount is more consistent. Use an SWR meter or antenna analyzer to confirm the antenna is tuned for the part of the band you use most. A dual-band whip is a compromise, and it can be well matched on one band and mediocre on the other.

With a noise source you have to find, bring a handheld receiver or a spare radio into the vehicle and listen at the radio's power input and near the suspected devices. Cheap USB chargers and LED lighting deserve suspicion, because many switching supplies put out hash well into the VHF range. If the noise only shows up when something is plugged in, you have your answer.

One more etiquette point: when you call on a repeater while mobile, give your callsign clearly and keep the exchange short. In busy traffic it is fine to say you are mobile and may drop out. That gives the other operator context if you disappear mid-sentence.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.