Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

SSB audio that carries: mic gain, ALC, compression, EQ and bandwidth, and what actually helps on weak signals and DX

ci_cover.jpg

Most advice on SSB audio boils down to "turn the processor up" or "turn it off." Neither is right in every case. A signal that gets through on a weak path is usually clean and intelligible, with consistent average level and no wasted bandwidth. Here is a framework to discuss and argue with, and I'd like to hear where others set their own limits.

1. Start with the microphone and the room. No setting in the radio fixes a poor source. A headset boom mic or a dynamic mic with a good windscreen, held or placed about 1 to 2 inches from the mouth and slightly off-axis, cuts plosives and breath noise. A hard, echoey room gets picked up by condenser mics and by gain-hungry processing. Speaking across a mic at a close, consistent distance usually does more for punch than any EQ menu. Check that your mic matches what your radio expects (impedance, bias voltage, pin wiring), because a mismatch can force you to run the gain at odd levels.

2. Set mic gain by the ALC, not by feel. Speak at a normal DX-style voice level, not a whisper or a shout, and adjust mic gain so the ALC just flickers on voice peaks and stays within the range your manual recommends. If the ALC is pinned, you're overdriving the audio stages and the transmitter is flat-topping. That produces distortion and splatter that widens your signal and makes it harder to copy, even if the meter looks impressive. Remember that ALC is a protective loop, not a loudness control. Many rigs also have a separate drive or power setting, and the meter readings depend on both. Follow your manual first, then confirm with an independent check.

3. Speech processing and compression. A processor reduces the gap between loud and quiet parts of speech, so average power goes up while PEP stays the same. That helps in the noise, because the receiving operator hears more consistent energy. The tradeoffs are that background noise comes up, sibilance and distortion increase, and fatigue sets in for the listener. A mild setting (a few dB of compression, typically the low-to-moderate region of the meter) often sounds better to others than a heavy one. Weak-signal and pileup work can justify somewhat more, but if the audio sounds crunchy or "pumped" in your own recording, back it off. If you run an amplifier, a heavily compressed signal also means more heat and more chance of overdriving, so check the amp's drive requirements and linearity.

4. Equalizer and transmit bandwidth. Voice intelligibility lives largely between about 300 Hz and 2.7 kHz. On the transmit side, rolling off lows below roughly 200 to 300 Hz removes boominess that eats power without improving readability. A modest lift in the 1.5 to 3 kHz region adds presence. Don't boost highs aggressively, since that increases sibilance and spreads energy into the edges of the passband. Many radios let you narrow or shift the TX bandwidth. A typical 2.4 to 2.7 kHz TX width is a decent default. Narrower settings can concentrate energy for DX, but go too narrow and the voice sounds muffled or hard to recognize, especially for people who don't know your accent or callsign.

5. Monitor, but don't trust it blindly. The TX monitor lets you hear your processed audio in your headphones. It's useful for spotting hum, distortion, or too much compression. But it takes the audio from inside the radio, not from the actual RF output, so it can't show you splatter or ALC-induced distortion in your signal. For a real check, listen on a second receiver or SDR (with appropriate attenuation or a dummy load) or ask a local station for a candid report. Reports are subjective and depend on the receiving filters and noise conditions, so look for patterns across several of them.

6. USB vs LSB. By long-standing convention, amateurs use LSB on 160, 80 and 40 meters and USB on 20 meters and above. The 60 meter channels (where applicable under your regulations) are USB. Always check your local band plan and license privileges, since subband edges and sideband rules vary. Using the wrong sideband won't be intelligible and can look like a fault to the other operator. Also note that dial reading and occupied bandwidth differ by sideband, so be careful to stay inside the band edge, particularly at the upper edge on LSB and the lower edge on USB.

7. Receive filters and 2.4 kHz. A 2.4 kHz filter is a solid general-purpose choice for SSB, with a good balance between intelligibility and noise rejection. In a quiet band with a strong signal, wider (2.6 to 3.0 kHz) sounds more natural. In heavy QRM or noise, go narrower (1.8 to 2.1 kHz) or use passband shift or IF shift to move the filter away from the interfering station. Combine that with a notch for carriers and moderate noise reduction. Heavy DSP noise reduction can make weak voices sound watery and hide information, so use as little as helps.

8. Working weak stations and DX. Good receive habits matter as much as TX audio. Use the AGC setting that doesn't pump on noise (often medium or slow for weak signals), keep RF gain and preamp appropriate for the band (on the lower bands, extra preamp often just adds noise and overload), and make sure your tuning is accurate. Because SSB has no carrier to zero-beat, an off-tune voice sounds high-pitched or low-pitched, so tune until it sounds natural. When calling DX, listen first to see whether they're working split, keep your call short, use standard phonetics, and avoid long strings of repeats. Avoid calling over the station being worked. In a pileup, a clean 2.4 kHz signal at modest compression often beats a loud and distorted one.

Where do you set your compression and ALC limits, and what do you use to check your audio, an SDR, a second radio, or reports from other stations?

  • Replies 2
  • Views 50
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Administrators

One point I'd emphasize is the difference between loud and readable. A signal with the ALC pinned and the processor high can show strong on the S-meter, but the extra energy comes from distortion products and splatter, which the receiving operator's filter can't help with. If you do only one test, record your transmit audio through a receiver or SDR into a dummy load and listen back. Listen for hum, a harsh top end, bass boom and pumping between words. Then change one control at a time. If you change mic gain, compression and EQ together, you can't tell which change helped.

On EQ, I'd say cutting is generally safer than boosting. Taking out the lowest end and a touch of the harsh upper edge often makes a voice cleaner than adding presence. If your radio has several EQ presets, treat the names as hints, not rules. Your voice, mic and room decide what works.

  • Moderators

On the receive side, I'd add that narrowing the filter doesn't always make a weak station easier to copy. If you cut too much of the passband, the voice loses the consonant detail you need to catch callsigns and reports. Start at 2.4 kHz and only go narrower when there's a specific interfering signal. Passband or IF shift is often more useful than a narrower filter alone, because it removes the interferer while keeping the main part of the voice.

For DX pileups, there's also a procedural point: audio can't compensate for poor timing. Know whether the DX is operating split, check where they're listening, and call in the gaps. If you're not getting through, a slightly lower pitch of voice and clear phonetics at a steady pace often work better than extra compression or more power. Also check your regulations for power limits and band-edge rules, since those vary by country and license class.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.