When do you leave a good run to chase multipliers? Rate, SO2R and band-change decisions
- Replies 2
- Views 46
- Created
- Last Reply
Top Posters In This Topic
-
Mod_Chad 1 post
-
Mod_Chrissy 1 post
A better way to browse. Learn more.
A full-screen app on your home screen with push notifications, badges and more.
I'd like to compare how people decide when to stop running and go hunting for multipliers. The rule of thumb is simple: run when your rate beats what S&P would give you, and S&P when a new multiplier is worth more than the QSOs you'd lose. Applying it mid-contest is the hard part, because the numbers change with band conditions, the scoring formula and your category.
Here is how I'd frame the decision. Each QSO on a run frequency is worth a certain number of points. A new multiplier adds roughly (total QSO points ÷ current multiplier count) to your score. Early in the contest, with few multipliers, each one is worth a lot, so a slow S&P sweep can pay off. Later, as the multiplier count climbs and the QSO total grows, the break-even shifts. You'll often want to protect a strong run unless a specific multiplier is available that you can't expect to come to you. Per-band multiplier contests make this sharper, because a multiplier worked on 20 meters doesn't count on 15.
The N1MM Logger+ rate and multiplier windows make this easier to see. Rate over the last 10 minutes shows what's happening now, and the 60-minute figure smooths out the noise. A few things I'd check before leaving a run:
1. Is the rate falling because the band is changing, or because someone has moved onto or near your frequency?
2. Do the needed multipliers show up in the bandmap on this band, or would you have to change bands to find them?
3. Will you be able to find another clear run frequency when you come back? On a crowded band, a frequency you gave up may be gone.
Band changes deserve a plan, not a reaction. Most operators work from some kind of propagation expectation: which band is open toward the big population areas at that hour, and when the band will fade. A well-timed change keeps you ahead of the drop in rate, but changing too often costs minutes that never show up in the log. Some operators aim for a minimum time on each band and only break that to grab a multiplier with a strong signal. How rigid are you about that, and do you log the cost of band changes?
SO2R adds another layer. The standard approach is to CQ on radio 1 and use radio 2 to look for multipliers or a second run frequency on another band. Switching is the difficult part. The common trouble spots are audio routing (which ear hears which radio, and how quickly you can swap focus), transmit interlock so you never key both radios into the same antenna system, and band filters so the transmitting radio doesn't desensitize the receiver on the other band. On the same band pair, antenna separation and filtering matter a great deal, and some band combinations simply don't work well without stubs or filters. If you're new to it, one low-risk way in is to keep radio 2 in receive only and use it to scout, then transmit on it only once the routing and interlock are solid.
For spotting, a skimmer feed (such as the Reverse Beacon Network or a local CW Skimmer) and packet spotting can feed your bandmap, but they behave differently. Skimmer spots are quick and automatic, but busted calls are common, especially on weak or fast stations. Packet spots, whether from other operators or from the cluster, are slower and can be wrong, but a human has at least tried to confirm the call. Check that your category allows assistance, because unassisted classes prohibit this. In assisted classes it pays to filter: limit spots to the band and mode you're actually using and to the multipliers you still need, or the bandmap becomes noise. It's also worth listening before you call, since a spot that says a station is on frequency doesn't prove he's there now.
On antennas, the point to debate is where the money and effort are best spent. Stacked Yagis improve takeoff-angle coverage, which can matter a lot when the propagation angle changes through the day. For the low bands, the limiting factor is often the receive system, not the transmit one, so a good receive antenna may help more than a bigger transmit antenna. And for a station that can't have large arrays, are you better off optimizing for a single-band or low-power category where the competition is closer to your capability?
Last, endurance. Fatigue shows up as a drop in accuracy and speed, which is just a drop in rate. Many operators plan off-time around the hours when the bands are weakest, instead of taking breaks whenever they feel tired. They also keep food and water within reach and avoid heavy sugar or caffeine late in the contest. What works for scheduling your sleep in a 48-hour event? And does anyone have a rule for deciding when you're too tired to keep operating well?
Link to comment
https://www.hamradiobase.com/forums/topic/10805-when-do-you-leave-a-good-run-to-chase-multipliers-rate-so2r-and-band-change-decisions/Share on other sites