Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Choosing an SDR for HF through UHF: dynamic range, upconverters, and where the noise really comes from

ci_cover.jpg

This thread is meant as a working discussion of how to match an SDR to the signals you want, and how to avoid the usual gain-staging and noise mistakes. Spec sheets tend to emphasise frequency range and maximum bandwidth. In practice, the ADC resolution, front-end filtering and your antenna system decide how a receiver behaves on a crowded band.

Here is the rough landscape as I understand it. Please correct anything that is off.

RTL-SDR dongles (RTL2832U with an R820T2-class tuner) are cheap and good for VHF/UHF monitoring, ADS-B, rtl_433, POCSAG and similar work. They use an 8-bit ADC, are usually run around 2.4 MS/s to avoid dropped samples, and can overload easily near strong FM broadcast or paging transmitters. Some versions have a direct sampling mode for HF, and the dongle then behaves very differently: the ADC sees the whole spectrum with little filtering, so aliasing and broadcast overload become real concerns. A TCXO model and a ppm correction setting help with frequency accuracy.

HackRF One covers roughly 1 MHz to 6 GHz, has a wide sample rate and can transmit, but it is half-duplex and also has an 8-bit ADC. It is a flexible experimentation tool rather than a high-dynamic-range receiver. LimeSDR hardware offers 12-bit conversion, a very wide tuning range and full-duplex operation, which suits experimenters working with SoapySDR and GNU Radio. SDRplay RSP units and Airspy models target receive performance: higher-resolution ADCs, better filtering, and in some cases built-in notches or preselection. The Airspy HF+ line focuses on HF and VHF with strong large-signal handling at a narrow bandwidth. Check each model's datasheet for exact ranges and bandwidth before buying.

On the software side, SDR# and HDSDR are popular on Windows, and SDRuno is the Windows application for SDRplay hardware. GQRX is the common choice on Linux and macOS, and CubicSDR runs on several platforms via SoapySDR. Most of them can pipe audio to a virtual audio cable or a loopback device, which is how people feed WSJT-X (FT8/FT4), fldigi, DSD-type decoders or multimon-ng. Sample rate, AGC, filter bandwidth and audio level all need setting. Overdriving the decoder's audio input is a frequent cause of failed decodes.

I would like to discuss three things:

1. For HF on an RTL-SDR, is an upconverter better than direct sampling? If so, how do you handle the local oscillator offset in each program? Is it a frequency shift setting, an ExtIO option or something else?

2. How do you decide on gain? A rule I have seen is to lower the gain until the noise floor just starts to rise when the antenna is connected, then check for images or intermod products by changing the gain by a few dB. Is that sound, or are there better tests?

3. What antenna and feedline practices make the biggest difference to the noise floor? Examples would be a common-mode choke, an active loop away from the house, a discone for scanning, and a 137 MHz V-dipole.

  • Replies 2
  • Views 38
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

On the upconverter question: for an RTL-SDR, an upconverter is generally the cleaner route to HF than direct sampling, because the converter gives you proper filtering ahead of the tuner. The cost is an extra oscillator, which adds its own drift and spurs. The software has to know the offset. A common converter uses a 100 MHz or 125 MHz oscillator, so a 7.100 MHz signal appears at 107.100 or 132.100 MHz in the dongle. SDR# has a shift option for this. In HDSDR and similar programs you usually apply the offset through the LO or frequency settings. If the dial reads wrong by exactly the oscillator frequency, the offset has the wrong sign or is missing. If it is off by a few kHz, look at the ppm correction instead.

Your gain test is sound as a starting point, but add one more check. Find a strong local signal, such as a broadcast station, and see whether ghost signals appear elsewhere and move when you change the gain. If they do, the front end or ADC is being overloaded, and it is not a real signal. A filter, for example an FM broadcast notch on a VHF dongle, often does more than reducing gain, because it removes the strong signal before it reaches the amplifier.

One caveat on ADC bits: the theoretical figure is about 6 dB of dynamic range per bit, but real-world performance depends on the tuner, the filtering, the sample rate and the noise in the system. An 8-bit dongle can be perfectly usable with sensible filtering on a narrow job, and a higher-bit receiver will still overload if you feed it a poor antenna system at the wrong gain.

  • Moderators

On antennas and noise: before spending more on the receiver, find out whether your noise floor is set by your environment or by the radio. A simple test is to disconnect the antenna and terminate the input, then reconnect it and compare. If the noise barely changes, the receiver's own noise dominates, and a preamp or a more sensitive radio might help. If the noise jumps up sharply, the noise is arriving from outside, and extra gain only amplifies it.

Typical external sources are switching power supplies, LED lighting, USB 3 devices and the computer itself. A long USB cable with ferrites, or a powered hub, can help. Putting the dongle at the antenna end and sending data down the cable avoids bringing the antenna feedline into the shack's noise field. Common-mode current on the coax is another one: a choke at the radio end and another where the feedline meets the antenna often makes a visible difference on HF.

For specific bands, geometry matters more than the exact model of dongle. A 137 MHz V-dipole for weather satellites uses two elements of roughly 53 cm each, spread at about 120 degrees and oriented horizontally. For ADS-B at 1090 MHz, a quarter-wave element is only about 6.9 cm, so a short vertical element on a ground plane with short, low-loss coax is a good start. For general VHF/UHF scanning, a discone gives wide coverage but is not tuned for any one band. For HF, a magnetic loop or a small active loop can reduce the noise from nearby sources, whereas a long wire picks up everything, which is useful for weak signals but can overload a wideband SDR.

One safety point if you're thinking about a panadapter or bandscope on a transceiver: never share an antenna between a transmitter and a receive-only SDR without proper isolation. Use an IF tap, a dedicated receive output, or a protected splitter or relay arrangement. Transmit power can easily damage a dongle front end.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.