Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Building a Practical 5 W QRP Portable Kit: Rigs, Antennas, Power, and Where to Find Contacts

ci_cover.jpg

Let's pull the practical side of QRP into one thread. Specs and kit lists are easy to find. What's harder is working out which choices make a 5 W station get contacts and which just add weight. Please correct anything below that is out of date, and add what you know.

Why 5 W is workable. The difference between 5 W and 100 W is about 13 dB, a little over two S-units on a typical meter. Going from 5 W to 10 W gains only 3 dB, about half an S-unit. A better antenna, a quieter location, or a more efficient mode will often beat a bigger amplifier. CW has a clear advantage because a narrow receive filter and a trained ear dig signals out of noise that SSB can't. QRP-ARCI's usual definition is 5 W output on CW and 10 W PEP on SSB, which is a useful benchmark when you read contest and award rules.

Rig categories. Roughly, they fall into these groups:

  • Full-featured portable multibands such as the Elecraft KX2 and KX3. They cover CW, SSB, and digital modes, and have built-in ATUs as options. The KX2 is the smaller, lighter one with a lower power ceiling. The KX3 is bigger and gives more headroom and features. Both are far more than a minimal CW rig, and are priced accordingly.
  • Minimal CW field rigs such as the Mountain Topper line (LNR Precision) and the Penntek TR-35. These are built for small size, low current draw, and summit or park activations. The trade-off is a narrower feature set, often limited bands, and usually CW only. Check the current band options and supply voltage range for any specific model before you buy.
  • Simple kits from Hendricks QRP Kits and other small vendors. They are good for learning, and some are also good field radios. Vendor catalogs change, so check what is currently offered.
  • Pixie-style transceivers are extremely simple, very cheap CW rigs, often built around a transistor and an audio amplifier IC. They teach a lot about how a transceiver works. As on-air performance goes, expect poor selectivity and a lot of interference on busy bands. They are a fun build but a frustrating only radio.

Calling frequencies. Commonly used QRP activity areas are around 3.560, 7.030, 10.106, 14.060, 21.060, and 28.060 MHz on CW. On SSB, people often look near 3.985, 7.285, 14.285, and 21.385 MHz. These are conventions rather than exclusive allocations. Check your local band plan and be prepared to move off the calling frequency once you make contact. Also remember that the calling frequency is shared with everyone else. Don't sit on it for a long QSO.

Antennas. With low power, the antenna is where most of the effort should go. Popular choices include:

  • A resonant dipole or inverted-V on a lightweight mast or in a tree. It is simple, efficient, and needs no tuner if cut properly.
  • A linked dipole, which gives multiband operation by connecting or disconnecting wire sections.
  • An end-fed half-wave (EFHW) with a 49:1 or similar transformer. It is quick to deploy and works on a fundamental and harmonics. Feedline common-mode current can be a problem, so consider a choke.
  • A compact magnetic loop, for space-limited sites. It is narrowband and needs retuning, and efficiency drops on lower bands.

Height and clear surroundings matter more than the exact design. Don't skimp on the feedpoint and coax. Lossy small-gauge coax on higher bands wastes some of your precious 5 W.

Power. Many QRP people have moved to LiFePO4 batteries. A 4-cell pack is about 12.8 V nominal and about 14.4 to 14.6 V fully charged, with a flat discharge curve and good cycle life. Before connecting one, check your radio's maximum input voltage (some rigs are happier at 12 V, and a few have a narrower range than others) and use a fuse near the battery. A small 3 to 6 Ah pack can run a QRP rig for many hours, and weighs far less than a comparable lead-acid battery. Don't forget the connectors: Powerpoles are a common standard that make swapping gear easy.

Questions to get things started: what is your minimum field kit, and which part of it has been the most effective improvement for contacts? For those who build, which kit taught you the most about transceiver design?

  • Replies 2
  • Views 36
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Administrators

For anyone choosing between a minimal CW rig and a KX2/KX3-class radio, I would decide based on how you operate rather than on the spec sheets. If you only work CW on one or two bands, a Mountain Topper or TR-35-type radio keeps weight, current drain, and complexity very low. That matters on a long hike, and a small battery will last a long time. If you want SSB, digital modes, general coverage receive, and the flexibility to swap bands as conditions change, the KX2 or KX3 class makes more sense, even though it costs more and draws more current.

One point often overlooked is the receive side. At 5 W, you often win or lose a contact by hearing the other station, not just by being heard. A narrow CW filter, a good AGC, and low-noise audio make a difference. Headphones or earbuds with good isolation help just as much as another watt of output.

Also be careful with the idea that a built-in ATU fixes anything. A tuner makes the radio see a good match, but it does not fix a lossy antenna. A resonant dipole with no tuner at all can beat a poorly matched random wire that tunes with a nice low SWR.

  • Moderators

On the build side, I would suggest treating a Pixie or similar simple kit as a project first and a field radio second. It is a great way to learn about oscillators, keying, and receive audio, and it costs very little. But with no real selectivity, a crowded band is going to sound like several signals at once. If your goal is to make QRP contacts while learning, pair a simple kit with a quiet band, such as the lower edge of 40 or 30 m at a time of day when activity is moderate.

For soldering and troubleshooting, a few basics save a lot of frustration: inspect toroid windings against the instructions, count turns by passes through the core, check that polarized capacitors and diodes are oriented correctly, and measure supply voltage and current before you power up. A cheap multimeter, a dummy load, and a way to measure output power will tell you more than guessing from on-air reports. If you have a nanoVNA or antenna analyzer, check the antenna before you carry it to a hilltop.

On batteries, if you go LiFePO4, label the pack and check the voltage at full charge against your rig's limit. Add a fuse close to the battery, and keep a spare short power lead in the bag. A great many field failures come down to a bad connector or a loose lead, not the radio itself.

If you want a structured way to operate, QRP-ARCI runs contests and awards aimed at low-power operators. Read the current rules on their website because categories and power limits can change from year to year.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.