Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Field comms power and RF layout: keeping generator noise, voltage drop, and coax loss under control

ci_cover.jpg

Planning a portable station for a multi-hour or multi-day deployment (an EMCOMM exercise, a public service event, or a Field Day-style setup) means power and RF problems tend to show up together. Below is a hypothetical baseline to pick apart. Suggested changes are welcome.

Assume a 100 W HF/VHF/UHF setup with an HF transceiver, a dual-band mobile for local nets, a laptop for logging and digital modes, and a small Wi-Fi router for the served agency's forms. Power comes from a 100 Ah LiFePO4 battery, a 200 to 300 W solar panel setup, and an inverter generator as backup. The antennas are a fiberglass mast holding an inverted-V or end-fed half-wave for HF, plus a J-pole or similar vertical for VHF/UHF. The station sits in a pop-up canopy or small tent with sidewalls.

The questions I'd like to work through:

1. Is a DC-first design (battery as the primary source, generator only as a charger) realistic for HF, or does it just move the noise problem to the MPPT controller and the DC-DC converters?

2. How much does coax choice matter on a 50 to 100 ft run, and where do you stop paying for heavier cable?

3. What does a sensible grounding and bonding approach look like in a field setup, as opposed to a fixed station?

4. What belongs on the setup and teardown checklists that people tend to forget, especially under pressure in an activation?

Some numbers to anchor the discussion. A 100 Ah LiFePO4 battery is nominally 12.8 V, so about 1,280 Wh. Plan on using less than the full rating, since the BMS cutoff is a hard stop and cold weather limits charging. A 100 W SSB transmission can pull around 20 A at peak, but voice duty cycle is low, so average current is much smaller than the peak. The peak still sets your wire gauge and fuse sizes. For voltage drop, 20 ft one way of 12 AWG copper is 40 ft round trip, roughly 0.064 ohm. At 20 A that is about 1.3 V lost, which can push a radio below its minimum operating voltage on transmit peaks even when the battery is fine. Heavier wire and shorter runs fix that more cheaply than any other change.

  • Replies 2
  • Views 35
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

On the DC-first question: generally yes, run from the battery and treat the generator as a charger, but don't assume the battery side is automatically quiet. Many MPPT charge controllers and DC-DC converters radiate switching noise on HF, and cheap ones can be worse than a decent inverter generator. The practical approach is to test each noise source individually. With the antenna connected and the receiver on a quiet band like 40 or 20 m, turn things on one at a time: laptop supply, router, controller, solar panels connected or not. Note the S-meter or noise floor change for each. It takes a few minutes at home and you don't have to guess in the field.

For mitigation, put a common-mode choke (a clamp-on or wound ferrite, usually mix 31 for HF) on the DC leads at the radio and on the controller's output and panel leads. Keep the panels and controller physically away from the antenna and its feedline, and don't route coax parallel to DC wiring. If you must run the generator, place it as far away as the cords allow, with the exhaust pointing away from the tent and the operating position. Carbon monoxide is the real hazard here. Never run it inside or beside a shelter, and a battery-powered CO alarm in the tent is cheap insurance. Let it cool before refueling, and store fuel away from the generator and the operating area.

On battery management, wire the battery to a fused distribution block with a fuse per branch, sized to the wire, not just to the load. Powerpole connectors on everything keep polarity consistent. Check your radio's rated input range against the LiFePO4 charge voltage, since a battery sitting near 14.4 V under charge is fine for most modern rigs but not all accessories. Also check the battery's low-temperature charging specification. Many LiFePO4 packs will refuse to charge, or get damaged if forced, below freezing unless they have heating or low-temp protection.

  • Moderators

On coax: for HF at 100 ft, even RG-8X is usually acceptable if the SWR is low, since loss is small enough that you won't notice it. The case for heavier cable like LMR-400 or similar is mostly VHF/UHF, where loss climbs fast. RG-58-type cable loses several dB per 100 ft at 146 MHz, while LMR-400-class cable is roughly 1.5 dB per 100 ft. Check the manufacturer's loss chart for your frequencies rather than trusting rules of thumb. Also remember that high SWR multiplies loss, so a resonant antenna matters more than expensive coax. For EMCOMM, weight and bulk count too. A lighter cable you'll actually carry beats a heavy one left at home.

For feedline noise, a 1:1 current choke at the antenna feedpoint and another at the radio end often does more for receive noise than any other single item. End-fed half-wave antennas need special attention here because the coax can become part of the radiator if the counterpoise is short. Make sure you know what yours is using.

For grounding, I'd separate lightning protection from RF and equipment bonding, because a field ground rod does little for the first and sometimes not much for the second. A ground rod won't protect people or equipment from a nearby strike. The safe policy is to stop operating when thunderstorms approach, disconnect the coax from the radios, and keep people away from the mast. For bonding, tie the equipment chassis together with short, heavy leads so you don't have potential differences between radios, supplies, and the laptop. Follow the generator's manual on grounding and bonding. Many portable units are designed to work without an external ground rod when only powering cords, but don't improvise or back-feed anything.

On masts: keep well away from overhead power lines. A common rule is to stay at least the full mast height plus a generous safety margin away from them. Guy fiberglass poles at more than one level, stake or weight the base for gusts, and plan for wind. Bring a tarp or cable ramps for trip hazards in the shelter area.

Checklist items that often get missed: spare fuses, a few feet of spare coax and adapters, a printed frequency plan and net script, paper logs and pencils, a headlamp with red mode, zip ties and tape, and a way to drain water from the canopy. For teardown, go in reverse order: power down radios, disconnect antennas, lower masts, count stakes and guy lines, wipe down gear, and note any failures for the after-action review. Whatever gets used and tested before the deployment is the gear you can count on during one.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.